欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    DLA MIL-HDBK-60-1990 THREADED FASTENERS - TIGHTENING TO PROPER TENSION《由紧到合适张力线状扣件》.pdf

    • 资源ID:691411       资源大小:1.23MB        全文页数:34页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    DLA MIL-HDBK-60-1990 THREADED FASTENERS - TIGHTENING TO PROPER TENSION《由紧到合适张力线状扣件》.pdf

    1、t - MIL-HDBK-60 TH m 7777770 005L1364 4 MIL-HDBK-6 O 12 March 1990 MILITARY HANDBOOK THREADED FASTENERS - TI-NING TO PROPER TENSION Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-HDBK-60 FORFGIORD 1. This military handbook is approved for use by

    2、 all Departments and Agencies of the Department of Defense. 2. Benef Mal comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Avenue, Philadelphia, PA 19111-5096, by using the self-addressed Standardiza- tion D

    3、ocurrient Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. Appendix Al2 of FED-STD-H28, Screw-Thread Standards for Federal Services. Defense Industrial Supply Center, AiTN: DISC-ECF, 700 Robbins 3 The contents of this handbook replace the information contained

    4、in ii Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-HDBK-60 TH m 9779770 005Li36b A m MIL-HDBK-6Q CONTENTS PARAGRAPH 1 . SCOPE . 2 . Al?PLICA3rn lxxmmm 3 . EEFINITIQNS 4 . GEMERALI INFORMATION ON PRELQADS 4.1 Preload for bolts in axial loaded j

    5、oints . 4.2 Preload for bolts in shear loaded joints . 4.3 Preloa for bolts in combined shear and axial Loaded joints . 5 . PRELOAD APPLICATION . 5.1. Preload application - general 5.2 Preload below yield point 5.3 Preload above yield pint 5.4 Preload limitation . 5.5 Preload adjustrrients 5.5.1 Tor

    6、sion load compnent . 5.5.2 Preload relaxation . 5.5.3 Preload uncertainty 5.5.4 Temperature effects 5.6 5.4 Flange joint bolt tensioning . Back-turning following preload application . 6 . MFTHOS FOR CCNIROLLING BOLT TENSION 6.1 6.2 6.2.1 6.2.2 6.2.3 6.2.4 6.2.5 6.2.6 6.3 6.3.1 6.3.2 6.3.3 6.4 6.4.1

    7、6.4.2 6.4.3 5,4.4 6.5 6. 6 6.6.1 6,6.2 6 . 7 Controlling bolt tension . general . Elongation measurement - stress below proportional limit Micrometer: method Modified micrometer method . Indicating bolt Turn-of-nut method . Ultrasonic method Strain gage method . Direct loading . Jacking methods Heat

    8、ing-temperature control Heating-elongation control . Mechanical effect of load Washer or washer-face deformation Washer OK hex fastener tab fracture Conical spring nut . Change in sonic velocity under stress Yield pint tensioning . Torque control . Torque wrench Torque limiting fasteners 000.00000sB

    9、.0600. Tbrcye-tension eompxison PACE 1 . 2 3 6 6 6 6 6 6 6 7 10 10 10 10 12 12 12 12 13 13 14 14 14 15 15 15 15 16 16 16 16 16 17 17 17 17 14 iii Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-HDBK-60 TH W 7777770 005Ll3b7 T MIL-HBK-60 CONTEM3 -

    10、 (Contd) FIGURES 1. Bolt load in joint with applied axial load * 2. Percent increase in tensile stress due to torsional load application; Unified screw threads 3. Percent increase in tensile stress due to torsional load application; UNJ screw threads . ; 4. Example of tightening order for pairs of f

    11、lange bolts . 5. Effective length applicable in elongation formula . 6. Drilling for elongation determination when one end is not accessible . .o.eo. 7. through 9. (Part of Appendix A) 10. through 13. (Part of Appendix B) * TABLES I. Manualpreloading methods for bolts; accuracy and relative costs .*

    12、 . II. (Part of Appendix B) A. Bolted joint behavior under applied load B. Bolt torque-tension relation pag13 - 5 8 9 11 13 13 21 I22 25 I 26 I 29 12 - 28 19 24 iV Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-HDBK-60 TH W 7777770 0054368 I MIL

    13、-HDBK-60 1. SCOPE 1.1 Scope. This document provides guidelines for the specification of proper bolt preloads and the selection of preload application methods. These guidelines may be used where no rules have been mandated either contractually or otherwise. Provided by IHSNot for ResaleNo reproductio

    14、n or networking permitted without license from IHS-,-,-MIL-HDBK-60 TH 7777770 005LI3b7 3 MIL-HDBK- 60 2. AI?PLIcABU mNTs 2.1 Government documents. Unless otherwise specified, the following smcifications, standards and handbooks of the issue listed in the latest issue o? the Department of Defense Ind

    15、ex of Specifications and Standards (DoDISS) are applicable to this document to the extent noted herein. MILITAFU SPECIFICATION MIL-S-8879 - Screw Threads, Controlled Radius Rmt with Increased Minor Diamter; General Specification for ETDERAI; STANDARD FE;D-STD-H28/1 - Screw-Thread Standards for Feder

    16、al Services Section 1, Nomenclature, Definitions and Letter Symbols for Screw Threads MILITARY HANDBOOK MIL-HD3I-5 - Metallic Materials and Elements for Aerospace Vehicle Structures (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available frc

    17、m the Naval Publications and Forms Center, AT“: NPODS, 5801 Tabor Avenue, Philadelphia, PA.19120-5099.) 2.2 ether publications. None. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-HDBK-60 TH 9977970 005Li370 T MIL-HI=BK-60 3. DEFINITIONS 3.1

    18、Screw thread definitions and symbols follow FED-STD-H28/1. Definitions and symbols for metallic material physical properties follow MIL-HDBK-5. Specific symbols used are defined in the applicable sections of this document. 3.2 Metric measurement units are shown in parenthesis after their respective

    19、inch-pound measurement units. 3.3 The term “bolt“ is used for bolts, screws and studs in this document. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I_ - - -_ MIL-HDBK-bO TH 7797770 005q37L I MIL-HDBK-60 4. GENERAC INFOIIMATICN ON PHELOADS 4.1 P

    20、reload for bolts in axial loaded joints. As a general rule, applied bolt preroad should be sufficient to maintain joint members in contact and in compression. Loss of joint compression results in: a. Leakage of pressurized fluids past compression gaskets. b. Fastener loosening. a loss in bolt tensio

    21、n. relatively small number of load applications. Joint load cycles which open the joint, cause Thus, only a minimal preload may remain after a c. F the amount depends upon friction under the bolt head or nut. or eliminated without loss of axial load. This reduces bolt stress which reduces creep and

    22、fatigue. difficult so this method has limited use. Because of the small angles involved, it cannot be used for bolts which are relatively short. equal tension to each of the bolts in a flange joint, particularly if the joint includes a gasket. Unequal tension will result in leakage past the gasket.

    23、The recommended procedure is to tighten in stages, following a pattern of tightening a pair of opposite bolts, then a pair of opposite bolts 90 away, followed by pairs of opposite bolts in between. An example of the order of tightening pairs of bolts is shown in figure 4. After tightening fully, a r

    24、e- tightening several hours later will help to assure preload relaxation will not cause the joint to leak. if a compressed gasket is not used for sealing. Some of this With controlled back-turning, the torsional load may be reduced Calculation and control of the back-turn angle are 5.7 Flange joint

    25、bolt tensioninq. It is important to apply approximately Following the above procedure is good practice even 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-HDBK-bO TH 9999970 0054378 4 MIL-HDBK-60 Order of tightening: Pair of bolts in position

    26、 1, Pair of bolts in position 2, Pair of bolts in position- FIGURE 4. Example of tightening order for pairs of flange bolts. 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-HDBK-60 TH = 9797970 0054379 6 MIL-HDBK-60 6. METHOD3 FOR CUWROLLLING

    27、BOLT TENCION 6.1 Controlling bolt tension - qeneral. The following are methods used for mntrollina initial bolt tension. There are other methods used which are not included accuracy and relative costs (courtesy of SPC Tec.mologies, Inc.) Preload Method Feel Torque wrench Turn of nut Preload indicati

    28、ng washer Sensor wrench (computer controlled) - below yield using turn of nut - yield point sensing Bolt elongation Strain gages ad Accuracy - + 35% - + 10% + 25% 15% - + 15% - + 8% + 1% - + 3-5% .- this is the starting point. Nut turn angle wi-ll be different for each bolt size, length, material an

    29、d thread lead and will vary with the properties of the clamped materials. Unless the deformation of the nut and joint materials under load is negligible compared to that of the bolt, a significant portion of the nut rotation will be absorbed other than in elongation of the bolt. nut turn angle would

    30、 have to be determined empirically using a simulated joint and a tension measuring device as a standard. travel at the speed of sound for the bolt material, to the other end of the bolt, bounce off that end and return to the generator ina certain period of time. speed of sound varies with material,

    31、temperature and stress level. An ultra- sonic control system generates a pulse and measures the tine for the pulse to travel the length of the bolt and return. computes the stress, load or elongation of the bolt at any time by comparing pulse travel time in the-loaded and unstressed conditions. cons

    32、istent results, both ends of the bolt must be finished square to the bolt axis. In such a case, the above formulas will not apply so 6.2.5 Ultrasonic method. Sound pulse generated from one end of a bolt will This th is dependent upon the bolt length and the speed of sound; the Utilizing various inpu

    33、ts the system To obtain 6.2.6 Strain qaqe nsethod. When a thin wire is bonded to a bolt, it stretches as the bolt elongates under load. electrical resistance of the wire which can be measured and correlated with bolt load. of the bolt or on the inside surface of a small axial hole where there is gre

    34、ater protection. a plastic tube which is then bonded to the inside of a small axial hole in the bolt. This stretch causes a change in Strain gage wires or groups of wires may be bonded on the outside Another method uses mounting in recesses on the outside of 14 Provided by IHSNot for ResaleNo reprod

    35、uction or networking permitted without license from IHS-,-,-MIL-HDBK-bo TH 9999970 0054382 b m MIL-HIBK-60 6.3 Direct loadinq. 6.3.1 Jackinq methods. Application of axial load to a bolt may be made using mechanical jacking or jacking powered by air; hydraulic or explosive gas pressure. to specially

    36、designed nuts which incorporate jacking screws or pistons. The elongation of the bolt creates a gap which is filled by turning the nut down snugly or by a shim, spacer or other mechanical device. after this jacking force has been remved. Often, loads are applied to bolt threads extending beyond the

    37、nut or Load is maintained 6.3.2 Heating-temperature control. When a hot bolt and nut in a joint are cooled, the bolt shrinks and tension is developed. used to calculate the temperature necessary to develop the required axial tensile stress in the bolt when the stress is below the elastic limit. The

    38、following formula is Temperature, t = ft + to where ft = Axial tensile stress, psi e = Coefficient of linear thermal to = perating temperature, OF A steel bolt operating at 70% with an ini ia1 axial e = 6.2 x lO-f)J?. - E = Pbdulus of elasticity, psi Ee expansion /OF Example: tensile stres of 40,000

    39、 psi. E = 30 x 10 i psi and t = 40,000 + 70 = 285% (30 x io6) x (6.2 x To provide bolt tension, the bolt and nut would be heated to a anperature slightly higher than the calculated temperature to allow for cooling prior to nut tightening. The nut would be tightened snugly and the assembly allowed to

    40、 cool. This method can only be used where the bolt is accessible for heating and where the heating will not degrade joint material. Accuracy is limited by the ability to control bolt temperature and by any significant deformation of the joint materials. Tension would develop during cooling. 6.3.3 He

    41、atinq - elongation control. Instead of using temperature controls ta set bolt tension as described in 6.3.2, accuracy can be improved by using controlled expansion of the heated bolt. The joint wuld be seated snugly as in 6.2.4 and heat applied to the bolt. When the bolt expansion, as indicated by a

    42、 thickness gage inserted under the nut, is equal to the elongation calcu- lated as in 6.2.1 for the required axial stress, the nut would again be tightened snugly. approximately equal to the desired stress level. preload if there is an appreciable increase in temperature of the joint materials durin

    43、g bolt heating. Upn cooling, the axial expansion in the bolt should be There will be come loss in 15 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-a_ - - - - - - - MIL-HDBK-60 TH m 7997770 0054383 MIL-HIBK- 6 O 6.4 Mechanical effect of load. 6.4.1

    44、Washer or washer-face deformation. a. One device consists of two concentric steel rings sandwiched between two close-tolerance, hardened steel washers. The inner ring is smaller in diameter and higher than the outer ring by a predetermined aniount. preload in the bolt is indicated when the inner rin

    45、g is compressed and yielded, to the pint indicated when the outer ring can no longer be moved freely by means of a pin inserted into one of the peripheral holes. fastener beyond the first indication of correct tension will result in a significant increase in resistance. Additional rotation could res

    46、ult in overtightening. reusable. A known Rotation of the Due to yielding of the inner ring, the washer assembly is not b. Other systems use calibrated deflection of a spring washer or deflection of projections on a washer or the bearing face of the fastener which flatten under axial load. The correc

    47、t preload is indicated by checking the gap uner the bolt head or nut using a feeler gage or spacer which may be an inte- gral part of the joint. c. Still another type of system consists of a washer with either an integral tab or a separate member inserted into a radial groove on the fastener side of

    48、 the washer. Under bolt preload, the tab or insert will deflect away from the joint to give an indication of the load. 6.4.2 - Washer or hex fastener tab fracture. a. A variation of the washer tab or insert system described in 6.4.1 uses fracture of the exposed tab or insert when a predetermined fas

    49、tener load is achieved. b. Another device consists of a tab adhesively bonded to the outer edge of a washer or to one of the vertical faces of a hex nut or bolt head. The bottom surface of the tab is flush with the bearing surface and transmits a shear load to the adhesive as the fastener is tensioned. It


    注意事项

    本文(DLA MIL-HDBK-60-1990 THREADED FASTENERS - TIGHTENING TO PROPER TENSION《由紧到合适张力线状扣件》.pdf)为本站会员(diecharacter305)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开