1、AMSC N/A FSC 4030 INCH-POUND A-A-55603A 10 October 2012 SUPERSEDING A-A-55603 2 May 1995 COMMERCIAL ITEM DESCRIPTION CLAMP, GUY (POLE LINE) The General Services Administration has authorized the use of this commercial item description for all federal agencies. 1. SCOPE. This commercial item descript
2、ion (CID) covers the general requirements for clamp, guy, (pole line). clamp, guy, (pole line) covered by this CID are intended for commercial/industrial applications. 2.CLASSIFICATION/PART OR IDENTIFICATION NUMBER (PIN). This CID uses a classification system which is included in the PIN as shown in
3、 the following example (see 7.1). AA55603 - 001 CID number Dash number 2.1 Dash numbers. See table I for all dash numbers and their associated dimensional information. 3. SALIENT CHARACTERISTICS. 3.1 Interface and physical dimensions. Clamp, guy, (pole line) supplied to this CID shall be as specifie
4、d herein (see figure 1) and dimensions in table I. 3.2 Material. The material shall be carbon steel in accordance with ASTM A29/A29M. 3.3 Finish. The finish shall be (hot dipped) in accordance with ASTM A153/A153M. 3.4 Screw threads. All screw threads shall be UNC-2 as specified in FED-STD-H28. 3.5
5、Galvanized. All screw threads shall not be galvanized. Comments, suggestions, or questions on this document should be addressed to DLA Land and Maritime, Attn: VAI, 3990 East Broad Street, Columbus, OH 43218-3990 or fluidflow.dla.mil. Since contact information can change, you may want to verify the
6、currency of this address information using the ASSIST Online at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55603A 2 3.6 Marking Clamp, guy (pole line) supplied to this CID shall be marked with the manufacturers (MFRs)
7、standard commercial PIN. (NOTE: The part number marked on the unit pack shall be the CID PIN.) 3.7 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets
8、 or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.8 Workmanship. Clamp, guy (pole line) shall be processed in such a manner as to be uniform in quality and shall be free from other defects that will affect life, serviceability, or ap
9、pearance. 4. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with 23.403 of the Federal Acquisition Regulation (FAR). 5. PRODUCT CONFORMANCE PROVISIONS. 5.1 Product conformance. The products provided shall meet
10、 the salient characteristics of this CID, conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial market. The Government reserves the right to require proof of such conformance. 6. PACKAGING. Preser
11、vation, packing, and marking shall be as specified in the contract or order. 7. NOTES. 7.1 PIN. The PIN should be used for Government purposes to buy commercial products to this CID. See section 2 for PIN format example. 7.2 Environmentally preferable material. Environmentally preferable materials s
12、hould be used to the maximum extent possible to meet the requirements of this specification. As of the dating of this document, the U.S. Environmental Protection Agency (EPA) is focusing efforts on reducing 31 priority chemicals. The list of chemicals and additional information is available on their
13、 website http:/www.epa.gov/osw/hazard/wastemin/priority.htm. Included in the EPA list of 31 priority chemicals are cadmium, lead, and mercury. Use of these materials should be minimized or eliminated unless needed to meet the requirements specified herein (see Section 3). 7.3 Commercial and Governme
14、nt Entity (CAGE) code. For ordering purposes, inventory control, and submission of these clamp, guy (pole line) to DLA Land and Maritime under the Military Parts Control Advisory Group (MPCAG) evaluation program, CAGE code 58536 should be used. 7.4 Source of documents. FEDERAL STANDARD FEDSTDH28 Scr
15、ew Thread Standards for Federal Services (Copies of these documents are available online at https:/assist.dla.mil/quicksearch / or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094). Provided by IHSNot for ResaleNo reproduction or networking p
16、ermitted without license from IHS-,-,-A-A-55603A 3 FEDERAL REGULATIONS FAR Federal Acquisition Regulations (FAR) (Copies of these documents are available online at www.acquisition.gov/comp/far/index.html or from the U.S. Government Printing Office, 732 North Capital Street, NW, Washington D.C. 20401
17、.) ASTM INTERNATIONAL ASTM A29/A29M - Standard Specification for Steel Bars, Carbon and Alloy, Hot-Wrought, General Requirements for ASTM A153/A153M - Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware (Copies of these documents are available online at http:/www.astm.org or
18、 from the ASTM International, P.O. Box C700, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.) 7.5 Ordering data. The contract or order should specify the following: a. CID document number, revision, and CID PIN. b. Product conformance provisions. c. Packaging requirements. 7.6 Commercial pr
19、oducts. As part of the market analysis and research effort, this CID was coordinated with the following manufacturers of commercial products. At the time of CID preparation and coordination, these manufacturers were known to have commercial products that would meet the requirements of this CID. (NOT
20、E: This information should not be considered as a list of approved manufacturers or be used to restrict acquisition to only the manufacturers shown.) MFRs CAGE MFRs name and address 08TX0 FOSS-BROWN INC 3411 SILVERSIDE RD STE 100WB WILMINGTON, DE 19810-4890 Tel: (941) 358-7400 Fax: (941) 358-7588 3
21、DPE3 JSO/MD INC 1961 SAINT ANDREWS DR RED OAK, TX 75154-5837 Tel: (972) 617-0677 Fax: (972) 576-8920 9N473 DIAL SUPPLY & MFG INC 1315 FM 1187 106 MANSFIELD, TX 76063-6194 Tel: (817) 453-3711 Fax: (817) 453-3716 Provided by IHSNot for ResaleNo reproduction or networking permitted without license fr
22、om IHS-,-,-A-A-55603A 4 7.7 Government users. To acquire information on obtaining these clamp, guy, (pole line) from the Government inventory system, contact DLA Land and Maritime, ATTN: DLA Land and Maritime Call Center (NAB), P.O. Box 3990, Columbus, OH 432183990 or telephone (614) 692-2271 or (61
23、4) 692-3191. 7.8 Legacy. This commercial item description is a replacement for MS16791 for all federal agencies (MS16791 is canceled as of 02-MAY-1995 and copies of these documents are available online at www.acquisition.gov/comp/far/index.html or from the U.S. Government Printing Office, 732 North
24、Capital Street, NW, Washington D.C. 20401.) 7.9 Clamp, guy (pole line) drawing with dimensions. See figure 1. FIGURE 1. Clamp, guy (pole line). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55603A 5 TABLE I. Dash numbers and dimensions 7.10 Cro
25、ss-reference. See table II. TABLE II. Cross reference table. Cancelled MS Pin Replacement CID PIN MS16791 - 1/ AA55603 - 1/ 1/ Represents the same designation codes for both MS and CID pins. 7.11 Changes from previous issue. The margins of this specification are marked with vertical lines to indicat
26、e where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespect
27、ive of the marginal notations and relationship to the last previous issue. CONCLUDING MATERIALS MILITARY INTERESTS: CIVIL AGENCY COORDINATION ACTIVITY: Custodians: GSA-FSA Army CR Navy YD Air Force 99 DLA-CC Reviewer activities: Preparing Activity: Army AR,CR4 DLA-CC Navy MC, SA Air Force 71 Project
28、 4030-2012-009 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Dash No. No. Bolt
29、s A B .125 C Max E Strand Size Bolt Size L Max -1 -2 -3 -4 -5 -6 2 3 3 3 3 4 1.563 1.563 1.563 1.656 2.125 1.656 1.625 1.625 1.625 1.750 1.750 1.750 .2812 .2812 .2812 .750 .750 .750 1.250 2.031 .938 2.031 2.031 1.953 .250 to .438 .250 to .438 .250 to .438 .313 to .500 .375 to .625 .313 to .500 .500-13 .500-13 .500-13 .625-11 .625-11 .625-11 3.375 6.188 4 6.188 6.188 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
