1、AMSC N/A FSC 5985 MIL-DTL-3922/60D 23 July 2013 SUPERSEDING MIL-DTL-3922/60C 27 May 2008 DETAIL SPECIFICATION SHEET FLANGES, WAVEGUIDE (CHOKE) (ROUND, 6 HOLE) This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the flang
2、es described herein shall consist of this document and MIL-DTL 3922. FIGURE 1. Flange configuration. INCH-POUND INACTIVE FOR NEW DESIGN AFTER 18 SEPTEMBER 1998 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3922/60D 2 NOTES: 1. Dimensions ar
3、e in inches. 2. Metric equivalents (to the nearest 0.01 mm) are given for general information only and are based upon 1.00 inch = 25.4 mm. 3. Metric equivalents are in parentheses. 4. Roughness of mating surfaces, including seal groove, shall not exceed 63 microinches in accordance with ASME-B46.1,
4、except that flaws shall be included in the roughness height measurement. FIGURE 1. Flange configuration - Continued. Inches mm .002 0.05 .003 0.08 .004 0.10 .005 0.13 .015 0.41 .094 2.39 .250 6.35 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-D
5、TL-3922/60D 3 TABLE I. Dash number and dimensions. PIN M3922/60- 1/ Dimensions Dash no. Used with A +.004 (0.10) B +.004 (0.10) C .015 (0.38) D BSC E Max F G .015 (0.38) H .015 (0.38) J .015 (0.38) Waveguide M85/1- Mating flange M3922/62- 001 2/ 067 001 1.372 .622 3.125 2.750 .016 .190-32 2.000 .250
6、 .750 002 3/ 065 002 (34.85) (15.80) (79.38) (69.85) (0.41) UNF-2B (50.80) (6.35) (19.05) Dash no. Dimensions - Continued. 1/ K .015 (0.38) L +.003 (0.08) -.000 M .005 (0.13) N .003 (0.08) P .005 (0.13) Q +.001 (0.3) R .003 (0.08) S .005 (0.14) T .005 (0.13) 001 2/ 1.750 1.503 .188 1.598 .500 .017 1
7、.860 2.380 .105 002 3/ (44.45) (38.17) (4.78) (40.59) (12.70) (0.43) (47.24) (60.45) (2.67) 1/ Dimensions are in inches (millimeters are in parentheses). Dimensions are in accordance with ASME-Y14.5M. 2/ Copper alloy. 3/ Aluminum alloy. Dash no. Dimensions - Continued. 1/ U .003 (0.08) V .015 (0.38)
8、 W .015 (0.38) Y +.003 (0.08) Z .005 (0.13) 001 3/ .405 .500 1.000 .753 .040 002 2/ (10.29) (12.70) (25.40) (19.13) (1.02) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3922/60D 4 NOTES: 1. Dimensions are in inches. Dimensions are in accord
9、ance with ASME-Y14.5M. 2. Metric equivalents (to the nearest 0.01 mm) are given for general information only and are based upon 1.00 inch = 25.4 mm. 3. Gasket used with flanges M3922/60-001 and M3922/60-002. 4. Formerly MS PIN MS90064-15. FIGURE 2. Gasket dimensions and configuration. TABLE II. Mate
10、rials supplied with flange. Item Description Quantity Gasket - - - - - - - - - - - - - - - - - - - - - - - - Socket-head cap screw - - - - - - - - - - - - Lockwasher - - - - - - - - - - - - - - - - - - - - Silicone rubber (see figure 2) 190-32, UNF-2A, .625 (15.88) long #10-.047 (1.19) thick 1 6 6 I
11、nches mm .004 .010 .139 2.109 0.10 0.25 3.53 53.57 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3922/60D 5 REQUIREMENTS: Dimensions and configuration. Flange: See figure 1 and table I. Gasket: See figure 2. Material: Metallic alloy as spec
12、ified in table I. Marking: See figure 1. Part or Identifying Number (PIN): M3922/60- (and PIN from table I). Materials supplied with flange: See table II. TABLE III. Cross-reference and engineering information. PIN M3922/60- AN nomenclature Frequency range (GHz) 001 002 UG-343B/U UG-440B/U 5.85-8.20
13、 5.85-8.20 Referenced documents. In addition to MIL-DTL-3922, this specification sheet references the following documents: ASME B46.1 ASME-Y14.5M Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Custodians: Prep
14、aring activity: Army - CR DLA - CC Navy - EC Air Force - 85 (Project 5985-2013-035) DLA - CC Review activities: Army - AV, MI Navy - AS, MC, OS, SH Air Force - 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
