1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Add new source of supply; change temperature coefficient of schematics 6 and 14. Editorial changes throughout. 20 May 88 D. MOORE B Changes in accordance with NOR 5905-R010-93. 28 May 93 D. MOORE C Update and validation of drawing. Editorial changes through
2、out. 11Sep 00 K. COTTONGIM D Add pure tin prohibition paragraph. Editorial changes throughout. 29 Jan 07 M. RADECKI CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 Prepared in accordance with ASME Y14.100 Selected item drawin
3、g REV D D PAGE 18 19 REV STATUS OF PAGES REV D D D D D D D D D D D D D D D D D PAGES 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17PMIC N/A PREPARED BY Alan R. Knox DESIGN ACTIVITY: DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO 45444-5000 Original date of drawing: CHECKED BY David W. Withrow TITLE RESIST
4、OR NETWORK, FIXED, FILM, 10-PIN SIP, MULTIPLE RESISTANCE VALUES, MULTIPLE 29 December 1987 APPROVED BY David E. Moore SCHEMATICS, (LOW PROFILE) SIZE A CODE IDENT. NO. 14933 DWG NO. 87071 REV D PAGE 1 OF 19 AMSC N/A 5905-E624 Provided by IHSNot for ResaleNo reproduction or networking permitted withou
5、t license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87071 REV D PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a 10-pin, low profile, single-in-line package (SIP), fixed film, resistor network. 1.2 Part or Identifying Numbe
6、r (PIN). The complete PIN is as follows: 87071 - 01 Drawing number Schematic number (see figure 2) 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent speci
7、fied herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-83401 - Resistor Networks, Fixed, Film, and Capacitor-Resistor Networks, Ceramic Capacitor and Fixed Film Resistors, General Specificat
8、ion for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D,
9、 Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, (except for related associated detail specifications, specification sheets, or MS standards), the text of this document takes precedence. Nothing in t
10、his document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item Requirements. The individual item requirements shall be in accordance with MIL-PRF-83401 and as specified herein. 3.2 Interface and physical dimensions. The resis
11、tor shall meet the interface and physical dimensions as specified in MIL-PRF-83401 and herein (see figure 1). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87071 REV
12、D PAGE 3 Inches mm Inches mm Inches mm 0.002 0.05 0.019 0.48 0.125 3.17 0.005 0.006 0.12 0.15 0.098 0.100 2.48 2.54 0.200 1.000 5.08 25.40 0.010 0.25 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, dimensional tolerance
13、s shall be 0.02 (0.5 mm) for two decimal places and 0.010 (0.25 mm) for three decimal places. 4. The picturization of the styles above is given as representative of the envelope of the item. Slight deviations from the outline shown, which are contained within the envelope and do not alter the functi
14、onal aspects of the device, are acceptable. FIGURE 1. Resistor network. 3.3 Electrical characteristics. 3.3.1 Resistance. The resistance value shall be as specified on figure 2. 3.3.2 Resistance tolerance. The resistance tolerance shall as specified on figure 2. 3.3.3 Resistor power rating. The resi
15、stor power rating for individual resistors shall be 125 milliwatts maximum at 70oC derated to 0 watts at 150oC. 3.3.4 Package power rating. The package power rating shall not exceed the sum of the individual resistance element power rating in the network. 3.3.5 Operating voltage. Each resistor eleme
16、nt shall have a maximum operating voltage of 100 V dc or ac rms. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87071 REV D PAGE 4 3.3.6 Schematic. Resistor networks a
17、re available in schematics listed on figure 2. 3.3.7 Resistance temperature characteristic. Unless otherwise specified, the resistance temperature characteristic shall be 100 ppm/oC. 3.4 Characteristic. The characteristic shall be in accordance with MIL-PRF-83401, characteristic K. 3.5 Pure tin. The
18、 use of pure tin, as an underplate or final finish is prohibited both internally and externally. Tin content of resistor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.4). 3.6 Environmental requirements. The environme
19、ntal requirements shall be in accordance with MIL-PRF-83401, characteristic K. 3.7 Marking. Marking shall be in accordance with MIL-STD-1285, except the PIN shall be as specified in 1.2, with the manufacturers CAGE number or trade mark and date code. 3.8 Recycled, recovered, or environmentally prefe
20、rable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.9 Certificate of compliance
21、. A certificate of compliance shall be required from manufacturers requesting to be listed as a suggested source of supply. 3.10 Workmanship. Resistors shall be uniform in quality and free from any defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Qualification inspec
22、tion. Qualification inspection is not applicable to this document. 4.2 Conformance inspections. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of group A and group B inspections of MIL-PRF-83401. 4.2.2 Certification. The acquiring activity, at its discreti
23、on, may accept a certificate of compliance with group B requirements in lieu of performing group B tests (see 6.2d). 4.3 Inspection of packaging. Inspection of packaging shall be in accordance with MIL-PRF-83401. 4.4 Visual and mechanical examination. Resistors shall be examined to verify that the m
24、aterials, design, construction, physical dimensions, marking, and workmanship are in accordance with the applicable requirements of MIL-PRF-83401. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging
25、 of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or D
26、efense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. Provided by IHSNot for ResaleNo reproductio
27、n or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87071 REV D PAGE 5 NOTES: 1. Resistance tolerance for shall be 2 percent, except for R9 which shall be 10 percent. 2. R1 through R8 resistor temperature coefficien
28、t tracking shall be 50 ppm/oC maximum. 3. k = kilohms, M = megohms. NOTES: 1. Resistance tolerance for shall be 2 percent. 2. R1 through R7 resistor temperature coefficient tracking shall be 50 ppm/oC maximum. 3. k = kilohms. FIGURE 2. Schematic, resistance and tolerance. Provided by IHSNot for Resa
29、leNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87071 REV D PAGE 6 NOTES: 1. Resistance tolerance for shall be 2 percent. 2. R2 through R6 resistor temperature coefficient tracking shall be 50 pp
30、m/oC maximum. 3. k = kilohms. NOTES: 1. Resistance tolerance for R1 and R2 shall be 2 percent. R3 and R4 shall be 1 percent. R5 through R8 shall be 20 percent 2. Resistor temperature coefficient for R1 through R5 shall be 100 ppm/oC maximum. R6 through R8 shall be 200 ppm/oC. 3. Resistor temperature
31、 coefficient tracking for R1 through R5 shall be 50 ppm/oC maximum 4. k = kilohms, M = megohms. FIGURE 2. Schematic, resistance and tolerance - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO S
32、IZE A CODE IDENT NO. 14933 DWG NO. 87071 REV D PAGE 7 NOTES: 1. Resistance tolerance for R1, R2 and R8 shall be 1 percent. R3 through R7 shall be 2 percent. 2. Resistor temperature coefficient for R1, R3, R4, R6 and R7 shall be 100 ppm/oC maximum. R2, R5, and R8 shall be 200 ppm/oC. 3. Resistor temp
33、erature coefficient tracking for R1 through R5 and R8 shall be 50 ppm/oC maximum 4. k = kilohms, M = kilohms. NOTES: 1. Resistance tolerance for shall be 1 percent. 2. Resistor temperature coefficient shall be 100 ppm/oC maximum. 3. = ohms, k = kilohms. FIGURE 2. Schematic, resistance and tolerance
34、- Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87071 REV D PAGE 8 NOTES: 1. Resistance tolerance shall be 3 percent. 2. Resistor temperature coefficient s
35、hall be 200 ppm/oC. 3. Power rating shall be 20 mW at +120oC. 4. k = kilohms. NOTES: 1. Resistance tolerance shall be 3 percent. 2. Resistor temperature coefficient shall be 200 ppm/oC maximum. 3. R3 power rating shall be 40 mW at +120oC. R1, R2, R4 through R9 power ratings shall be 25 mW at +120oC.
36、 4. = ohms, k = kilohms. FIGURE 2. Schematic, resistance and tolerance - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87071 REV D PAGE 9 NOTES: 1. Resista
37、nce tolerance shall be 1 percent. 2. Resistor temperature coefficient shall be 200 ppm/oC maximum. 3. k = kilohms. NOTES: 1. Resistance tolerance shall be 3 percent. 2. Resistor temperature coefficient shall be 200 ppm/oC maximum. 3. R2 and R3 power rating shall be 60 mW at +120oC. R1, R4 through R6
38、 power ratings shall be 25 mW at +120oC. 4. = ohms, k = kilohms. FIGURE 2. Schematic, resistance and tolerance - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG
39、NO. 87071 REV D PAGE 10 NOTES: 1. Resistance tolerance shall be 3 percent. 2. Resistor temperature coefficient shall be 200 ppm/oC maximum. 3. = ohms, k = kilohms. NOTES: 1. Resistance tolerance shall be 3 percent. 2. Resistor temperature coefficient shall be 200 ppm/oC maximum. 3. R1 and R5 power r
40、ating shall be 60 mW at +120oC. R2, R3, R4, R6, R7, and R8 power ratings shall be 25 mW at +120oC. 4. = ohms, k = kilohms. FIGURE 2. Schematic, resistance and tolerance - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC S
41、UPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87071 REV D PAGE 11 NOTES: 1. Resistance tolerance shall be 3 percent. 2. Resistor temperature coefficient shall be 200 ppm/oC maximum. 3. R3 power rating shall be 40 mW at +120oC. R1, R2, R4, through R9 power ratings shall be 25 mW at +1
42、20oC. 4. = ohms, k = kilohms. NOTES: 1. Resistance tolerance shall be 1 percent. 2. Resistor temperature coefficient shall be 100 ppm/oC maximum. 3. k = kilohms. FIGURE 2. Schematic, resistance and tolerance - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without li
43、cense from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87071 REV D PAGE 12 NOTES: 1. Resistance tolerance for R1, R2 and R8 shall be 1 percent. R3 through R7 shall be 2 percent. 2. Resistor temperature coefficient for R1, R3, R4, R6 and R7 shall be 100 p
44、pm/oC maximum. R2, R5, and R8 shall be 200 ppm/oC. 3. Resistor temperature coefficient tracking shall be 50 ppm/oC maximum 4. k = kilohms, M = kilohms. NOTES: 1. Resistance tolerance shall be 3 percent. 2. Resistor temperature coefficient shall be 200 ppm/oC maximum. 3. R1, R2, R3, R5, R7 and R9 pow
45、er rating shall be 40 mW at +120oC. R4, R6, and R8 power ratings shall be 130 mW at +120oC. 4. k = kilohms. FIGURE 2. Schematic, resistance and tolerance - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DA
46、YTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87071 REV D PAGE 13 NOTES: 1. Resistance tolerance shall be 3 percent. 2. Resistor temperature coefficient shall be 200 ppm/oC maximum. 3. k = kilohms. NOTES: 1. Resistance tolerance shall be 3 percent. 2. Resistor temperature coefficient shall be 200 p
47、pm/oC maximum. 3. = ohms, k = kilohms. FIGURE 2. Schematic, resistance and tolerance - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87071 REV D PAGE 14 NO
48、TES: 1. Resistance tolerance shall be 2 percent. 2. Resistor temperature coefficient shall be 200 ppm/oC maximum. 3. Power rating shall be 25 mW at +120oC. 4. = ohms, k = kilohms. NOTES: 1. Resistance tolerance shall be 3 percent. 2. Resistor temperature coefficient shall be 200 ppm/oC maximum. 3. R3, and R6 power rating shall be 60 mW at +12
