欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    DLA MIL-DTL-24251 F-2013 SHIELDS RETAINERS (BASES) AND ADAPTERS ELECTRON TUBE HEAT DISSIPATING.pdf

    • 资源ID:690182       资源大小:174.66KB        全文页数:16页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    DLA MIL-DTL-24251 F-2013 SHIELDS RETAINERS (BASES) AND ADAPTERS ELECTRON TUBE HEAT DISSIPATING.pdf

    1、AMSC N/A FSC 5960 INCH-POUND MIL-DTL-24251F 11 July 2013 SUPERSEDING MIL-DTL-24251E 15 February 2008 DETAIL SPECIFICATION SHIELDS, RETAINERS (BASES), AND ADAPTERS, ELECTRON TUBE, HEAT DISSIPATING GENERAL SPECIFICATION FOR This specification is approved for use by all Departments and Agencies of the

    2、Department of Defense. 1. SCOPE 1.1 Scope. This specification covers the general requirements for heat dissipating electron tube shields, associated retainer (bases), and adapters for use in electronic equipment (see 6.1). 1.2 Part or Identifying Number (PIN). The PIN (when applicable) consists of t

    3、he letter M, the basic number of the specification sheet, and an assigned dash number (see 3.1), as shown in the following example: M24251 /XX -XXXX Designator Specification Dash number sheet number (See specification sheet) 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section a

    4、re specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are caution

    5、ed that they must meet all specified requirements documents cited in sections 3 and 4 of this specification, whether or not they are listed. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified her

    6、ein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract (see 6.2). DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-DTL-12883 - Sockets and Accessories for Plug-in Electronic Components, General Specification for. MIL-DTL-24251/3 - Shield, Electron Tube

    7、, Heat Dissipating, 7 and 9 Pin, Miniature (Split Shell) (Inactive for New Design) MIL-DTL-24251/4 - Retainer (Base), and Adapter, Electron Tube, Heat Dissipating, 7 and 9 Pin, Miniature MIL-DTL-24251/5 - Shield, Electron Tube, Heat Dissipating, 7 and 9 Pin, Miniature (Open Sides) MIL-DTL-24251/6 -

    8、Shield, Electron Tube, Heat Dissipating 7 and 9 Pin, Miniature (Retrofit Type Only) Comments, suggestions, or questions on this document should be addressed to DLA Land and Maritime, ATTN: VAT, P.O. Box 3990, Columbus, OH 43218-3990, or to TubesAmpsdla.mil. Since contact information can change, you

    9、may want to verify the currency of this address information using the ASSIST Online database at https:/assist.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24251F 2 DEPARTMENT OF DEFENSE STANDARDS MIL-STD-130 - Identification Mark

    10、ing of U.S. Military Property. MIL-STD-202 - Electronic and Electrical Component Parts. MIL-STD-889 - Dissimilar Metals MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Copies of these documents are available online at http:/quicksearch.dla.mil/ or https:/assist.dla.mil/ or from the Stand

    11、ardization Document Order Desk), 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solic

    12、itation or contract. AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) ASTM-A342/A342M - Materials, Feebly Magnetic, Permeability of. Standard Test Methods For (Applications for copies can be found online at http:/www.astm.org/ or should be addressed to the American Society for Testing and Materials

    13、 (ASTM), 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.) ELECTRONIC COMPONENTS ASSOCIATION (ECA) ECA-RS209 - Electron Tubes. (Copies of these documents are available online at http:/ or Global Engineering Documents, Attn: Customer Service Department, 15 Inverness Way East, Englewood, CO 80

    14、112-5776.) NATIONAL CONFERENCE OF STANDARDS LABS (NCSL) NCSL-Z540.3 - Requirements for Calibration of Measuring and Test Equipment. (Applications for copies can be found online at http:/www.ncsli.org or should be addressed to the National Conference of Standards Labs (NCSL), 1800 30th Street, Suite

    15、305B, Bolder, CO. 80301.) 2.4 Order of precedence. In the event of a conflict between the text of this document and the references cited herein (except for related specification sheets), the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and reg

    16、ulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Specification sheets. The individual part requirements shall be as specified herein and in accordance with the applicable specification sheet. In the event of any conflict between requirements of this specification and the i

    17、ndividual specification sheet, the latter shall govern. 3.2 Material. The material shall be as specified (see 3.1). When a definite material is not specified, a material shall be used which will enable the tube shields, retainers (bases), and adapters to meet the requirements of this specification.

    18、Acceptance or approval of any constituent material shall not be construed as a guaranty of the acceptance of the finished product. 3.2.1 Dissimilar metals. Where dissimilar metals are used in intimate contact with each other, protection against corrosion shall be provided. Dissimilar metals must be

    19、as recommended in MIL-STD-889. 3.3 Design, construction, and physical dimensions. The tube shields, retainers (bases), and adapters shall be of the design, construction, and physical dimensions specified (see 3.1). The design shields, retainers (bases), and adapters shall be such that they will moun

    20、t to the chassis using the same hardware (including screws), as that of the applicable tube socket. 3.3.1 Finish. Unless otherwise specified (see 3.1), tube shields, retainers (bases), and adapters shall be treated with a black matte finish. That portion of the mating shield and retainer (base) or r

    21、etainer (base) and chassis where low electrical resistance is required may be finished with other than black matte. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24251F 3 3.3.2 Pure tin: The use of pure tin, as an underplate or final finish

    22、, is prohibited both internally and externally. Tin content of electron tube components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.3). 3.3.3 Liners. Shields shall be constructed in such a way that the liners are securely ret

    23、ained in position within the shield (see 3.5.3). Liners with circumferential corrugations or other configurations that could allow tube breakage and that do not permit spring action within the shield to allow for maximum tube diameter variations are not acceptable. 3.3.4 Installation and removal. De

    24、sign of the shield shall be such that installation and removal of the shield from a seated electron tube shall not scratch or damage the electron tube envelope when tested as specified in 4.5.3.4. Unless otherwise specified, no tool shall be required for installation or removal of the shield from th

    25、e tube or retainer (base) or adapter. 3.3.5 Spring retention. When used (see 3.1), the coil spring shall be securely retained within the shield. The free end of the spring, or the loop that makes contact with the electron tube envelope shall be at least seven-eighths of a complete turn and the sprin

    26、g tip shall not touch the tube envelope. 3.3.6 Retainer (base) and adapter. The retainer (base) and adapter design shall be such that it rigidly retains the tube shield during all tests and examination of this specification. 3.4 Permeability. All parts shall be made from materials that are classed a

    27、s nonmagnetic. The permeability of the tube shield assembly shall be less than 2 (air = 1.0) (see 4.5.2). 3.5 Installation, locking and unlocking torque or load, and removal force. 3.5.1 Initial force. The installation, locking and unlocking torque or load, and removal forces necessary to install an

    28、d remove the shield over the applicable slug (see figure 1) and retainer (base), and adapter shall be not greater than specified on the applicable specification sheet (see 3.1), when tested in accordance with 4.5.3.1. 3.5.2 Force at temperature extremes. The installation, locking and unlocking torqu

    29、e or load, and removal force shall be not greater than 150 percent nor less than 50 percent of the initial force when tested at 85C 5C and -55C 5C, in accordance with 4.5.3.2. 3.5.3 Fatigue. When tested in accordance with 4.5.3.3, the installation or removal force shall be not greater than 125 perce

    30、nt nor less than 50 percent of the initial force and the liner shall remain in position within the shield. 3.6 Vibration. When tested in accordance with 4.5.4, the shield shall not loosen from the retainer (base) or adapter. There shall be no evidence of damage to the shield, or retainer (base), and

    31、 adapter, nor the glass envelope of the electron tube, during installation, during the test, or upon removal after the test. 3.7 Shock. When tested in accordance with 4.5.5, the shield shall not loosen from the retainer (base) or adapter as applicable, and there shall be no evidence of damage to the

    32、 shield, tube socket, shield retainer (base), or the glass envelope of the electron tube. 3.8 Heat resistance. When shields, retainers (bases) and adapters are tested in accordance with 4.5.6, there shall be no peeling, blistering, chipping, or pitting of the finish. 3.9 Heat dissipation. The averag

    33、e reduction of a minimum of two surface temperature readings of the instrumented tube shall be not less than the value specified (see 3.1), when tested in accordance with 4.5.7.1. 3.10 Salt atmosphere (corrosion). When shields, retainers (bases) and adapters are tested as specified in 4.5.8, there s

    34、hall be no evidence of corrosion and the finish shall not peel, blister, chip, or pit. 3.11 Electrical contact. The dc resistance from the shield to the chassis shall be not greater than 1 ohm when tested in accordance with 4.5.9. 3.12 Marking. Each tube shield, retainer (base), or adapter shall be

    35、permanently and legibly marked in accordance with MIL-STD-130 with the following: a. Military Part or Identifying Number (PIN). b. Date and source code in accordance with MIL-STD-1285. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24251F 4

    36、3.13 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible, provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantage

    37、ous life cycle costs. 3.14 Workmanship. Shields and associated parts shall be processed in such a manner as to be uniform in quality and shall be free from pits, corrosion, cracks, rough edges, chips, spalls and other defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1

    38、Classification of inspections. The inspection and testing of electron tube shields, retainers(bases) and adapters shall be classified as conformance inspection. a. Inspection conditions (see 4.3). b. Conformance inspection (see 4.4). 4.2 Test equipment and inspection facilities. The contractor shall

    39、 establish and maintain a calibration system in accordance with NCSL-Z540.3. 4.3 Inspection conditions. Unless otherwise specified herein, all inspections shall be made in accordance with the general requirements of MIL-STD-202. 4.4 Conformance inspection. 4.4.1 Inspection of product for delivery. I

    40、nspection of product for delivery shall consist of groups A and B inspection. 4.4.1.1 Inspection lot. An inspection lot shall consist of tube shields, retainers (bases), or adapters of the same design and size, produced under essentially the same conditions and offered for inspection at one time. 4.

    41、4.1.2 Rejected lots. If an inspection lot is rejected, the contractor may rework it to correct the defects, or screen out the defective units, and resubmit for reinspection. Such lots shall be separate from new lots, and shall be clearly identified as reinspected lots. 4.4.1.3 Group A inspection. Gr

    42、oup A inspection shall consist of the inspections specified in table I, in the order shown. TABLE I. Group A inspection. Examination Requirements paragraph Method paragraph Visual and mechanical examination 3.2 through 3.3.5 and 3.13 4.5.1 Provided by IHSNot for ResaleNo reproduction or networking p

    43、ermitted without license from IHS-,-,-MIL-DTL-24251F 5 4.4.1.3.1 Sampling plan. Statistical sampling and inspection shall be performed on an inspection lot basis with a random sample of components selected in accordance with table II. The acceptance levels shall be based upon the zero defective samp

    44、ling plan. No failures shall be permitted. TABLE II. Group A sampling plan. Lot size Sample size 1 - 13 14 - 150 151 - 280 281 - 500 501 - 1,200 1,201 - 3,200 3,201 - 10,000 10,001 - 35,000 35,001 - 150,000 150,001 - 500,000 500,001 and over 100 percent 13 20 29 34 42 50 60 74 90 102 4.4.1.4 Group B

    45、 inspection. Group B inspection shall consist of the inspections specified in table III, in the order shown, and the sample shall be selected from inspection lots that have passed group A inspection. NOTE: If the following group B tests have previously been performed by the tube shield manufacturer,

    46、 and if the material, manufacturing process, and test requirements are the same as when these tests were initially performed, the subject test(s) need not be performed again. TABLE III. Group B inspection. Test Requirement paragraph Method paragraph Heat resistance - - - - - - - - - - - - - - - - -

    47、- - - - - - - - - Heat dissipation - - - - - - - - - - - - - - - - - - - - - - - - - Permeability - - - - - - - - - - - - - - - - - - - - - - - - - - - - Installation and removal - - - - - - - - - - - - - - - - - - - - Salt atmosphere (corrosion) - - - - - - - - - - - - - - - - - Electrical contact

    48、- - - - - - - - - - - - - - - - - - - - - - - - - Installation, locking and unlocking torque or load, and removal force - - - - - - - - - - - - - - - - - - - - - - - Initial force at 25C - - - - - - - - - - - - - - - - - - - - - Force at temperature extremes - - - - - - - - - - - - - Fatigue - - - -

    49、 - - - - - - - - - - - - - - - - - - - - - - - - - - Vibration - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Shock - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3.8 3.9 3.4 3.3.4 3.10 3.11 3.5 3.5.1 3.5.2 3.5.3 3.6 3.7 4.5.6 4.5.7 4.5.2 4.5.3.4 4.5.8 4.5.9 4.5.3 4.5.3.1 4.5.3.2 4.5.3.3 4.5.4 4.5.5 4.4.1.4.1 Sampling plan. Sample units shall be selected from tube shields,


    注意事项

    本文(DLA MIL-DTL-24251 F-2013 SHIELDS RETAINERS (BASES) AND ADAPTERS ELECTRON TUBE HEAT DISSIPATING.pdf)为本站会员(explodesoak291)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开