1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Revised case design and electrical characteristics to conform to MIL-PRF-83532. Updated vendor table. 29 SEP 1987 Randy Larson B Changed footnote on page 5. Added vendor. Expanded information in 6.3. 7 JUL 1988 Randy Larson C Added two dash numbers (-12 and
2、 -13) and one vendor. Changed rise time requirement in 3.9. Editorial changes throughout. 27 SEP 1989 Randy Larson D Renumbered pins and added top view to figure 1. Added 3.25. Editorial changes throughout. 29 OCT 1991 David Moore E Added 3.3.3 and 6.3. Added note 6 to figure 1. Changed 1.2, 3.3.2,
3、4.1.1, and 6.2. Editorial changes throughout. 5 Jan 1993 David Moore F Validation and update. 6 May 2006 Kendall Cottongim G Performed editorial and boilerplate updates. 19 Jun 2008 Michael A. Radecki Prepared in accordance with ASME Y14.100 Source control drawing REV G G G G G G G G G REV STATUS OF
4、 PAGES PAGES 1 2 3 4 5 6 7 8 9 PMIC N/A PREPARED BY Randy Larson DESIGN ACTIVITY DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444-5000 CHECKED BY Randy Larson APPROVED BY Ivan R. Jones TITLE DELAY LINE, ACTIVE, 10 TAPS, 14 PIN DIP, TTL INTERFACED SIZE A CODE IDENT. NO. 14933 DWG NO. 85014 Original
5、 date of drawing 30 Aug 85 REV G PAGE 1 OF 9 AMSC N/A 5999-E213CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-CODE IDENT NO. 14
6、933 DWG NO. 85014 DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A REV G SHEET 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a family of TTL interfaced active delay lines with 14 pins and 10 taps. 1.2 Part or Identifying Number (PIN). The DESC drawing PIN shall be as shown i
7、n the following example: 85014 -01 C Drawing number Dash number Inspection option A or C (see table I) (see 4.1.1) 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other
8、 sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents in sections 3 and 4 of this specification, whet
9、her or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the s
10、olicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-DTL-31000 - Technical Data Packages. MIL-PRF-38535 - Integrated Circuits (Microcircuits) Manufacturing, General Specification For. MIL-PRF-83532 - Delay Lines, Active, General Specification for. DEPARTMENT OF DEFENSE STANDARD MIL-STD-
11、883 - Microcircuits. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Order of precedence. In the event of a conf
12、lict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensions. This
13、 drawing shall be interpreted in accordance with MIL-DTL-31000. 3.2 Materials. 3.2.1 Case. Case material shall be molded or encapsulated epoxy and shall conform to MIL-PRF-83532. 3.2.2 Terminals. Terminal material and finish shall be in accordance with MIL-PRF-38535. Provided by IHSNot for ResaleNo
14、reproduction or networking permitted without license from IHS-,-,-CODE IDENT NO. 14933 DWG NO. 85014 DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A REV G SHEET 3 Inches mm .002 0.05 .010 0.25 .015 0.38 .020 0.51 .050 1.27 .060 1.52 .070 1.78 .100 2.54 .125 3.18 .265 6.73 .300 7.62 .315 8.00 .
15、450 11.43 .600 15.24 .800 20.32 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are for general information only. 3. Unless otherwise specified, tolerance is .005 (0.13 mm). 4. Pin number 2 is not connected and may be omitted at the manufacturers option. 5. Location and shape of standoffs
16、are optional. Height shall be as indicated. 6. Leads shall be free of case meniscus and other foreign material and shall be solderable for a minimum of .010 inch (0.25 mm) above the seating plane of the delay line. FIGURE 1. Design, construction, and dimensions. Provided by IHSNot for ResaleNo repro
17、duction or networking permitted without license from IHS-,-,-CODE IDENT NO. 14933 DWG NO. 85014 DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A REV G SHEET 4 3.2.3 Microcircuits. Microcircuits shall meet the requirements of MIL-STD-883, level B (minimum). 3.3 Design, construction, and dimensio
18、ns. See figure 1. 3.4 PINs. See table II. 3.5 Delay time. Delay time from input to all taps shall be as specified in tables I and II. 3.6 Delay time variation with temperature. See tables I and II. 3.7 Delay tolerance. See tables I and II. 3.8 Rise time (applied to leading edge only). Rise time shal
19、l be 4 nanoseconds (ns) maximum for dash numbers -01 through -11. Rise time shall be 5 ns maximum for dash numbers -12 and -13. Conditions (TC-55C to +125C): VCC= 5.0 V; TRI 3 ns; CL= 50 pF; RL= 500 ohms. 3.9 Input pulse width. Delay lines shall be capable of passing a minimum input pulse width of 5
20、0 percent of total delay time. 3.10 DC characteristics. See table III. 3.11 Logic 1 fanout. Twenty per unit maximum (one tap capable of driving 20 TTL inputs). 3.12 Logic 0 fanout. Ten per tap maximum (one tap capable of driving 10 TTL inputs). 3.13 Thermal shock. In accordance with MIL-PRF-83532. 3
21、.14 Sealing. In accordance with MIL-PRF-83532. 3.15 Terminal strength. In accordance with MIL-PRF-83532. 3.16 Vibration. In accordance with MIL-PRF-83532. 3.17 Shock. In accordance with MIL-PRF-83532. 3.18 Immersion. In accordance with MIL-PRF-83532. 3.19 Moisture resistance. In accordance with MIL-
22、PRF-83532. 3.20 Solderability. In accordance with MIL-PRF-83532. 3.21 Resistance to solvents. In accordance with MIL-PRF-83532. 3.22 Operating temperature range. Operating temperature range shall be -55C to +125C. 3.23 Recycled, recovered, or environmentally preferable materials. Recycled, recovered
23、, or environmentally preferable materials should be used to the maximum extent possible, provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.24 Manufacturer eligibility. To be eligible for listing as an
24、approved source of supply, a manufacturer shall be listed on the MIL-PRF-83532 Qualified Product List for at least one part, or perform the group A and group B inspections specified herein on a sample of parts agreed upon by the manufacturer and DSCC-VA. Provided by IHSNot for ResaleNo reproduction
25、or networking permitted without license from IHS-,-,-CODE IDENT NO. 14933 DWG NO. 85014 DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A REV G SHEET 5 3.25 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be an approved source of supply.
26、3.26 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and externally. Tin content of resistor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.4). 3.27 Marking. Delay lines s
27、hall be marked with the complete DESC drawing PIN (see 1.2), the DESC CAGE code (14933), and the manufacturers CAGE code as a minimum. The “JAN“ or “J“ marking shall not be used. 3.28 Workmanship. The delay line shall be uniform in quality and free from any defects that will affect life, serviceabil
28、ity, or appearance in accordance with MIL-PRF-83532. TABLE I. Dash numbers and delay characteristics at 25C, VCC= 5.00 .01 volts. 1/ Dash number Tap 1 pin 13 Tap 2 pin 3 Tap 3 pin 12 Tap 4 pin 4 Tap 5 pin 11 Tap 6 pin 5 Tap 7 pin 10 Tap 8 pin 6 Tap 9 pin 9 Tap 10 pin 8 01 02 03 6 2 ns 6 2 ns 6 2 ns
29、1 2 ns 2 2 ns 2.5 2 ns 2 2 ns 4 2 ns 5 2 ns 3 2 ns 6 2 ns 7.5 2 ns 4 2 ns 8 2 ns 10 2 ns 5 2 ns 10 2 ns 12.5 2 ns 6 2 ns 12 2 ns 15 2 ns 7 2ns 14 2 ns 17.5 2 ns 8 2 ns 16 2 ns 20 2 ns 9 2 ns 18 2 ns 22.5 2 ns 04 05 06 5 2 ns 10 2 ns 15 2 ns 10 2 ns 20 2 ns 30 2 ns 15 2 ns 30 2 ns 45 5% 20 2 ns 40 2
30、ns 60 5% 25 2 ns 50 5% 75 5% 30 2 ns 60 5% 90 5% 35 2 ns 70 5% 105 5% 40 2 ns 80 5% 120 5% 45 5% 90 5% 135 5% 50 5% 100 5% 150 5% 07 08 09 20 2 ns 25 2 ns 30 2 ns 40 2 ns 50 5% 60 5% 60 5% 75 5% 90 5% 80 5% 100 5% 120 5% 100 5% 125 5% 150 5% 120 5% 150 5% 180 5% 140 5% 175 5% 210 5% 160 5% 200 5% 24
31、0 5% 180 5% 225 5% 270 5% 200 5% 250 5% 300 5% 10 11 12 40 2 ns 50 5% 60 5% 80 5% 100 5% 120 5% 120 5% 150 5% 180 5% 160 5% 200 5% 240 5% 200 5% 250 5% 300 5% 240 5% 300 5% 360 5% 280 5% 350 5% 420 5% 320 5% 400 5% 480 5% 360 5% 450 5% 540 5% 400 5% 500 5% 600 5% 13 70 5% 140 5% 210 5% 280 5% 350 5%
32、 420 5% 490 5% 560 5% 630 5% 700 5% 1/ Delays at taps 2 through 10 are referenced to tap 1 for dash numbers 01, 02, and 03. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-CODE IDENT NO. 14933 DWG NO. 85014 DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, O
33、HIO SIZE A REV G SHEET 6 TABLE II. Dash numbers and delay characteristics at -55C, and +125C, VCC= 5.00 .01 volts. 1/ Dash number Tap 1 pin 13 Tap 2 pin 3 Tap 3 pin 12 Tap 4 pin 4 Tap 5 pin 11 Tap 6 pin 5 Tap 7 pin 10 Tap 8 pin 6 Tap 9 pin 9 Tap 10 pin 8 01 02 03 6 3 ns 6 3 ns 6 3 ns 1 3 ns 2 3 ns 2
34、.5 3 ns 2 3 ns 4 3 ns 5 3 ns 3 3 ns 6 3 ns 7.5 3 ns 4 3 ns 8 3 ns 10 3 ns 5 3 ns 10 3 ns 12.5 3 ns 6 3 ns 12 3 ns 15 3 ns 7 3 ns 14 3 ns 17.5 3 ns 8 3 ns 16 3 ns 20 3 ns 9 3 ns 18 3 ns 22.5 3 ns 04 05 06 5 3 ns 10 3 ns 15 3 ns 10 3 ns 20 3 ns 30 3 ns 15 3 ns 30 3 ns 45 8% 20 3 ns 40 8% 60 8% 25 3 ns
35、 50 8% 75 8% 30 3 ns 60 8% 90 8% 35 3ns 70 8% 105 8% 40 8% 80 8% 120 8% 45 8% 90 8% 135 8% 50 8% 100 8% 150 8% 07 08 09 20 3 ns 25 3 ns 30 3 ns 40 8% 50 8% 60 8% 60 8% 75 8% 90 8% 80 8% 100 8% 120 8% 100 8% 125 8% 150 8% 120 8% 150 8% 180 8% 140 8% 175 8% 210 8% 160 8% 200 8% 240 8% 180 8% 225 8% 27
36、0 8% 200 8% 250 8% 300 8% 10 11 12 40 8% 50 8% 60 8% 80 8% 100 8% 120 8% 120 8% 150 8% 180 8% 160 8% 200 8% 240 8% 200 8% 250 8% 300 8% 240 8% 300 8% 360 8% 280 8% 350 8% 420 8% 20 8% 400 8% 480 8% 360 8% 450 8% 540 8% 400 8% 500 8% 600 8% 13 70 8% 140 8% 210 8% 280 8% 350 8% 420 8% 490 8% 560 8% 63
37、0 8% 700 8% 1/ Delays at taps 2 through 10 are referenced to tap 1 for dash numbers 01, 02, and 03. TABLE III. DC characteristics. Limits Test Symbol Conditions -55C TC +125C Min Max Unit High level output voltage VOHVCC= 4.5 V VIH= 2.0 V IOH= -1 mA 2.5 V Low level output voltage VOLVCC= 4.5 V VIL=
38、0.8 V IOL= 20 mA - 0.5 V Input clamp voltage VICVCC= 4.5 V II= -18 mA TC= +25C - -1.2 V IIH1VCC= 5.5 V VIH= 2.7 V - 100 A High level input current IIH2VCC= 5.5 V VIH= 5.5 V - 2,000 A Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-CODE IDENT NO. 1493
39、3 DWG NO. 85014 DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A REV G SHEET 7 TABLE III. DC characteristics - Continued Limits Test Symbol Conditions -55C TC +125C Min Max Unit Low level input current IILVCC= 5.5 V VIL= 0.5 V - -4.00 mA Short circuit output current IOSVCC= 5.5 V VOS= 0.0 V (No
40、t more than one output shorted at a time) -40 -150 mA Low level supply current ICCLVCC= 5.5 VI= 0.0 V - 130 mA 4. QUALITY ASSURANCE PROVISIONS 4.1 Conformance inspection. 4.1.1 Inspection of product for delivery. Inspection of product for delivery shall consist of option A or option C (see table IV)
41、 as stipulated by the acquiring activity. The tests listed shall be performed in the order shown and shall be in accordance with the group A inspection of MIL-PRF-83532. TABLE IV. Inspection of product for delivery. Option A Option C Subgroup I Thermal shock (15 cycles) Seal Delay time Rise time DC
42、characteristics Subgroup II Delay time at temperature extremes Dimensions Visual inspection Subgroup I Delay time Rise time DC characteristics Subgroup II Delay time at temperature extremes Dimensions Visual inspection Provided by IHSNot for ResaleNo reproduction or networking permitted without lice
43、nse from IHS-,-,-CODE IDENT NO. 14933 DWG NO. 85014 DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A REV G SHEET 8 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be perfo
44、rmed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within th
45、e military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES 6.1 Intended use. Delay lines conforming to this drawing are
46、intended for use when military specifications do not exist and when devices that will perform the required function are not available for OEM application. Items conforming to this drawing will replace similar items manufactured in accordance with contractor-prepared specifications and drawings. 6.2
47、Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirement for delivery of one copy of the conformance inspection data or certificate of compliance that partve passed conformance inspection with each shipment of parts by the manufacturer. c. Requirement for the manufacturer to notify the contracting activity in the event of a change in product. d. Requirements for packaging and packing. 6.3 Supersession data. Effective with revision E of this drawing, a suffix
