1、 INCH-POUNDMS8003D w/AMENDMENT 1 09 September 2005 SUPERSEDING MS8003D 24 September 2003 DETAIL SPECIFICATION SHEET HOSE ASSEMBLY, POLYTETRAFLUOROETHYLENE, REUSABLE FITTINGS, HIGH TEMPERATURE, MEDIUM PRESSURE, FLARELESS-TO-FLANGE This specification is approved for use by all Departments and Agencies
2、 of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-25579. Hose cut-off factor (HCOF) for assembly with class 1 fittings: See table l. TABLE I. Hose cut-off factor (HCOF) for assembly with class 1 fittings.
3、1/ Fitting ends HCOF (size vs length) 3/ Style 2/ Corrosion resistant steel (CRES) 1 2 8 10 12 16 20 24 A MS27381 MS27054 2.39 2.74 2.78 3.19 3.41 3.88 B MS27381 MS27056 2.41 2.74 3.30 3.56 3.94 4.57 C MS27381 MS27058 2.37 2.73 3.32 3.63 4.06 4.75 MS27384 MS27056 3.20 D MS27382 MS27056 3.19 4.13 4.3
4、1 4.83 5.53 MS27384 MS27058 3.16E MS27382 MS27058 3.18 4.15 4.38 4.95 5.71 MS27385 MS27058 2.52F MS27383 MS27058 2.82 3.84 4.10 4.68 5.36 MS27384 MS27054 3.18G MS27382 MS27054 3.19 3.61 3.94 4.30 4.84 MS27385 MS27054 2.54H MS27383 MS27054 2.83 3.30 3.66 4.03 4.49 MS27385 MS27056 2.56J MS27383 MS2705
5、6 2.83 3.82 4.03 4.56 5.18 1/ Class 1 fittings, styles A through J, are made from CRES. 2/ For depiction of styles see figure 1. 3/ The HCOF is used in the following calculation to determine the hose length required to produce an assembly of a specific size, style and length: Assembly length - HCOF
6、= Hose length. For example, the hose length required to produce an 30.00 inch length assembly of size 20, style F is calculated as follows: 30.00 - 4.68 = 25.32. AMSC N/A FSC 4720 Source: http:/assist.daps.dla.mil - Downloaded: 2005-09-30T07:32ZCheck the source to verify that this is the current ver
7、sion before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8003D w/AMENDMENT 1 2 HCOF for assembly with class 2 fittings: See table ll. TABLE II. HCOF for assembly with class 2 fittings. 1/ Fitting ends HCOF (size vs length) 3/ Styles 2/ (Alum
8、inum and CRES) 1 2 8 10 12 16 20 24 K MS27381 MS27054 2.39 2.74 2.78 3.19 3.41 3.88 M MS27381 MS27056 2.41 2.74 3.30 3.56 3.94 4.57 N MS27381 MS27058 2.37 2.73 3.32 3.63 4.06 4.75 MS27384 MS27056 3.20 P MS27382 MS27056 3.19 4.13 4.31 4.83 5.53 MS27384 MS27058 3.16 R MS27382 MS27058 3.18 4.15 4.38 4.
9、95 5.71 MS27385 MS27058 2.52 S MS27383 MS27058 2.82 3.84 4.10 4.68 5.36 MS27384 MS27054 3.18 T MS27382 MS27054 3.19 3.61 3.94 4.30 4.84 MS27385 MS27054 2.54 U MS27383 MS27054 2.83 3.30 3.66 4.03 4.49 MS27385 MS27056 2.56 V MS27383 MS27056 2.83 3.82 4.03 4.56 5.18 1/ Class 2 fittings, styles K throug
10、h V, are made from combination of aluminum and CRES. 2/ For depiction of styles see figure 1. 3/ The HCOF is used in the following calculation to determine the hose length required to produce an assembly of a specific size, style and length: Assembly length - HCOF = Hose length. For example, the hos
11、e length required to produce an 30.00 inch length assembly of size 20, style F is calculated as follows: 30.00 - 4.68 = 25.32. Source: http:/assist.daps.dla.mil - Downloaded: 2005-09-30T07:32ZCheck the source to verify that this is the current version before use.Provided by IHSNot for ResaleNo repro
12、duction or networking permitted without license from IHS-,-,-MS8003D w/AMENDMENT 1 3 Protective sleeve code: See table lll. TABLE III. Protective sleeve code. Code Type A SAE AS1072 sleeve, fire protection, silicone covered, temperature ranging from -65F to 500F, secured with CRES bands as required.
13、 1/ B SAE AS1073 - code B sleeve, abrasion protection, heat shrinkable, black polyolefin, temperature ranging from -65F to 250 F. C SAE AS1291 - code A sleeve, chafe guard, extruded seamless white PTFE, temperature ranging from -65F to 450F, secured with CRES bands as required. D SAE AS1291 - code C
14、 sleeve, chafe guard, extruded seamless transparent FEP, temperature ranging from -65F to 350F, secured with CRES bands as required. E SAE AS1298 sleeve, heavy wall chafe guard, extruded seamless black PTFE, temperature ranging from -65F to 450F, secured with CRES bands as required. L Lock-wire hole
15、 F Code A + L G Code B + L H Code C + L J Code D + L K Code E + L 1/ To prevent wicking of fluids, the cut end of the fire protective sleeve (code A) shall be coated with Room Temperature Vulcanized (RTV) silicone rubber prior to installation. After installation, cracks and voids in the fire protect
16、ive sleeve shall be coated with RTV rubber to prevent exposure of asbestos or fiberglass. Source: http:/assist.daps.dla.mil - Downloaded: 2005-09-30T07:32ZCheck the source to verify that this is the current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted witho
17、ut license from IHS-,-,-MS8003D w/AMENDMENT 1 4 Class 1 fittings (450F) Corrosion resistant steel Class 2 fittings (275F) Combination aluminum and corrosion resistant steel End 1 End 2 End 1 End 2 NOTES: 1. See tables I and II for fitting ends and HCOF. 2. Fittings shall mate with parts designed to
18、SAE AS33514 and the mounting pad as shown on MS33786. FIGURE 1. Classes 1 and 2 hose assembly styles with flareless-to-flange reusable fittings. Source: http:/assist.daps.dla.mil - Downloaded: 2005-09-30T07:32ZCheck the source to verify that this is the current version before use.Provided by IHSNot
19、for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8003D w/AMENDMENT 1 5 REQUIREMENTS Dimensions: Unless otherwise specified, all dimensions are in inches. Fittings: All fittings shall be qualified in accordance with MIL-DTL-27272. Hose: The hose shall be qualified in a
20、ccordance with MIL-DTL-27267. Assembly classification: Class 1 and class 2 hose assemblies, as specified in MIL-DTL-25579, have been incorporated into the Part or Identifying Number (PIN) as a part of styles (see tables I and II and figure 1). Angular alignment: Hose assemblies with elbow fittings o
21、n each end shall have the angular orientation between the elbows measured counter-clockwise from the centerline of the nearest fitting, positioned at six-oclock, to the centerline of the other fitting (see figure 2). The elbow fitting drop height shall be as shown on figure 3 and table IV. When appl
22、icable, the angular alignment shall be expressed in three digits and specified in the PIN. Protective sleeve: If required, the hose assembly shall include a protective sleeve (see table III) and its code shall be included in the PIN. Fire protective sleeve shall be subjected to testing in accordance
23、 with MIL-DTL-25579. Assembly length: Hose assembly shall be furnished in lengths as specified in the contract or purchase order (see MIL-DTL-25579); however, tolerances on the length of each hose assembly shall be as follows: a. 1/8 inch for lengths under 18 inches. b. 1/4 inch for lengths from 18
24、inches to 36 inches. c. 1/2 inch for lengths from 36 inches to 50 inches. d. 1% for lengths over 50 inches. Flareless fitting, hose connector design: Use MIL-DTL-25579/1 for application of NAS 1760 design. TABLE IV. Size code and elbow fitting drop height. 1/ Dimensions (a), (b), (c) and (d) are dep
25、icted on figure 3. Maximum drop height of elbow fitting Size Reference tube OD Size code (a) 1/ (b) 1/ (c) 1/ (d) 1/ 8 0.500 H 0.642 1.072 0.458 0.92710 0.625 J 0.760 1.427 0.410 0.931 12 0.750 K 0.835 1.661 0.503 1.19116Z 1.000 M 0.889 1.811 0.540 1.317 20Z 1.250 N 0.997 2.091 0.605 1.53524Z 1.500
26、P 1.190 2.473 0.659 1.723 Source: http:/assist.daps.dla.mil - Downloaded: 2005-09-30T07:32ZCheck the source to verify that this is the current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8003D w/AMENDMENT 1 6 NOTE: Angular al
27、ignment shall be measured in degrees with a tolerance of 2. FIGURE 2. Measurement of angular alignment between elbow fittings. NOTES: 1. Hose assembly length “L” shall be measured, with the hose laid out horizontally and straight between the centers of the nipple end and the flange-sealing surface,
28、along a straight line parallel to the hose length. 2. See table IV for dimensions of (a), (b), (c) and (d). Dimensions (a) and (b) are measured to the end of a ball nose style fitting. Adjustments should be made for a NAS 1760 style fitting see requirements application of NAS 1760 and ball nose styl
29、e fitting. FIGURE 3. Elbow fitting drop height, dimensions (a), (b), (c) and (d). Source: http:/assist.daps.dla.mil - Downloaded: 2005-09-30T07:32ZCheck the source to verify that this is the current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without licen
30、se from IHS-,-,-MS8003D w/AMENDMENT 1 7 PIN: The PIN for each hose assembly shall include its size code, length, style, protective sleeve type, and the angular alignment between the elbow fittings, as applicable. Example: The PIN for an 8.250 inch (209.55 mm) length, style F hose assembly with a .50
31、0 inch (12.70 mm) tube OD, a fire protective sleeve in accordance with SAE AS1072, and a 30 between the elbow fittings shall be as depicted below. 08 2 F AH Amendment notations. The margins of this specification are marked with vertical lines to indicate modifications generated by this amendment. Th
32、is was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations. MS8003 030Angular alig
33、nment between elbow fittings as specified on figure 2 (leave blank for styles A, B, C, G, H, K, M, N, T, and U. Protective sleeve type (see table III). Leave blank if not required. If a protective sleeve is not required, the PIN shall be as follows: MS8003H082F030. series seal end.Length in inches f
34、rom MS8000 series seal end.Specification number.Size code (see table IV). Source: http:/assist.daps.dla.mil - Downloaded: 2005-09-30T07:32ZCheck the source to verify that this is the current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from
35、IHS-,-,-Length in eights of an inch from MS8000 Style (see table I and figure 1). MS8003D w/AMENDMENT 1 8 Referenced documents. In addition to MIL-DTL-25579, this document references the following: MIL-DTL-27267 MIL-DTL-27272 MIL-DTL-25579/1 MS27385 MS27383 MS33786 MS27384 MS27054 MS27381 MS27056 MS
36、27382 MS27058 NAS 1760 SAE AS33514 SAE AS1291 SAE AS1298 SAE AS1073 SAE AS1072 CONCLUDING MATERIAL Custodians: Preparing activity:Army - AV DLA - CC Navy - AS Air Force - 99 (Project 4720-0430-000) DLA - CC Review activities: Army - AR, AT, EA, MI Navy - MC, SA, SH Air Force 71 NOTE: The activities
37、listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Source: http:/assist.daps.dla.mil - Downloaded: 2005-09-30T07:32ZCheck the source to verify that this is the current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
