1、 MS24590C INCH-POUND14 May 2007 SUPERSEDING MS24590B 22 September 2000 DETAIL SPECIFICATION SHEET SOCKET, ADAPTER, HOSE TO TUBE, REUSABLE, HYDRAULIC, FUEL AND OIL LINES, 3/16 THROUGH 3/4 INCH TUBING SIZES This specification is approved for use by all Departments and Agencies of the Department of Def
2、ense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-5070. FIGURE 1. Socket dimensions and configuration. AMSC N/A Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-FSC 4730 MS24590C 2
3、Dash number A max/min Inches (mm) B dia Inches (mm) .015 (0.38) C dia Inches (mm) .015 (0.38) D Inches(mm) .015 (0.38)E dia Inches (mm) F dia Inches (mm) G Inches (mm) H Inches (mm) J Inches (mm) K dia Inches (mm) -3 1.010 (25.65) .990 (25.15) .625 (15.88) .563 (14.30) .563 (14.30).500 (12.70).405 (
4、10.29).400 (10.16).130 (3.30) .660 (16.76) .640 (16.26) .170 (4.32) .240 (6.10) .235 (5.97) -4 1.110 (28.19) 1.090 (27.69) .688 (17.48) .625 (15.88) .625 (15.88).560 (14.22).435 (11.05).430 (10.92).100 (2.54) .760 (19.30) .740 (18.80) .170 (4.32) .296 (7.52) .291 (7.39) -5 1.210 (30.73) 1.190 (30.23
5、) .750 (19.05) .688 (17.48) .688 (17.48).640 (16.26).525 (13.34).520 (13.21).100 (2.54) .790 (20.07) .770 (19.56) .180 (4.57) .373 (9.47) .368 (9.35) -6 1.310 (33.27) 1.290 (32.77) .875 (22.23) .813 (20.65) .813 (20.65).750 (19.05).605 (15.37).600 (15.24).150 (3.81) .910 (23.11) .890 (22.61) .200 (5
6、.08) .431 (10.95).429 (10.90)-8 1.660 (42.16) 1.640 (41.66) 1.000 (25.40) .938 (23.83) .938 (23.83).820 (20.83).705 (17.91).700 (17.78).210 (5.33) 1.160 (29.46) 1.140 (28.96) .320 (8.13) .568 (14.43).563 (14.30)-10 1.810 (45.97) 1.790 (45.47) 1.219 (30.96) 1.125 (28.58) 1.125 (28.58)1.000 (25.40).88
7、0 (22.35).870 (22.10).250 (6.35) 1.300 (33.02) 1.280 (32.51) .312 (7.92) .697 (17.70).692 (17.58) -12 2.110 (53.59) 2.090 (53.09) 1.344 (34.14) 1.250 (31.75) 1.250 (31.75)1.160 (29.46)1.025 (26.04)1.015 (25.78).250 (6.35) 1.580 (40.13) 1.560 (39.62) .500 (12.70) .819 (20.80).814 (20.68)FIGURE 1. Soc
8、ket dimensions and configuration - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS24590C 3 Dash number L dia Inches (mm) M min Inches (mm) N Inches (mm) P Q S Inches (mm) -3 .204 (5.18) .201 (5.11) .460 (11.68) -4 .251 (6.38) .247 (6.27
9、) .550 (13.97) .160 (4.06) -5 .330 (8.38) .326 (8.28) .550 (13.97) -6 .387 (9.83) .383 (9.73) .680 (17.27) .010 (.25) 15 .200 (5.08) -8 .526 (13.36) .517 (13.13) .750 (19.05) 30 20 -10 .649 (16.48) .642 (16.31) .978 (24.84) 15 -12 .765 (19.43) .758 (19.25) 1.025 (26.04) .015 (.38) 20 20 .160 (4.06)
10、Dash number T Thread (see note 5) PD U LH round thread (see note 5) V Inches (mm) W -3 .234-32 UNS-2B .2172 .2141 .500-10 3 -4 .281-32 UNS-2B .2639 2607 .530-10 -5 .365-28 UNS-2B .3451 .3418 .640-8 2.5 -6 .421-28 UNS-2B .4014 .3978 .720-8 .031 (.79) 2 -8 .562-24 UNEF-2B - .820-8 1.5 -10 .687-24 UNEF
11、-2B - 1.000-7 -12 .812-20 UNEF-2B - 1.145-7 .047 (1.19) 2 FIGURE 1. Socket dimensions and configuration - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS24590C 4 Dash number X rad Inches (mm) .015 (0.38) Y dia inches (mm) AA inches (mm)
12、 BB inches (mm) CC rad inches (mm) DD rad inches (mm) EE inches (mm) -3 .500 (12.70) .445 (11.30) -4 .109 (2.77) .530 (13.46) .0500 (1.270) .1000 (2.540) .0200 (.508) .025 (.64) .505 (12.83) -5 .640 (16.26) .600 (15.24) -6 .720 (18.29) .665 (16.89) -8 .125 (3.18) .820 (20.83) .0625 (1.59) .1250 (3.1
13、8) .0275 (.70) .032 (.81) .810 (20.57) -10 1.000 (25.40) .0715 (1.82) .1430 (3.63) 1.000 (25.40) -12 .188 (4.78) 1.145 (29.08) .0714 (1.81) .1428 (3.63) .0310 (.79) .040 (1.02) 1.160 (29.46) (29.46 (748.28)NOTES: 1. Dimensions are in inches. 2. Metric equivalents are for information only. 3. Unless
14、otherwise specified, tolerances are as follows: Angles 1; decimals .005 inch (0.13 mm). 4. Unless otherwise specified, maximum surface roughness shall be 125 in Rain accordance with ASME B46.1. 5. Threads shall be in accordance with MIL-S-7742, except round threads. 6. Break all sharp edges and remo
15、ve all hanging burrs and slivers. 7. Thread marks on diameter E shall not be cause for rejection. 8. Part or Identifying Number (PIN). FIGURE 1. Socket dimensions and configuration - Continued. REQUIREMENTS: Dimensions and configurations: The design, construction, and physical dimensions shall be in
16、 accordance with MIL-DTL-5070 and figure 1 in case of conflict between this drawing and MIL-DTL-5070, this drawing shall govern. Intended use. This part is a component of MS24587, MS27224, MS27226, MS27228, MS27230, and MS27232. Materials. Materials shall be in accordance with MIL-DTL-5070. Finish.
17、Finish shall be in accordance with MIL-DTL-5070. Color identification: Color identification shall be accordance with MIL-DTL-5070. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS24590C 5 Part or Identifying Number (PIN) example: MS 24590 -8 AA Mat
18、erial/finish code, see table I Dash number on figure 1 Specification number MS prefix TABLE I. Code for material and finish. Code Dash size Material/finish CC -3 thru -6 Carbon Steel cadmium plating CZ -3 thru -6 Carbon steel zinc plating SS -3 through -6 Corrosion resistant steel - N/A AA -8 throug
19、h -12 Aluminum anodic coating TA -3 through -12 Titanium - Anodized or fluoride phosphated. To the users of this document, it is recommended that the use of carbon steel material with cadmium plating be used only when the other materials and finishes specified in this document cannot meet performanc
20、e requirements. Marking: The PIN and the manufacturers Commercial and Government Entity (CAGE) Code or trademark shall be marked on the socket, see figure 1, or a removable tag securely attached to the socket. Changes from previous issue. Marginal notations are not used in this revision to identify
21、changes with respect to the previous issue, due to the extent of the changes. Referenced documents. In addition to MIL-DTL-5070, this document references the following: ASME B46.1 MS24587 MS27224 MS27226 MS27228 MS27230 MS27232 MIL-S-7742 Provided by IHSNot for ResaleNo reproduction or networking pe
22、rmitted without license from IHS-,-,-MS24590C 6 CONCLUDING MATERIAL Custodians: Preparing activity: Army - AT DLA - CC Navy - AS Air Force - 99 (Project 4730-2005-040) DLA - CC Review activities: Army - AV Navy - MC, SA Air Force - 11, 71 NOTE: The activities listed above were interested in this doc
23、ument as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
