1、 Beneficial comments, recommendations, additions, deletions, clarifications, etc., and any data that may improve this document should be sent to: DLA Land and Maritime, ATTN: DLA Land and Maritime-VAT, P.O. Box 3990, Columbus, OH 43218-3990, or email mailto:CircuitProtectdscc.dla.mil. Since contact
2、information can change you may want to verify the currency of the address information using the ASSIST Online database at https:/assist.daps.dla.mil. AMSC N/A FSC 5920 INCH-POUND A-A-55494D 17 February 2011 SUPERSEDING A-A-55494C 6 July 2006 COMMERCIAL ITEM DESCRIPTION FUSE CARTRIDGE, SEMICONDUCTOR
3、TYPE, 250 VOLTS The General Services Administration has authorized the use of this commercial item description for all federal agencies. 1. SCOPE. This commercial item description (CID) covers the general requirements for 250 volt semiconductor type fuse cartridges. Fuse cartridges covered by this C
4、ID are intended for commercial/industrial applications. 2. CLASSIFICATION/PART OR IDENTIFICATION NUMBER (PIN). This CID uses a classification system which is included in the PIN as shown in the following example (see 7.1). AA55494 - 001 CID PIN Dash number (see table I) 3. SALIENT CHARACTERISTICS. 3
5、.1 Interface and physical dimensions. Fuse cartridges supplied to this CID shall be as specified herein (see figure 1 and figure 2). 3.2. Ampere rating. The ampere rating shall be as specified in table I. 3.3 Voltage rating. The voltage rating shall be 250 V ac maximum. 3.4 Short circuit interrupt r
6、ating. The short circuit interrupt shall be 200,000 amperes root mean square (RMS) symmetrical. 3.5 Maximum current clearing I2t. The maximum current clearing I2t shall be as specified in table I. 3.6 Marking. Fuse cartridges supplied to this CID shall be marked with the manufacturers (MFRs) standar
7、d commercial PIN. (NOTE: The part number marked on the unit pack shall be the CID PIN.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55494D 2 AA55494- Dimensions A B C 001 through 006 2.00 (50.80) .563 (14.30) (.505) 12.83 .432 (10.97) Configu
8、ration A NOTES: 1. Dimensions are in inches. 2. Unless otherwise specified, tolerance is .005 inch (0.13 mm). FIGURE 1. Configuration A and dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55494D 3 AA55494- Dimensions A B C D E F G H 0
9、07 through 011 1.631 (41.43) 1.557 (39.55) 2.261 (57.43) 2.600 (66.04) 2.495 (63.37) 3.188 (80.98) .813 (20.65) .755 (19.18) .621 (15.77) .343 (8.71) .180 (4.57) 012 through 017 1.631 (41.43) 1.589 (4.036) 2.333 (59.26) 2.184 (55.47) 2.437 (61.90) 3.126 (79.40) 1.219 (30.96) 1.000 (25.40) .750 (19.0
10、5) .349 (8.86) .307 (7.80) 1.88 (4.78) 018 through 023 1.594 (40.49) 2.41 (61.21) 2.247 (57.07) 2.942 (74.73) 2.900 (73.66) 3.843 (97.61) 1.500 (38.10) 1.000 (25.40) .406 (10.31) .251 (6.38) Configuration B NOTES: 1. Dimensions are in inches. 2. Unless otherwise specified, tolerance is .005 inch (0.
11、13 mm). FIGURE 2. Configuration B and dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55494D 4 TABLE I. Electrical characteristics. AA55494- Ampererating I2t (A2s) AA55494- Ampererating I2t (A2s) 001 5 100 013 80 3,000 002 10 200 014
12、100 5,000 003 15 250 015 125 7,500 004 20 300 016 150 12,000 005 25 350 017 200 20,000 006 30 390 018 250 38,000 007 35 460 019 300 55,000 008 40 560 020 350 73,000 009 45 720 021 400 100,000 010 50 880 022 500 190,000 011 60 1,300 023 600 260,000 012 70 2,200 3.7 Recycled, recovered, or environment
13、ally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.8 Workmanship. Fu
14、se cartridges shall be processed in such a manner as to be uniform in quality and shall be free from other defects that will affect life, serviceability, or appearance. 4. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in a
15、ccordance with 23.403 of the Federal Acquisition Regulation (FAR). 5. PRODUCT CONFORMANCE PROVISIONS 5.1 Product conformance. The products provided shall meet the salient characteristics of this CID, conform to the producers own drawings, specifications, standards, and quality assurance practices, a
16、nd be the same product offered for sale in the commercial market. The Government reserves the right to require proof of such conformance. 5.2 Market acceptance. The following market acceptance criteria are necessary to document the quality of the product to be provided under this CID: a. The company
17、 producing the item must have been producing a product meeting the requirements of this CID for at least 2 years. b. The company producing the item must have sold 1,000 units meeting this CID in the commercial marketplace over the past 2 years. 6. PACKAGING. Preservation, packing, and marking shall
18、be as specified in the contract or order. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55494D 5 7. NOTES. 7.1 PIN. The PIN should be used for Government purposes to buy commercial products to this CID. See the classification section for PIN fo
19、rmat example. 7.2 Environmentally preferable material. Environmentally preferable materials should be used to the maximum extent possible to meet the requirements of this specification. As of the dating of this document, the U.S. Environmentally Protection Agency (EPA) is focusing efforts on reducin
20、g 31 priority chemicals. The list of chemicals is available on their website at http:/www.epa.gov/osw/hazard/wastemin/priority.htm. Use of these materials on the list should be minimized or eliminated unless needed to meet the requirements specified herein (see Section 3). 7.3 Commercial and Governm
21、ent Entity (CAGE) code. For ordering purposes, inventory control, and submission of these fuse cartridges to DLA Land and Maritime under the Military Parts control Advisory Group (MPCAG) evaluation program, CAGE code 58536 should be used. 7.4 Source of documents. FEDERAL REGULATIONS FAR - Federal Ac
22、quisition Regulations (FAR). (Copies of this document are available online at https:/www.acquisition.gov/comp/far/index.html or from the U.S. Government Printing Office, 732 North Capital Street, NW, Washington D.C. 20401-0001.) 7.5 Ordering data. The contract or order should specify the following:
23、a. CID document number, revision, and CID PIN. b. Product conformance provisions. c. Packaging requirements. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55494D 6 7.6 Commercial products. As part of the market analysis and research effort, thi
24、s CID was coordinated with the following manufacturers of commercial products. At the time of CID preparation and coordination, these manufacturers were known to have commercial products that would meet the requirements of this CID. (NOTE: This information should not be considered as a list of appro
25、ved manufacturers or be used to restrict procurement to only the manufacturers shown.) MFRs CAGE MFRs name and address 067U2 DENCO Fuses, Incorporated 8244 S.W. 103 Avenue Miami, FL 33173-3906 Phone number: (305) 273-6226 Facsimile number: (305) 273-4335 E-mail: mailto: Uniform Resource Locator (URL
26、): http:/ 71400 Cooper Bussmann, Incorporated P. O. Box 14460 St. Louis, MO 63178-4460 Phone number (636) 394-2877 Facsimile number (800) 544-2570 E-mail: mailto: URL: http:/ 71424 Ferraz Shawmut 374 Merrimac Street Newburyport, MA 01950-1930 Phone number: 978-462-6662 Facsimile number: 978-462-018
27、1 E-mail: mailto: URL: http:/ 75915 Littelfuse Incorporated 8755 W. Higgins Road Chicago, IL 60631-2708 Phone number (800) 999-9445 Facsimile number (847) 391-0753 E-mail: mailto: URL: http:/ Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55494D
28、 7 7.7 Part number (P/N) supersession data. These CID PINs supersede the following MFRs P/Ns as shown. This information is being provided to assist in reducing proliferation in the Government inventory system. TABLE III. P/N supersession data. CID dash number (see table I) AA55494- Vendor Commercial
29、 P/N 1/ CAGE 067U2 CAGE 71424 CAGE 71400 CAGE 75915 001 UFR25X005 A25X5-1 FWX 5A14F L25S5 002 UFR25X010 A25X10-1 FWX 10A14F L25S10 003 UFR25X015 A25X15-1 FWX 15A14F L25S15 004 UFR25X020 A25X20-1 FWX 20A14F L25S20 005 UFR25X025 A25X25-1 FWX 25A14F L25S25 006 UFR25X030 A25X30-1 FWX 30A14F L25S30 007 U
30、FR25X035 A25X35-4 FWX 35A L25S35 008 UFR25X040 A25X40-4 FWX 40A L25S40 009 UFR25X045 A25X45-4 FWX 45A L25S45 010 UFR25X050 A25X50-4 FWX 50A L25S50 011 UFR25X060 A25X60-4 FWX 60A L25S60 012 UFR25X070 A25X70-4 FWX 70A L25S70 013 UFR25X080 A25X80-4 FWX 80A L25S80 014 UFR25X100 A25X100-4 FWX 100A L25S10
31、0 015 UFR25X125 A25X125-4 FWX 125A L25S125 016 UFR25X150 A25X150-4 FWX 150A L25S150 017 UFR25X200 A25X200-4 FWX 200A L25S200 018 UFR25X250 A25X250-4 FWX 250A L25S250 019 UFR25X300 A25X300-4 FWX 300A L25S300 020 UFR25X350 A25X350-4 FWX 350A L25S350 021 UFR25X400 A25X400-4 FWX 400A L25S400 022 UFR25X5
32、00 A25X500-4 FWX 500A L25S500 023 UFR25X600 A25X600-4 FWX 600A L25S600 1/ The manufacturers P/N shall not be used for procurement to the requirements of this CID. At the time of preparation of this CID, the aforementioned commercial products were reviewed and could be replaced by the CID PIN shown.
33、For actual part marking requirements, see 3.6. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55494D 8 7.8 Government users. To acquire information on obtaining these fuse cartridges from the Government inventory system, contact DLA Land and Mar
34、itime, ATTN: DLA Land and Maritime-FMX, P.O. Box 3990, Columbus, OH 43218-3990, or telephone (614) 692-3677. 7.8.1 National stock number (NSN). The following is a list of NSNs assigned which correspond to this CID. The list is for information only and may not be indicative of all possible NSNs assoc
35、iated with the CID. For up to date information on assigned NSNs, please contact the aforementioned DSCC office (See 7.8). TABLE IV. NSNs. Dash number (see table I) AA55494- NSN Dash number (see table I) AA55494- NSN 001 5920-00-615-7624 013 N/A 002 N/A 014 5920-01-433-3378 003 5920-00-843-9007 015 N
36、/A 004 5920-00-617-9694 016 5920-00-775-7994 005 N/A 017 N/A 006 5920-00-778-7313 018 5920-00-615-7625 007 5920-01-354-6243 019 N/A 008 5920-01-195-7254 020 N/A 009 5920-01-327-6414 021 N/A 010 5920-00-890-8999 022 N/A 011 N/A 023 5920-00-768-4388 012 N/A 7.9 Changes from previous issue. Marginal no
37、tations are not used in this revision to identify changes with respect to the previous issue due to the extensiveness of the changes. MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: GSA - FAS Custodians: Navy - EC Preparing activity: DLA - CC DLA-CC Project 5920-2011-028 NOTE: The activities
38、 listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
