1、 MIL-PRF-1/1065G 14 July 2009 . SUPERSEDING MIL-E-1/1065F 25 June 1999 PERFORMANCE SPECIFICATION SHEET ELECTRON TUBE, CATHODE RAY TYPE 5BCP7 This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the electron tube described
2、 herein shall consist of this document and the latest issue of MIL-PRF-1. DESCRIPTION: Miniaturized, magnetic deflection and focus. DIMENSIONS AND PIN CONNECTIONS: See figure 1. ABSOLUTE RATINGS: Parameter: Unit: Ef V Ec1 V dc Eb1 V dc Ehk V dc Rg1 Meg Alt ft Maximum: Minimum: 6.9 5.7 0 -200 11,000
3、5,000 180 - 1.5 - 80,000 - Test condition: 6.3 Adjust 6,000 - - - See footnotes at end of table I. GENERAL: Qualification - Required. 1/ AMSC N/A FSC 5960 INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-1/1065G 2 TABLE I. Testing a
4、nd inspection. Limits Inspection Method MIL-STD-1311 Notes Conditions Symbol Min Max Unit Qualification inspection Vibration 5111 - Width - 2.0 mm Pressure implosion 1141 - - - - - Barometric pressure, reduced 1002 2/ 20 mmHg - - - - Direct-interelectrode capacitance 1331 - k to all g1 to all Ck Cg1
5、 - - 5.5 5.5 pF pF Cathode illumination 5216 - - - - - Conformance inspection, part 1 Voltage breakdown 5201 - - - - - Voltage breakdown (magnetic types) 5201 - - - - - Neck straightness 5101 - Cylinder length = 4 inches (101.6 mm); ID = .901 inches (22.89 mm) maximum - - - - Screen and faceplate bl
6、emishes 5106 - - - - - Modulation 5223 - Ib = 200 A dc Ec1 - 34 V dc Screens 5221 - Eb1 = 5,000 V dc; Ib1 = 48 A dc cB1 640 - cB Spot position (magnetic deflection) 5231 - - - 6 mm Zero-bias anode current (magnetic deflection) 5236 3/ - - - - Focusing coil current - 4/ Ib = 200 A dc D = 2.375 inches
7、 (60.33 mm) - 48 72 mA dc Grid-cutoff voltage 5241 - - -19 -56 V dc Grid No. 1 leakage current 5251 - - - - - See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-1/1065G 3 TABLE I. Testing and inspection - Continued
8、. Limits Inspection Method MIL-STD-1311 Notes Conditions Symbol Min Max Unit Conformance inspection, part 2 Heater current 1301 - If 270 330 mA Side terminal and base alignment 5101 - Halfway between pins No. 1 and No. 9 - - - - Neck and bulb alignment (magnetic types) 5101 5/ - - - - Face tilt 5101
9、 5/ - - - - Stray light emission (conventional types) 5216 - Eb1 = 11,000 V dc - - - - Screen (P7 type) 5221 - Eb1 = 5,000 V dc; Ib1 = 48 A dc - - - - Line width A (magnetic deflection) 5226 6/ Ib = 200 A dc Width - 0.33 mm Heater cathode leakage current 5251 - Ehk = +180 V dc Ehk = -180 V dc Ihk Ih
10、k - - 15 15 A dc A dc Astigmatism - 7/ Ratio - 1.20 - Permanence of marking 1105 - - - - - Conformance inspection, part 3 Life test - - Group C; Eb1 = 11,000 V dc; Ib = 60 A dc; t = 500 hours - - - - Life-test end points: Line width A Modulation - 5226 5223 - - 200 A dc; 200 A dc Width Ec1 - - 0.33
11、34 mm V dc 1/ The following information and materiel shall be made available to the Government representative conducting the qualification inspection measurements with four regular qualification samples: (a) The gun drawing with significant dimensions. (b) A sample of the gun to be used in manufactu
12、ring of the tubes. 2/ Maximum rated voltages are applied to all electrodes connected through the base, and with tube in cutoff conditions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-1/1065G 4 TABLE I. Testing and inspection - Continued.
13、3/ The following values are to be used in place of those specified in method 5236: Negative grid cutoff voltage Minimum O-bias current A Negative grid cutoff voltage Minimum O-bias current A 19 250 38 480 20 250 39 500 21 250 40 520 22 250 41 540 23 250 42 560 24 250 43 580 25 250 44 600 26 270 45 6
14、20 27 285 46 640 28 300 47 660 29 310 48 680 30 335 49 700 31 350 50 725 32 370 51 750 33 390 52 775 34 405 53 800 35 425 54 825 36 445 55 850 37 460 56 875 4/ Use JEDEC No. 127 focus coil, or equal. Focusing coil current shall be determined at the focus setting used in the astigmatism test. 5/ The
15、two sets of neck supports, referenced in method 5101, shall be spaced 1.125 inches (28.58 mm) and 3.375 inches (85.73 mm) below reference plane. 6/ Line width A shall be the maximum line width obtained in the astigmatism test. 7/ With a single line, 4.5 inches (114.30 mm) in length and 1/60-second d
16、uration, repeated at a rate of 60 Hz, modulate grid No. 1 with 1-microsecond pulses. Adjust the peak beam current to 200 A dc and focus for the most circular spot at the center of the screen. Display a partially merged nonlinear raster and note the orientations for greatest and least mergings as the
17、 raster is rotated. Maintain this focus and proceed according to method 5226, to determine the line widths for those two orientations. Astigmatism (the ratio of the maximum to the minimum line width) shall not exceed the value specified. Provided by IHSNot for ResaleNo reproduction or networking per
18、mitted without license from IHS-,-,-MIL-PRF-1/1065G 5 NOTES: 1. These dimensions are for information only and are not required for inspection purposes. 2. Useful screen. 3. Determined by point where leading edge of JEDEC reference line gauge G123 will stop. 4. External conductive coating shall be ti
19、ed to cathode potential (by external application circuitry). FIGURE 1. Outline drawing of electron tube type 5BCP7. Dimensions Ltr Inches Millimeters Min Max Min Max Conformance inspection, part 2 A 6.750 7.250 171.45 184.15 C .810 DIA .896 DIA 20.57 DIA 22.76 DIA D 2.125 R - 53.98 R - P .938 1.062
20、23.83 26.97 Q .188 .250 4.78 6.35 R .563 .813 14.30 20.65 Qualification inspection B 4.900 DIA 5.000 DIA 124.46 DIA 127.00 DIA E 2.750 2.875 69.85 73.03 G Base: E9-37 (EIA) S Bulb contact: J1-22 (EIA) Reference dimensions (see note 1) F 24.000 R 609.60 R K 9.660 R 245.36 R L .125 R 3.18 R M .125 R 3
21、.18 R J 2 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-1/1065G 6 In addition to MIL-PRF-1, this document references the following: MIL-STD-1311 Marginal notations are not used in this revision to identify changes with respect to the prev
22、ious issue due to the extent of the changes. Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 85 (Project: 5960-2009-015) DLA - CC Review activities: Army - CR4 Navy - AS, CG, OS, SH Air Force 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
