欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    DLA A-A-55760 A-2011 RUBBER SILICONE STRIP SHAPE 16.pdf

    • 资源ID:687045       资源大小:33.41KB        全文页数:4页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    DLA A-A-55760 A-2011 RUBBER SILICONE STRIP SHAPE 16.pdf

    1、AMSC N/A FSC 9320 A-A-55760A 5 May 2011 SUPERSEDING A-A-55760 13 September 1995 COMMERCIAL ITEM DESCRIPTION RUBBER, SILICONE; STRIP, SHAPE 16 The General Services Administration has authorized the use of this Commercial Item Description for all Federal Agencies. 1. SCOPE. This commercial item descri

    2、ption (CID) covers a silicone rubber strip with shape 16 per figure 1. 2. CLASSIFICATION. The silicone rubber will be of the following classes and grades as specified. The designated grade number corresponds to the nominal Shore Durometer A hardness value. Class 1A Low temperature resistant Grade 40

    3、, 50, 60, 70, and 80 Class 1B Low temperature resistant and low compression set at high temperature Grade 40, 50, 60, 70, and 80 Class 2A High temperature resistant Grade 25, 40, 50, 60, 70, and 80 Class 2B High temperature resistant and low compression set Grade 25, 40, 50, 60, 70, and 80 Class 3A

    4、Low temperature, tear and flex resistant Grade 30, 50, and 60 Class 3B Tear and flex resistant Grade 30, 50, 60, 70, and 80 INCH-POUND Comments, suggestions, or questions on this document should be addressed to Defense Supply Center Philadelphia (DSCP), ATTN: DSCP-NASA, 700 Robbins Avenue, Philadelp

    5、hia, PA 19111-5096 or e-mail to dscpg&inspecommentsdla.mil . Since contact information can change, you may want to verify the currency of this address information using ASSIST Online database at https:/assist.daps.dla.mil .Provided by IHSNot for ResaleNo reproduction or networking permitted without

    6、license from IHS-,-,-A-A-55760A 2 3. SALIENT CHARACTERISTICS. 3.1 Dimensional and physical requirements. Dimensional and physical requirements shall conform to figure 1. Dimensional tolerance shall conform to the applicable commercial tolerance specified in CID A-A-59588. 1.000.060 48.00Figure 1 Dim

    7、ensional and Physical Requirements. Notes: 1. Dimensions are in inches. 2. Strengthening feature: Backing. 3. External strengthening feature location: One side. 4. Strengthening feature material: Polytetrafluoroethylene. 5. Fabrication method: Solid. 6. Surface condition: Smooth. 3.2 Material. Mater

    8、ial shall be silicone rubber formulated and processed to meet the physical and mechanical properties per the specified class and grade, when tested in accordance with ASTM test methods specified in Table I of CID A-A-59588. 3.3 Color. Unless otherwise specified, the color of the silicone rubber shal

    9、l be the natural color of the compound furnished. 3.4 Workmanship. The end product shall be clean, smooth finished, and free from dirt, flash or rough edges. 3.5 Marking. Unless otherwise specified (see ordering data), sheet material and strips (cut from sheet) shall be marked with the following inf

    10、ormation: Basic CID number, class, grade, designations, and the suppliers designations. The class and grade designations separated by a dash, shall be enclosed within parentheses. The markings shall be legible and placed in rows of constantly 5 inches apart. The suppliers designation (compound numbe

    11、r) shall appear immediately below the constantly recurring description symbols. The symbols shall be legible and shall be not less than 3/8 inches high. The symbols shall be applied by suitable means, using a black colored marking fluid to mark white colored silicones and a white colored marking flu

    12、id to mark other than white colored silicones. The marking shall not be obliterated by normal handling or by the action of petroleum-based oils. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55760A 3 3.6 Metric products. Products manufactured t

    13、o metric dimensions will be considered on an equal basis with those manufactured using inch-pound units, provided they fall within specified tolerances using conversion tables contained in the latest revision of ASTM SI 10, and all other requirements of this commercial item description are met. If a

    14、 product is manufactured to metric dimensions and those dimensions exceed the tolerances specified in the inch-pound units, a request should be made to the contracting officer to determine if the product is acceptable. 4. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged to use recovered

    15、 materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 5. PRODUCT CONFORMANCE. 5.1 Product conformance. The products provided shall meet the salient characteristics of this commercial item description, conform to the producers o

    16、wn drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial market. The government reserves the right to require proof of such conformance. 6. PACKAGING. Preservation, packing, and marking shall be as specified in the contract o

    17、r order. 7. NOTES. 7.1 Part identification number (PIN): the following part identification numbering procedure is for government purposes and does not constitute a requirement for the contractor. The PINs to be used for items acquired to this description are created as follows: AA55760 001 C 5 Grade

    18、 2 =25Clas 330 A =1A 4 =4BB 550 C =2A 6 =6DB 770 E =3A 8 =8FB N =NADimensions per Figure 1 Basic CID number 7.2 Ordering data. The contract or order should specify the following: a. Title, number, and date of this CID. b. Class and grade required. c. Marking if different (see 3.5). d. Color required

    19、 if other than natural color of compound furnished. e. Packaging requirements. 7.3 Source of documents. 7.3.1 ASTM SI10 is available from the ASTM International, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959 or online at http:/www.astm.org . Provided by IHSNot for ResaleNo reproduction or

    20、networking permitted without license from IHS-,-,-A-A-55760A 4 7.3.2 FAR. The Federal Acquisition Regulation is available from the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402 or online at http:/www.arnet.gov/far . 7.3.3 Government documents. Federal and militar

    21、y documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094. 7.4 Utilization caution. Use of this material in items that may come in contact with human skin, food, or portabl

    22、e water is not recommended without prior approval of the appropriate medical service. 7.5 Key words. Class Flex resistant Grade Low compression 7.6 Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent o

    23、f the changes. Military interests: Custodians: Preparing activty: Army MR DLA - IS Navy AS Air Force - 11 (Project 9320-2011-013) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-


    注意事项

    本文(DLA A-A-55760 A-2011 RUBBER SILICONE STRIP SHAPE 16.pdf)为本站会员(explodesoak291)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开