1、 REVISIONSLTR DESCRIPTION DATE APPROVEDPrepared in accordance with ASME Y14.24 Vendor item drawing REV PAGE REV PAGE REV STATUS OF PAGES REV PAGE 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY RICK OFFICER DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 Original date of drawing YY-MM-DD CH
2、ECKED BY RAJESH PITHADIA TITLE MICROCIRCUIT, LINEAR, PRECISION, LOW POWER INSTRUMENTATION AMPLIFIER, MONOLITHIC SILICON 10-08-11 APPROVED BY CHARLES F. SAFFLE SIZE A CODE IDENT. NO. 16236 DWG NO. V62/10605 REV PAGE 1 OF 12 AMSC N/A 5962-V068-10 Provided by IHSNot for ResaleNo reproduction or network
3、ing permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/10605 REV PAGE 2 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance precision, low power instrumentation amplifier microcircuit, wi
4、th an operating temperature range of -55C to +125C. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturers PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation: V62/10605 -
5、01 X E Drawing Device type Case outline Lead finish number (See 1.2.1) (See 1.2.2) (See 1.2.3) 1.2.1 Device type(s). Device type Generic Circuit function 01 INA129-EP Precision, low power instrumentation amplifier 1.2.2 Case outline(s). The case outline(s) are as specified herein. Outline letter Num
6、ber of pins JEDEC PUB 95 Package style X 8 MS-012-AA Plastic surface mount1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacture: Finish designator Material A Hot solder dip B Tin-lead plateC Gold plateD PalladiumE Gold flash pallad
7、ium Z Other Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/10605 REV PAGE 3 1.3 Absolute maximum ratings. 1/ Supply voltage (VS) . 18 V Analog input voltage range
8、 40 V Output short circuit (to ground) . Continuous Power dissipation (PD) . 166.6 mW Junction temperature range (TJ) 150C Storage temperature range (TSTG) . -55C to +125C Lead temperature (soldering 10 seconds) 300C Thermal resistance, junction to case (JC) . 35.9C/W Thermal resistance, junction to
9、 ambient (JA) 150C/W 1.4 Recommended operating conditions. 2/ Supply voltage range (VS) 15 V Operating free-air temperature range (TA) . -55C to +125C 1/ Stresses beyond those listed under “absolute maximum rating” may cause permanent damage to the device. These are stress ratings only, and function
10、al operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2/ Use of this product beyond the manufacturers design rules o
11、r stated parameters is done at the users risk. The manufacturer and/or distributor maintain no responsibility or liability for product used beyond the stated limits. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLU
12、MBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/10605 REV PAGE 4 2. APPLICABLE DOCUMENTS JEDEC PUB 95 Registered and Standard Outlines for Semiconductor Devices (Applications for copies should be addressed to the Electronic Industries Alliance, 2500 Wilson Boulevard, Arlington, VA 22201-3834 or o
13、nline at http:/www.jedec.org) 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and legibly marked with the manufacturers part number as shown in 6.3 herein and as follows: A. Manufacturers name, CAGE code, or logo B. Pin 1 identifier C. ESDS identification (optional) 3.2 Unit container. The u
14、nit container shall be marked with the manufacturers part number and with items A and C (if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, con
15、struction, and physical dimension. The design, construction, and physical dimensions are as specified herein. 3.5 Diagrams. 3.5.1 Case outline. The case outline shall be as shown in 1.2.2 and figure 1. 3.5.2 Terminal connections. The terminal connections shall be as shown in figure 2. Provided by IH
16、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/10605 REV PAGE 5 TABLE I. Electrical performance characteristics. 1/ Test Symbol Conditions VS= 15 V, RL= 10 k Unless otherwise s
17、pecifiedTemperature, TADevice type Limits Unit Min Max Input section Offset voltage, referred to input (RTI) Initial offset voltage +25C 01 100 800/G V -55C to +125C 150 2050/G Offset voltage versus power supply VS= 2.25 to 18 V +25C 01 1.6 175/G V/V -55C to +125C 1.8 175/G Long term stability +25C
18、01 1 3/G typical V/mo Differential input 2/ impedance +25C 01 1010|2 typical |pF Common mode 2/ input impedance +25C 01 1011|9 typical |pF Common mode 3/ voltage range VO= 0 V +25C 01 (V+) - 2 V (V-) + 2 Safe input voltage +25C 01 40 V Common mode rejection CMR G = 1, VCM= 13 V, RS= 1 k +25C 01 75 d
19、B -55C to +125C 67 G = 10, VCM= 13 V, RS= 1 k +25C 93 -55C to +125C 84 G = 100, VCM= 13 V, RS= 1 k +25C 113 -55C to +125C 98 G = 1000, VCM= 13 V, RS= 1 k +25C 113 -55C to +125C 98 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from
20、 IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/10605 REV PAGE 6 TABLE I. Electrical performance characteristics Continued. 1/ Test Symbol Conditions VS= 15 V, RL= 10 k Unless otherwise specifiedTemperature, TADevice type Limits Unit Min Max Current se
21、ction Bias current IB+25C 01 8 nA -55C to +125C 16 Offset current IOS+25C 01 8 nA -55C to +125C 16 Noise section Noise voltage, VNf = 10 Hz, G = 1000, RS= 0 +25C 01 10 typical nV /Hz referred to input (RTI) f = 100 Hz, G = 1000, RS= 0 8 typical f = 1 kHz, G = 1000, RS= 0 8 typical fB= 0.1 Hz to 10 H
22、z, G = 1000, RS= 0 0.2 typical Vpp Noise current f = 10 Hz, G = 1000, RS= 0 +25C 01 0.9 typical pA /Hz f = 1 kHz, G = 1000, RS= 0 0.3 typical fB= 0.1 Hz to 10 Hz, G = 1000, RS= 0 30 typical pApp Gain section Gain equation +25C 01 1 + (49.4 k/RG) typical V/V Range gain -55C to +125C 01 1 10000 V/V Ga
23、in error G = 1 +25C 01 0.1 % -55C to +125C 0.15 G = 10 +25C 0.5 -55C to +125C 0.65 G = 100 +25C 0.65 -55C to +125C 1.1 G = 1000 +25C 2 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLU
24、MBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/10605 REV PAGE 7 TABLE I. Electrical performance characteristics Continued. 1/ Test Symbol Conditions VS= 15 V, RL= 10 k Unless otherwise specifiedTemperature, TADevice type Limits Unit Min Max Gain section - continued. Gain versus 4/ temperature G
25、= 1 +25C 01 10 ppm / C Gain 49.4 k 4/ 5/ resistance +25C 01 100 ppm / C Nonlinearity G = 1, VO= 13.6 V +25C 01 0.0018 % of FSR -55C to +125C 0.0035 G = 10 +25C 0.0035 -55C to +125C 0.0055 G = 100 +25C 0.0035 -55C to +125C 0.0055 G = 1000 +25C 6/ Output section Positive output voltage +VOUTRL= 10 k +
26、25C 01 (V+) - 1.4 V Negative output voltage -VOUTRL= 10 k +25C 01 (V-) + 1.4 V Load capacitance stability CLS+25C 01 1000 typical pF Short circuit current ISC+25C 01 +6/-15 typical mA Frequency response section Bandwidth, -3 dB G = 1 +25C 01 1300 typical kHz G = 10 700 typical G = 100 200 typical G
27、= 1000 20 typical Slew rate SR VO= 10 V, G = 10 +25C 01 4 typical V/s See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/10605 REV PAGE
28、 8 TABLE I. Electrical performance characteristics Continued. 1/ Test Symbol Conditions VS= 15 V, RL= 10 k Unless otherwise specifiedTemperature, TADevice type Limits Unit Min Max Frequency response section - continued. Settling time, 0.01% tSG = 1 +25C 01 7 typical s G = 10 7 typical G = 100 9 typi
29、cal G = 1000 80 typical Overload recovery 50% overdrive +25C 01 4 typical s Power supply section Voltage range VR+25C 01 2.25 18 V Current, total ITVIN= 0 V +25C 01 750 A -55C to +125C 1200 1/ Testing and other quality control techniques are used to the extent deemed necessary to assure product perf
30、ormance over the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization and/or design. 2/ The | symbolizes
31、 that the input impedance is being represented as the resistance value is in parallel with the capacitance. 3/ Input common mode range varies with output voltage. 4/ Specified by wafer test. 5/ Temperature coefficient of the 49.9 k term in the gain equation. 6/ Nonlinearity measurements in G = 1000
32、are dominated by noise. Typically nonlinearity is 0.001%. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/10605 REV PAGE 9 Case X FIGURE 1. Case outline. Provided
33、by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/10605 REV PAGE 10 Case X - continued Symbol Dimensions Inches Millimeters Min Max Min Max A - 0.069 - 1.75 A1 0.004 0.010 0.
34、10 0.25 b 0.012 0.020 0.31 0.51 c 0.005 0.010 0.17 0.25 D 0.189 0.197 4.80 5.00 E 0.150 0.157 3.80 4.00 E1 0.228 0.244 5.80 6.20 e 0.050 BSC 1.27 BSC L 0.016 0.050 0.40 1.27 n 8 8 NOTES: 1. Controlling dimensions are inch, millimeter dimensions are given for reference only. 2. For dimension D, body
35、length does not include mold flash, protrusion, or gate burrs. Mold flash, protrusion, or gate burrs shall not exceed 0.006 inch (0.15 mm) per end. 3. For dimension E, body width does not include interlead flash. Interlead flash shall not exceed 0.017 inch (0.43 mm) per side. 4. Falls within JEDEC M
36、S-012-AA. FIGURE 1. Case outline Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/10605 REV PAGE 11 Device type 01 Case outline X Terminal number Termina
37、l symbol Description 1 RGSingle external resistor used to set gain 2 -VINNegative input voltage 3 +VINPositive input voltage 4 -VSNegative supply voltage 5 REF Output reference 6 VOOutput voltage 7 +VSPositive supply voltage 8 RGSingle external resistor used to set gain FIGURE 2. Terminal connection
38、s. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/10605 REV PAGE 12 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for perfor
39、ming all inspection and test requirements as indicated in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices, classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging.
40、Preservation, packaging, labeling, and marking shall be in accordance with the manufacturers standard commercial practices for electrostatic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration con
41、trol. The data contained herein is based on the salient characteristics of the device manufacturers data book. The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the su
42、ggested source(s) of supply herein is not to be construed as a guarantee of present or continued availability as a source of supply for the item. Vendor item drawing administrative control number 1/ Device manufacturer CAGE code Top side marking 2/ 3/ Vendor part number V62/10605-01XE 01295 129EP IN
43、A129MDREP 1/ The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation. 2/ For the most current package and ordering information, see the package option addendum at the end of the manufacturers data sheet , or use website . 3/ Pack
44、age drawings, standard packaging quantities, thermal data, symbolization, and printed circuit board (PCB) design guidelines are available at CAGE code Source of supply 01295 Texas Instruments, Inc. Semiconductor Group8505 Forest Lane P.O. Box 660199 Dallas, TX 75243 Point of contact: U.S. Highway 75 South P.O. Box 84, M/S 853 Sherman, TX 75090-9493 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
