欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    DLA MIL-PRF-46846 D-2013 RUBBER SYNTHETIC HEAT - SHRINKABLE.pdf

    • 资源ID:692949       资源大小:528.16KB        全文页数:16页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    DLA MIL-PRF-46846 D-2013 RUBBER SYNTHETIC HEAT - SHRINKABLE.pdf

    1、 AMSC N/A FSC 5970 INCH POUND MIL-PRF-46846D 02May2013 SUPERSEDING MIL-PRF-46846C 29December1998 PERFORMANCE SPECIFICATION RUBBER, SYNTHETIC, HEAT - SHRINKABLE This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification

    2、covers the type and class requirements for extruded tubing, molded parts, and extruded shapes that are flexible, electrical insulating and whose dimensions will reduce to a predetermined size upon the application of heat. 1.2 Classification. The heat-shrinkable rubber will consist of the following t

    3、ypes and classes, as specified (see 6.2). Type I. Cross-linked, modified polychloroprene (Neoprene) molded parts, and extruded shapes, flexible general purpose cable-jacketing, cable harness, boots and transitions, service temperature range of -55 to 90C. Class 1 - Deleted (see 6.4.1). Class 2 - Mol

    4、ded parts and extruded shapes, cable harness boots and transitions, expansion ratio 2.5. Type II. Cross-linked, modified flame-retardant silicone rubber tubing, molded parts and extruded shapes, highly flexible, ablative-resistant. Class 1 - Tubing, expansion ratio 1.75, service temperature range of

    5、 -70 to 180C. Comments, suggestions, or questions on this document should be addressed to: Defense Supply Center Richmond (DSCR), ATTN: DLA-Aviation, 8000 Jefferson Davis Highway, Richmond, VA 23297-5610 or emailed to STDZNMGTdla.mil. Since contact information can change, you may want to verify the

    6、currency of this address information using the ASSIST database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-46846D 2 Class 2 - Molded parts and extruded shapes, expansion ratio 2 to 4, service temperature range -7

    7、5 to 135C. Type III. Cross-linked, fluoroelastomer, modified polymer of hexafluoropropylene and vinylidene fluoride dipolymer, molded parts and extended periods of high temperature and solvent attack. Class 1 - Tubing, expansion ratio 2, service temperature range -55 to 200C. Class 2 - Molded parts

    8、and extruded shapes, expansion ratio 3.5, service temperature range of -55 to 200C. Type IV. Cross-linked, modified, propellant-resistant butyl rubber tubing, molded parts and extruded shapes, flexible for protection of cable assemblies exposed to hypergolic fuels. Class 1 - Tubing, expansion ratio

    9、2, service temperature range of -55 to 125C. Class 2 - Molded parts and extruded shapes, expansion ratio 2.5, service temperature range of -55 to 125C. Type V. Deleted (see 6.4.2). Type VI. Cross-linked, modified, flame-resistant ethylene-propylene rubber tubing, molded parts, extruded shapes, flexi

    10、ble, ozone resistant, and mechanically tough. Class 1 - Tubing, expansion ratio 2, service temperature of -70 to 115C. Class 2 - Molded parts and extruded shapes, expansion ratio 4, service temperature range of -75 to 125C. 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section ar

    11、e specified in sections 3 and 4 of this specification. This does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that t

    12、hey must meet all specified requirements documents cited in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards and handbooks. The following specifications, standards, and handbooks form a part of this document to the exte

    13、nt specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-46846D 3 STANDARDS FEDERAL FED-STD-376 Preferred Metric Units for

    14、General Use By The Federal Government DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-5606 Hydraulic Fluid, Petroleum Base: Aircraft; Missile, and Ordnance MIL-PRF-7254 Propellant, Nitric Acid MIL-PRF-7808 Lubricating Oil, Aircraft Turbine Engine, Synthetic Base MIL-PRF-26539 Propellants, Dinitrogen Te

    15、troxide MIL-PRF-27402 Propellant, Hydrazine - UNS-Dimethylhydrazine (50% N2H4 - 50% UDMH) (Copies of these documents are available online at http:/assist.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Non-Gover

    16、nment publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) ASTM D257 - Standard Test Method for D

    17、C Resistance or Conductance of Insulating Materials ASTM D412 - Standard Test Method for Vulcanized Rubber and Thermoplastic Elastomers - Tension ASTM D570 - Standard Test Method for Water Absorption of Plastics ASTM D635 - Standard Test Method for Rate of Burning and/or Extent and Time of Burning o

    18、f Plastics in a Horizontal Position ASTM D746 - Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact ASTM D792 - Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement ASTM D876 - Standard Test Method for Nonrigid Vinyl

    19、Chloride Polymer Tubing Used for Electrical Insulation ASTM D1149 - Standard Test Method for Rubber Deterioration Surface Ozone Cracking in a Chamber ASTM D2240 - Standard Test Method for Rubber Property-Durometer Hardness ASTM D2671 - Standard Test Method for Heat-Shrinkable Tubing for Electrical U

    20、se ASTM G21 - Standard Practice for Determining Resistance of Synthetic Polymeric Materials to Fungi, Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-46846D 4 (Copies of these documents are available from www.astm.org or ASTM International, 1

    21、00 Barr Harbor Drive, West Conshohocken, PA 19428-2959.) 2.4 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, howe

    22、ver, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 First article. When specified (see 6.2), a sample shall be subjected to first article inspection (see 6.3) in accordance with 4.3. 3.2 Toxic chemicals, hazardous substances, and ozone d

    23、epleting substances (ODS). The use of toxic chemicals, hazardous substances, or ODS shall be avoided, whenever feasible. 3.3 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provid

    24、ed that material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.4 Materials. Type I synthetic rubber specified herein shall be fabricated from a cross- linked, stabilized, modified polychloroprene (Neoprene) composition. Type

    25、 II synthetic rubber shall be fabricated from a cross-linked, stabilized, flame-retardant, modified silicone rubber composition. Type III synthetic rubber shall be fabricated from a cross-linked, stabilized, flame- resistant, fluorelastomer, modified polymer of hexafluoropropylene and vinylidene flu

    26、oride dipolymer. Type IV synthetic rubber shall be fabricated from a cross-linked stabilized, propellant-resistant, modified butyl rubber composition. Type VI synthetic rubber shall be fabricated from a cross-linked, stabilized, flame-resistant, modified ethylene-proplylene rubber composition. These

    27、 expanded synthetic rubbers shall shrink to predetermined dimensions upon the application of heat as follows: a. Types I, IV, and VI - Heat in excess of 135C. b. Types II, III - Heat in excess of 175C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

    28、MIL-PRF-46846D 5 3.5 Dimensions and tolerances (see table I). 3.5.1 Extruded tubing. 3.5.1.1 Sizes and tolerances. Unless otherwise specified (see 6.2), types II through VI extruded tubing shall have the sizes and tolerances specified in table I, as supplied and after heating (see 4.4.2.3.3). 6.2).

    29、3.5.1.2 Length. The length of tubing shall be as specified in the contract or order (see 3.5.2 Molded parts and extruded shapes. The dimensions and tolerances of heat- shrinkable molded parts and extruded shapes shall be as specified on the applicable drawings or as specified in the contract or orde

    30、r (see 6.2). 3.5.3 Nonstandard dimensions. 3.5.3.1 Nonstandard thicknesses and shapes. Nonstandard thicknesses and shapes shall be specified by the procuring activity. Dimensional tolerances for these nonstandard thicknesses or shapes shall conform to the tolerances for the nearest standard size, un

    31、less otherwise specified (see 6.2). 3.5.3.2 Length. If applicable, the length of tubing shall be as specified in the contract or order (see 6.2). 3.5.4 Storage. The heat-shrinkable tubing, molded parts, and extruded shapes shall meet the requirements of this specification after accelerated storage c

    32、onditioning (see 4.3.1 and 4.3.2). 3.6 Physical, electrical, and chemical properties. 3.6.1 Tubing. Types II through VI, class 1, synthetic rubber tubing shall have the physical, electrical, and chemical property requirements as specified in table II (see 4.4.2.1). 3.6.2 Molded parts and extruded sh

    33、apes. Types I through VI, class 2, synthetic rubber molded parts and extruded shapes, shall have the physical, electrical, and chemical property requirements (see 4.4.2.2) as specified in table III. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-6 M

    34、IL-PRF-46846D TABLE I. Tubing sizes and tolerances, types II through VI, class 1. EXPANDED - AS SUPPLIED RECOVERED DIMENSIONS - AFTER HEATING MINIMUM INSIDE DIAMETER, INCHES MAXIMUM INSIDE DIAMETER, INCHES WALL THICKNESS, INCH Size, Inches Type II Type III Type IV Type VI Type II Type III Type IV Ty

    35、pe VI Type II Type III Type IV Type VI 0.25 0.250 0.250 0.250 0.250 0.143 0.125 0.125 0.125 .035.010 .030.010 .035.010 .030.010 0.375 0.375 0.375 0.375 0.375 0.214 0.187 0.187 0.187 .040.010 .035.010 .040.010 .035.010 0.5 0.500 0.500 0.500 0.500 0.286 0.250 0.250 0.250 .048.010 .043.010 .050.015 .04

    36、3.010 0.625 0.625 0.625 - 0.625 0.357 0.312 - 0.312 .052.015 .047.012 - .047.012 0.75 0.750 0.750 0.750 0.750 0.428 0.375 0.375 0.375 .057.015 .052.015 .060.015 .052.015 0.875 0.875 0.875 - 0.875 0.500 0.437 - 0.437 .065.015 .060.015 - .060.015 1.0 1.00 1.00 1.00 1.00 0.570 0.500 0.500 0.500 .070.01

    37、5 .065.015 .075.020 .065.015 1.25 1.25 1.25 - 1.25 0.714 0.625 - 0.625 .087.020 .070.020 - .070.020 1.5 1.50 1.50 1.50 1.50 0.857 0.750 0.750 0.750 .095.020 .075.020 .100.020 .075.020 1.75 1.75 - - - 1.00 - - - .107.020 - - - 2.0 2.00 2.00 2.00 - 1.14 1.00 1.00 - .110.020 .110.020 .110.020 - 2.5 - -

    38、 2.50 - - - 1.25 - - - .130.020 - 3.0 - - 3.00 - - - 1.50 - - - .140.020 - 4.0 - - 4.00 - - - 2.00 - - - .150.020 - Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-7 MIL-PRF-46846D TABLE II. Physical, electrical, and chemical properties of synthetic

    39、rubber tubing, class 1. Property Conditioning (see 4.4.2.3) Requirement Method Type II Type III Type IV Type VI Type II Type III Type IV Type VI Longitudinal Change percent, maximum A A E4/-95 E4/572 E168/352 E168/392 A A E24/77 E24/77 E24/77 A A A E4/-40 E4/-572 E168/482 E168/482 A A E24/77 E24/77

    40、E24/77 A A A E4/-67 E4/392 E96/902 E168/302 A A E24/77 E1/2/77 E1/2/77 A A A E4/-103 E4/392 E168/302 E96/302 A A E24/77 E24/77 E24/77 A 10 20 15 15 Paragraph 4.5.3 Tensile Strength, psi, minimum 600 1200 1200 1400 (See 4.4.2.1) Tensile Stress at 100 percent elongation, psi, maximum 500 1400 1200 100

    41、0 (See 4.4.2.1) Elongation, percent, minimum 200 250 250 200 (See 4.4.2.1) Specific Gravity, maximum 1.35 2.0 1.40 1.25 (See 4.4.2.1) Hardness, Shore A 60 5 82 5 85 5 80 5 ASTM D2240 Low Temperature Pass or Fail Pass or Fail Pass or Fail Pass or Fail (See 4.4.2.1) Heat Shock - No dripping, flowing o

    42、r cracking- Paragraph 4.5.4 Heat Aging, followed by tests for: Paragraph 4.5.5 Tensile Strength, psi, minimum 500 1200 1000 1200 (See 4.4.2.1) Elongation, percent, minimum 120 200 100 100 (See 4.4.2.1) Dielectric Strength, volts/mil, minimum 300 150 100 220 (See 4.4.2.1) Volume Resistivity, ohm-cm,

    43、minimum 1 X 1011 1 X 109 1 X 1010 1 X 1011 (See 4.4.2.1) Flammability, seconds maximum 60: self-exting. 1/ Method A 15: self exting. Method B - 15: self exting. Method A (See 4.4.2.1) (Use indicated method) Fungus Resistance Rating of 0 - ASTM G21 Water Absorption, percent, maximum 1.0 0.5 0.5 1.0 (

    44、See 4.4.2.1) (Procedure A) Solvent Resistance, followed by tests for: Paragraphs 3.7 and 4.5.6 Tensile strength, psi, minimum 400 1200 1000 500 (See 4.4.2.1) Elongation, percent, minimum 120 250 200 100 (See 4.4.2.1) Eccentricity, percent, minimum 60 60 60 60 ASTM D2671 1/ Not more than 25 percent o

    45、f indicator flag burned; no dripping or flowing. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-8 MIL-PRF-46846D TABLE III. Physical, electrical, and chemical properties of synthetic rubber molded parts and extruded shapes, class 2. Property Conditi

    46、oning (see 4.4.2.3) Requirement Method Type I Type II Type III Type IV Type VI Type I Type II Type III Type IV Type VI Elastic Memory, percent, minimum A A E4/-67 E4/302 E96/212 E96/212 A A E24/77 E24/77 E24/77 A A E4/-104 E4/432 E96/347 E96/347 A A E24/77 E24/77 E24/77 A A E4/-87 E4/572 E168/482 E1

    47、68/482 A A E24/77 E24/77 E24/77 A A E4/-67 E4/572 E96/302 E96/302 A A E24/77 E1/77 E1/77 A A E4/-103 E4/437 E168/302 E168/302 A A E24/77 E24/77 E24/77 Expansion 150 Retraction 90 Expansion 250 Retraction 90 Expansion 200 Retraction 90 Expansion 150 Retraction 90 Expansion 275 Retraction 93 Paragraph

    48、 4.5.2 Tensile Strength, psi, minimum 1500 600 1800 1200 1600 ASTM D412, Die D Tensile Stress at 100 percent elongation, psi, maximum 750 600 1200 1000 750 ASTM D412, Die D Elongation, percent, minimum 200 200 300 250 450 ASTM D412, Die D Specific Gravity, maximum 1.50 1.35 1.95 1.40 1.25 ASTM D792 Hardness, Shore A 78 5 83 5 85 5 90 5 85 5 ASTM D2240 Low Temperature P


    注意事项

    本文(DLA MIL-PRF-46846 D-2013 RUBBER SYNTHETIC HEAT - SHRINKABLE.pdf)为本站会员(priceawful190)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开