欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    DLA A-A-59461-2000 GRINDING AND SANDING MACHINE PLATEN ABRASIVE BELT WET AND DRY [Superseded DLA MIL-G-80176 B CANC NOTICE 2 DLA MIL-G-80176 B VALID NOTICE 1 DLA MIL-G-80176 B (1) .pdf

    • 资源ID:687432       资源大小:257.65KB        全文页数:6页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    DLA A-A-59461-2000 GRINDING AND SANDING MACHINE PLATEN ABRASIVE BELT WET AND DRY [Superseded DLA MIL-G-80176 B CANC NOTICE 2 DLA MIL-G-80176 B VALID NOTICE 1 DLA MIL-G-80176 B (1) .pdf

    1、INCH-POUND A-A-5946 1 11 February 2000 SUPERSEDING 15 November 1982 MIL-G-80176B COMMERCIAL ITEM DESCRIPTION GRINDING AND SANDING MACHINE, PLATEN, ABRASIVE BELT, WET AND DRY The General Services Administration has authorized the use of this commercial item description as a replacement for MIL-G-80 1

    2、76B for all federal agencies. 1. SCOPE. This comercial item description (CID) covers wet and dry abrasive belt platen grinding and sanding machines and accessories intended for use in secondary finishing operations such as flat grinding, deburring, chamfering, rounding of edges, and fieehand grindin

    3、g. 2. CLASSIFICATION. The abrasive belt platen grinding and sanding machines shall be of the following types, classes, and sizes. The type, class, and size to be furnished shall be as specified (see 7.2(b). Type1 -Dry Type II - Wet Class A - Vertical platen Class B - Horizontal platen Class C - Comb

    4、ination vertical or horizontal platen Class D - Combination adjustable vertical to horizontal platen Size - Sizes are shown in table I Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any other data which may improve this document should be sent to: Defense Supply

    5、 Center Richmond (DSCR), ATTN: DSCR-VBD, 8000 Jefferson Davis Highway, Richmond, VA 23297-561 O. AMSC N/A FSC 3419 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Licensed by Information Handling Services9038054 UU05638 648 aSi -_i Size 1 2 3 A-A-59461 inches 1 (typ

    6、e I only) 2 3 TABLE I. Sizes of grinding and sanding machines. Belt width, 4 6 8 10 12 14 4 6 8 10 12 14 3. SALIENT CHARACTERISTICS 3.1 General reauirements. The grinding or sanding machine shall be new and one of the manufacturers current models capable of operation in accordance with the requireme

    7、nts herein. All parts subject to wear, breakage, or distortion shall be accessible for adjustment, replacement, and repair. 3.2 Components. The abrasive belt grinding or sanding machine shall include, as a minimum, the following components. 3.2.1 M. The base shall support the other elements of the m

    8、achine and shall incorporate materials, shape, and mass to minimize adverse vibration and deflection. The base shall provide a means for leveling and anchoring the mache. 3.2.2 Frame. The fiame shall have provisions for mounting the hood and side guards, platen, , abrasive belt drive system, abrasiv

    9、e belt, and workpiece support. 3.2.3 Hood and side guards. Unless otherwise specified (see 7.2(c), the machine shall have a hood and side guards to minimize the discharge of abrasive dust, abraded metal, and water spray toward the operator. 3.2.4 Platen. Unless otherwise specified (see 7.2(d), the p

    10、laten shall provide a work area length that will be a minimum of one and one-half times the width of the belt. Unless otherwise specified (see 7.2(e), the platen shall be constructed of the material considered by the manufacturer as standard. 3.2.5 Workpiece support. Unless otherwise specified (see

    11、7.2(f), the grinding machine shall have a worktable or other workpiece support constructed of the material considered by the manufacturer as standard. 2 Licensed by Information Handling ServicesA-A-5946 1 3.2.6 Abrasive belt system. The abrasive belt system shall consist of abrasive belt contact whe

    12、els and an electric motor with either a direct drive coupling or a belt drive system. The abrasive belt system shall have means for adjusting the tension and tracking alignment of the abrasive belt. When a motor belt drive system is utilized, a means for adjusting the tension of the drive belts shal

    13、l be provided. 3.2.7 Abrasive belt. If required, the grinding machine shall be furnished with abrasive belts of the quantity, grit type, and grit size.as specified (see 7.2(g). Belt sizes shall be in accordance with International Organization for Standardization (ISO) 1929, “Abrasive belts - Dimensi

    14、ons, To lerances and Designation“. 3.2.8 Manual controls. Unless otherwise specified (see 7.2(h), the machine shall be provided with the manufactures standard machine controls. 3.2.9 Coolant system. Type II grinding or sanding machines shall have a coolant system. Unless otherwise specified (see 7.2

    15、(i), the coolant system shall consist of a reservoir, pump, strainer, and all necessary piping. 3.2.10 Electrical system. Unless otherwise specified (see 7.26), the electrical system shall conform to the American National Standards Instituternational Fire Prevention Association (ANSINFPA) 79, “Elect

    16、rical Standard for Industrial Machinery“. Motors less than one horsepower shall have 1 15-v01t, 1 -phase, 60-hertz circuit capability. Motors one horsepower or greater shall have dual 230/46O-volty 3-phaseY 60-hertz circuit capability and shall be wired for the voltage specified (see 7.2(k). 3.2.1 1

    17、 Electric motors. The belt grinding machine drive motor(s) shall have sealed and permanently lubricated ball or roller bearings, shall be energy efficient, and shall conform to the National Electrical Manufacturers Association (NEMA) MG- 1 , “Motors and Generators“. Unless otherwise specified (see 7

    18、.2(1), the motors shall be totally enclosed and fan cooled (TEFC). 3.2.12 Optional accessories. Optional accessories shall be provided as specified (see 7.2(m). 3.3 Performance. Unless otherwise specified (see 7.2(n), the belt grinding or sanding machine shall be operated at no load for not less tha

    19、n 30 minutes. Proper operation of all controls, motors, and adjusting mechanisms shall be verified during the trial period. 3.4 Machine dimensions and weight. If required, the maximum machine dimensions (length, width, and height) and machine weight shall not exceed the restrictions specified (see 7

    20、.2(0). 3.5 Safetv and health reauirements. The manufacturer shall ensure that the machine and all equipment and accessories used on the machine shall be in compliance with Occupational Safety and Health Administration (OSHA) 29 CFR PART 1910,“Occupational Safety and Health Standards for General Indu

    21、stry“. 3 Licensed by Information Handling Services9038054 0005b40 2Tb - -_I _- A-A-59461 a. b. d. e. f. g. h. C. 1. 3.6 Nameplate. A nameplate shall be securely attached to the machine. Unless otherwise specified (see 7.2(p), the nameplate shall contain the following information: Nomenclature Manufa

    22、cturers name Serial number Machine model designation Power input (volts, total amperes, phase, -frequency) Short-circuit/over-current rating Contract number or order number National stock number Date of manufacture 3.7 Lubrication plate or chart. When specified (see 7.2(q), a lubrication plate or ch

    23、art shall be attached to the machine. The information provided on the plate or chart shall include: a. Points of lubricant application b. Servicing interval c. Type of lubricant(s) with Society of Automotive Engineers (SAE) number or lubricant identifier 4. REGULATORY REQUIREMENTS 4.1 Recovered mate

    24、rials. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 4.2 Environmental protection. The item shall meet all applicable Environmental Protection Agency (EPA) restrictio

    25、ns in effect on the date of the contract. These regulations apply to the emission of materials hazardous to the environment or the users health and shall be adhered to during the manufacturing, service, transportation, storage, and operatioduse of the item. 5. QUALITY ASSURANCE PROVISIONS 5.1 Produc

    26、t conformance. The products shall meet the salient characteristics of this commercial item description; conform to the manufacturers own drawings, specifications, standards, and quality assurance practices; and be the same product offered for sale in the commercial market. The Government reserves th

    27、e right to require proof of such conformance. 5.2 Warranty. Unless otherwise specified (see 7.2(r), the manufacturers standard commercial warranty, tem, and conditions shall apply. 6. PACKAGING 6.1 Preservation, pack, and marking. For acquisition purposes, the machine shall be preserved, packed, and

    28、 marked as specified in the acquisition order (see 7.2(s). 4 Licensed by Information Handling ServicesA-A-5946 1 7. NOTES 7.1 Sources of documents. 7.1.1 m. The FAR may be obtained fiom the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402-000 1. 7.1.2 ANSI standards

    29、. Copies of IS0 standards may be obtained fiom the American National Standards Institute, 11 West 42nd Street, New York, NY 10036. 7.1.3 NEMA standards. Copies of NEMA standards may be obtained Tom the National Electrical Manufacturers Association, 1300 North 17th Street, Suite 1847, Rosslyn, VA 222

    30、09. 7.1.4 NFPA standards. Copies of NFPA standards may be obtained fiom the National Fire Protection Association, 1 Batterymarch Park, Quincy, MA 02269-9 1 01. 7.1.5 OSHA standards. Copies of OSHA standards may be obtained from the U.S. Department of Labor, 200 Constitution Avenue NW, Room 423, Wash

    31、ington, DC 2021 O. 7.2 Ordering data. Acquisition documents must speci the following: a. b. d. e. f. 5 h. C. 1. J- k. 1. m. n. O. P. 4. r. S. Title, number, and date of this document Type, class, and size of grinding and sanding machine required (see 2) Hood and side guards, if different (see 3.2.3)

    32、 Platen size, if different (see 3.2.4) Platen material, if different (see 3.2.4) Workpiece support, if different (see 3.2.5) Abrasive belts, as specified (see 3.2.7) Manual controls, if different (see 3.2.8) Coolant system, if different (see 3.2.9) Electrical system industrial standard, if different

    33、 (see 3.2.1 O) Electrical system voltage, as specified (see 3.2.1 O) Electric motors, if different (see 3.2.1 i) Optional accessories, as specified (see 3.2.12) Performance, if different (see 3.3) Machine dimensions and weight, as specified (see 3.4) Nameplate, if different (see 3.7) Lubrication pla

    34、te, if required (see 3.8) Warranty, if different (see 5.2) Packaging requirements, if different (see 6.1) 5 Licensed by Information Handling Services7.3 Part identification number (PIN). The following part identification numbering procedure is for government purposes and does not constitute a requir

    35、ement for the contractor. AA59461 - X X XX Size: Class: A - Vertical platen See table I for sizes B - Horizontal platen C - Combination vertical or horizontal platen D - Combination adjustable vertical to horizontal platen Type: 1 - Type1 -Dry 2 - Type II - Wet CID number k- MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: Custodians: GSA - 6FET Army - AL Navy - SH Air Force - 99 Reviewers: Navy - AS, MC, OS Air Force - 84 Preparing activity: DLA - GS (Project 341 9-0232) 6 Licensed by Information Handling Services


    注意事项

    本文(DLA A-A-59461-2000 GRINDING AND SANDING MACHINE PLATEN ABRASIVE BELT WET AND DRY [Superseded DLA MIL-G-80176 B CANC NOTICE 2 DLA MIL-G-80176 B VALID NOTICE 1 DLA MIL-G-80176 B (1) .pdf)为本站会员(lawfemale396)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开