1、Comments, suggestions, or questions on this document should be addressed to DLA Aviation VEB, 8000 Jefferson Davis Highway, Richmond, VA 23297-5616, or e-mailed to STDZNMGTdla.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST
2、database at https:/assist.daps.dla.mil/. AMSC N/A FSC 6840 METRIC MIL-DTL-44410C 12 June 2012 SUPERSEDING MIL-DTL-44410B 19 May 2006 DETAIL SPECIFICATION INSECT REPELLENT, CLOTHING APPLICATION, INDIVIDUAL DYNAMIC ABSORPTION APPLICATION (IDAA) KIT This specification is approved for use by all Departm
3、ents and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers one type of IDAA kit for the application of a permethrin insect or arthropod repellent to outer clothing. The kit contains two applications: one for a coat and one for a pair of trousers. 2. APPLICABLE DOCU
4、MENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure
5、the completeness of this list, document users are cautioned that they must meet all specified requirements of the documents cited in sections 3 and 4 of this specification, whether or not they are listed. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,
6、-,-MIL-DTL-44410C 2 2.2 Government documents. 2.2.1 Specifications and standards. The following specification and standard form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. FEDERAL S
7、TANDARD FED-STD-595/34094 - Green, Flat or Lusterless DEPARTMENT OF DEFENSE SPECIFICATION MIL-DTL-44411 - Insect Repellent, Permethrin (Copies of these documents are available online at https:/assist.daps.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Phil
8、adelphia, PA 19111-5094.) 2.2.2 Other government publication. The following other government publication forms a part of this document to the extent specified herein. Unless otherwise specified, the issue is that cited in the solicitation or contract. CODE OF FEDERAL REGULATIONS (CFR) 40 CFR 152 - P
9、esticide Registration and Classification Procedures (Copies of this publication are available online at http:/www.gpoaccess.gov/cfr/ or from the U.S. Government Printing Office, P.O. Box 979050, St. Louis, MO 63197-9000.) 2.3 Order of precedence. Unless otherwise noted herein or in the contract, in
10、the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Material. 3.1.1 Kit
11、bag. The kit bag shall be 0.1 millimeter (mm) (4 mil) polyethylene, of a color conforming to FED-STD-595/34094, 19.0 centimeter (cm) (7.5 inches) in length by 11.5 cm (4.5 inches) in width, heat-sealed with an easy-open notch or tear string. The kit bag shall include black printing on one side as sh
12、own in figure 1. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-44410C 3 3.1.2 Treatment bags. The treatment bags shall be flat style made from sheets or rolls and shall be clean and free of extraneous matter. Each bag shall be 0.1 mm (4 mil
13、) polyethylene, of a color conforming to FED-STD-595/34094, 29.2 cm (11.5 inches) in length by 36.2 cm (14.25 inches) in width, with two heat-sealed side seams. Each bag shall provide a zip lock closure along the 36.2 cm side with no overhang lip, and not less than 2.5 cm (1 inch) or more than 3.2 c
14、m (1.25 inches) from the top of the bag. The interlocking seal shall be made by applying pressure with the fingers to the seal area. Each impregnation bag (bag A - coat, and bag B - trousers) shall include the following labels: a. The information and warning label shown in figure 2 on the side oppos
15、ite the zip lock. b. The appropriate directions for use and disposal label (figure 3 or figure 4) on the zip lock side, and parallel with the zip lock. c. The labels shall be black. 3.1.3 Pouch for two bottles. Two bottles shall be placed inside a 0.05 mm (2 mil) polyethylene pouch, of a color confo
16、rming to FED-STD-595/34094, heat-sealed, with an easy-open notch. One side of the pouch shall include the label information shown in figure 5, in black. 3.1.4 Permethrin bottle. The bottle, with a capacity of 10 milliliters (mL), shall be injection molded of a clear, unbreakable material that shall
17、not be adversely affected by the contents. The plastic bottle shall be amber, brown, green, or natural in color and the material from which the bottle is fabricated shall include an ultraviolet light blocker. The oval shaped, flat bottomed bottle shall have a flat, standard, threaded cap with liner
18、that is able to contain the contents without leakage. Threads on the bottle shall have clear, sharp, molded edges, functionally equivalent to machine-cut threads that will retain the cap securely on the bottle. The cap and cap liner shall neither affect, nor be affected by, the intended contents. Th
19、e cap shall be a 10 mL metal foil-lined urea screw cap with a black, gloss finish. Each bottle shall be filled with 9 mL of permethrin (see 3.1.5) and shall be able to withstand temperatures from 57 C (-70 F) to 71 C (160 F) for 90 days without change in liquid content of more than 5.0 percent. The
20、cap shall be furnished with a plastic seal to prevent inadvertent opening or loosening. Each bottle shall have a printed or silk-screened label as shown in figure 6, in black. 3.1.5 Insect repellent. The insect repellent shall conform to MIL-DTL-44411. The insect repellent shall be furnished in bott
21、les as specified in 3.1.4. 3.1.6 String. Two pieces of 8-ply string, 60 cm (24 inches) long, and of a color conforming to FED-STD-595/34094, shall be included to be used as ties for the garments. 3.1.7 Marking pen. The marking pen (see 5.1.1) is used to mark the garments after treatment. The marking
22、 pen ink shall be black and withstand both dry cleaning and laundering. The pen shall have sufficient ink to mark 12 sets (coat and trousers) of military service field uniforms as specified in figure 3 and figure 4. Provided by IHSNot for ResaleNo reproduction or networking permitted without license
23、 from IHS-,-,-MIL-DTL-44410C 4 3.1.8 Gloves. One pair of disposable polyethylene gloves shall be included. The gloves shall be sized extra-large and shall fit either hand. 3.2 Assembly of kit. One treatment bag A, one treatment bag B, one pouch containing two bottles of repellent, two strings, and o
24、ne pair of gloves shall be placed in each kit bag. The kit bag shall be closed by heat sealing. 3.3 Labeling. Labeling shall be in compliance with the requirements of 40 CFR 152 of the Federal Insecticide, Fungicide, and Rodenticide Act, as amended. Labels shall be approved by the Pesticide Registra
25、tion Division of the Environmental Protection Agency (EPA). 3.4 Workmanship. The end items shall conform to the quality of product established by this specification. 3.5 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should
26、be used to the maximum extent possible, provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 4. VERIFICATION 4.1 Classification of inspection. The inspection requirements specified herein are classified as
27、conformance inspection (see 4.3). 4.2 Inspection conditions. Unless otherwise specified (see 6.2), all inspections shall be performed on a lot. A lot shall consist of the IDAA kits produced by one manufacturer in no more than 24 hours at one plant from the same materials and under essentially the sa
28、me manufacturing conditions, provided the operation is continuous. 4.3 Conformance inspection. The conformance inspection shall be performed in accordance with the inspection provisions set forth herein. The characteristics shown in 3.1, 3.2, and 3.3, when tested in accordance with 4.4, shall consti
29、tute the minimum inspections to be performed by the supplier prior to government acceptance or rejection by lot. The absence of any inspection requirements in the specification shall not relieve the contractor of the responsibility of assuring that all products or supplies submitted to the governmen
30、t for acceptance comply with all requirements of the contract. Failure of any test by any sample shall be cause for rejection of the lot represented. 4.3.1 Sampling. Unless otherwise specified (see 6.2), sampling shall be conducted in accordance with table I. Provided by IHSNot for ResaleNo reproduc
31、tion or networking permitted without license from IHS-,-,-MIL-DTL-44410C 5 TABLE I. Sampling. Lot quantity Number of samples 2 to 25 2 26 to 150 3 151 to 1,200 5 1,201 to 7,000 8 7,001 to 20,000 10 20,001 to 35,000 15 over 35,000 20 4.4 Test methods and procedures. 4.4.1 Component and material inspe
32、ction. As specified in 4.3, components and materials shall be inspected in accordance with all the requirements of referenced documents unless otherwise excluded, amended, modified, or qualified in this specification or applicable purchase document (see 6.2). 4.4.1.1 Material certification. A certif
33、icate of compliance may be acceptable as evidence that the thickness of the kit bag material meets the requirement of 3.1.1, and the thickness of the treatment bag material meets the requirements of 3.1.2. When certificates of compliance are submitted, the government reserves the right to inspect su
34、ch items to determine the validity of the certification. 4.4.2 In-process examination of components. In-process examinations shall be performed to ensure that the kit bag, treatment bags, filled permethrin bottles, pouch, and tie strings conform to the requirements of 3.1.1 through 3.1.6, with the e
35、xception of thickness of material of the kit bag and treatment bags and final closure of the kit bag. 4.4.2.1 In-process examination of kit bag contents. Prior to final heat-seal closure, every filled kit bag shall be examined for conformance to the content requirement in 3.2. Any bag missing a comp
36、onent or not having the correct number of components shall be rejected. 4.4.3 Unit packaging examination. The unit packaged end items shall be examined for the defects listed in table II. Sampling shall be conducted in accordance with table I. Failure of any test by any sample shall be cause for rej
37、ection of the lot represented. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-44410C 6 TABLE II. Visual examination. Examine Defect Marking Omitted; incorrect; illegible; of improper size1, location, sequence, or method of application. Mater
38、ials Any component missing, damaged, or not as specified. Workmanship Inadequate application of components, such as incomplete sealing or closure. Bulged or distorted container. Content Each unit pack in the sample shall be examined for content in accordance with the requirements of 5.1.1. Number pe
39、r unit pack is more or less than required. 1 Proper size will be determined by legibility and completeness of EPA-approved labeling. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel i
40、s to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency,
41、 or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 5.1.1 Unit pack. Twelve kits and three marking pens (see
42、3.1.7) shall be unit packed. 6. NOTES (This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 6.1 Intended use. The insect repellent kit covered by this specification is intended for use in treatment of the military service field uniform to p
43、rovide protection from bites of arthropods (fleas, lice, chiggers, mosquitoes, ticks, scorpions, etc.) and other biting insects. 6.1.1 Guidance on use. Per Natick Soldier Research Center, IDAA application of permethrin is approved only for the following uniform types: a. Marines Battle Dress Uniform
44、 (BDU) b. Navy BDU (tropical and temperate weight) and Desert Camouflage Uniform (DCU) c. Air Force BDU d. Army BDU (tropical and temperate weight), DCU and Army Combat Uniform (ACU) Additional styles may be under evaluation but are not approved as of the date of this document. Provided by IHSNot fo
45、r ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-44410C 7 6.2 Acquisition requirements. Acquisition documents should specify the following: a. Title, number, and date of this specification. b. The specific issue of individual documents referenced (see 2.2.1 and 2.
46、2.2). c. Inspection conditions, if different (see 4.2). d. Sampling, if different (see 4.3.1). e. Component and material inspection, if different (see 4.4.1). f. Packaging requirements (see 5.1). 6.3 Treatment life span. One treatment should last the lifetime of the uniform (approximately 50 launder
47、ings). 6.4 Subject term (key word) listing. Arthropod Battle dress Blouse Coat Combat uniform Field uniform Flea Insecticide Jacket Lice Outer clothing Pants Permethrin Pesticide Pyrethroid Pyrethrum Tick Treatment Trousers 6.5 Changes from previous issue. Marginal notations are not used in this rev
48、ision to identify changes with respect to the previous issue due to the extent of the changes. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-44410C 8 FIGURE 1. Outer kit bag label. INSECT/ARTHROPOD REPELLENT PROTECTIVE TREATMENT FOR MILITAR
49、Y SERVICE FIELD UNIFORM OR EQUIVALENT THAT IS APPROVED FOR TREATMENT WITH IDA KIT NSN 6840-01-345-0237 Military Specification MIL-DTL-44410A EPA Reg. No. 63120-3 EPA Est. No. NET CONTENTS: 0.3 fluid oz (9 ml) per bottle (2 bottles per package) TREATMENT OF MILITARY SERVICE FIELD UNIFORM PROVIDES PROTECTION FROM BITES OF MOSQUITOES, TICKS, CHIGGERS AND H
