欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    DLA MS27754 REV F-2011 SWITCH TOGGLE MINIATURE DOUBLE POLE TOGGLE SEAL LEVER LOCK.pdf

    • 资源ID:696876       资源大小:78.90KB        全文页数:4页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    DLA MS27754 REV F-2011 SWITCH TOGGLE MINIATURE DOUBLE POLE TOGGLE SEAL LEVER LOCK.pdf

    1、AMSC N/A FSC 5930 INCH-POUND MS27754F 13 April 2011 SUPERSEDING MS27754E 20 May 1988 DETAIL SPECIFICATION SHEET SWITCH, TOGGLE, MINIATURE, DOUBLE POLE TOGGLE SEAL, LEVER LOCK This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acq

    2、uiring the product described herein shall consist of this specification sheet and MIL-DTL-83731. Inches mm Inches mm Inches mm .004 .030 .04 .062 .07 0.10 0.76 1.02 1.57 1.78 .072 .090 .10 .175 .27 .428 1.83 2.29 2.5 4.45 6.9 10.87 .47 .51 .535 .575 .740 1.160 11.9 13.0 13.59 14.61 18.80 29.46 NOTES

    3、: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerance is .020 (0.51 mm) on two place decimals and .005 (0.13 mm) on three place decimals. 3. For hardware detail specifications, see supplement of MIL-DTL-83731. 4. Configu

    4、ration of switch case is optional provided maximum dimensions specified are not exceeded. FIGURE 1. Dimensions and configurations. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27754F 2 FIGURE 2. Detail requirements. Provided by IHSNot for Resale

    5、No reproduction or networking permitted without license from IHS-,-,-MS27754F 3 Canceled MS part number 1/ Substitute part number 1/ Available locking combinations Circuits made with toggle lever in Keying side 1-2 4-5 Center position Opposite keying side 2-3 5-6 MS27754-1 MS27754-34 All On 2-3 on 4

    6、-5 On -2 -35 E, F, K, L, M, N Mom-on 2-3 on 4-5 On -3 -36 E, L, N Mom-on 2-3 on 4-5 Mom-on -4 -38 All On 1-2 on 5-6 On -5 -39 E, F, K, L, M, N Mom-on 1-2 on 5-6 On -6 -40 E, L, N Mom-on 1-2 on 5-6 Mom-on 1/ The canceled part numbers are no longer acquirable; the substitute part numbers have a lower

    7、dielectric withstanding voltage at reduced barometric pressure (see test voltage requirement below). REQUIREMENTS: All switches on this standard are designed so that the movement of the switch mechanism is opposite to that of the toggle lever. Test voltage for dielectric withstanding voltage at redu

    8、ced barometric pressure, shall be 400 V rms minimum. Electrical endurance shall be performed for 30,000 cycles. Mechanical endurance shall be performed 50,000 cycles at -65C and then 50,000 cycles at 85C. Intermediate current shall be performed for 30,000 cycles. Terminals shall be molded into the s

    9、witch case and shall accommodate No. 18 AWG wire. Locking arrangement: Positive locking shall be accomplished and shall prevent motion of the toggle lever until the locking mechanism is manually released. The force required to release the locking mechanism shall be 3 to 5 pounds. The locking means a

    10、t the top of the toggle bushing shall be capable of withstanding a torque of 20 pound inches applied in both directions immediately following the humidity test. Maximum weight shall be .045 pound. Electrical ratings for 28 V dc and 115 V ac at 400 Hz. Lamp load = 1 ampere, resistive load = 5 amperes

    11、, inductive load = 2 amperes. Part or Identifying Number (PIN) example: MS27754-36L (locking combination “L“). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27754F 4 Changes from previous issue. Marginal notations are not used in this revision to

    12、 identify changes with respect to the previous issue due to the extent of the changes. Reference documents: MIL-DTL-83731 Custodian: Preparing activity: Army - CR DLA - CC Navy - AS Air Force - 85 (Project 5930-2011-019) DLA - CC Review activity: Army - AV, EA Navy - EC Air Force - 99 NOTE: The acti

    13、vities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-


    注意事项

    本文(DLA MS27754 REV F-2011 SWITCH TOGGLE MINIATURE DOUBLE POLE TOGGLE SEAL LEVER LOCK.pdf)为本站会员(confusegate185)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开