欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    DLA A-A-50493 C-2011 OIL PENETRATING (FOR LOOSENING FROZEN METALLIC PARTS).pdf

    • 资源ID:686244       资源大小:48.81KB        全文页数:7页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    DLA A-A-50493 C-2011 OIL PENETRATING (FOR LOOSENING FROZEN METALLIC PARTS).pdf

    1、Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data that may improve this document should be sent to: STDZNMGTdla.mil or Defense Logistics Agency Aviation VEB, 8000 Jefferson Davis Highway, Richmond, VA 23297-5610. Since contact information can change, you m

    2、ay want to verify the currency of this address information using the ASSIST database at https:/assist.daps.dla.mil. FSC 9150 INCH-POUND A-A-50493C SUPERSEDING 22 July 2011 A-A-50493B 30 August 2001 COMMERCIAL ITEM DESCRIPTION OIL, PENETRATING (FOR LOOSENING FROZEN METALLIC PARTS) The General Service

    3、s Administration has authorized the use of this commercial item description for all federal agencies. 1. SCOPE. This commercial item description (CID) establishes the government acquisition requirements for penetrating oil to be used for freeing of corroded and frozen metallic parts resisting moveme

    4、nt, without causing damage to such parts. The penetrating oil is applied to metal surfaces to break down rust and corrosion, reduce friction, and retard corrosion. 2. CLASSIFICATION. The penetrating oil shall be one of the following class and type combinations as specified (see 7.5(b). The unit of i

    5、ssue (see 7.5(c) and quantity required (see 7.5(d) shall be as specified in the acquisition order. 2.1 Class. Class A bio-based Class B non-bio-based 2.2 Type. Type I - liquid application (brush, dip, or spray) Type II - aerosol application Provided by IHSNot for ResaleNo reproduction or networking

    6、permitted without license from IHS-,-,-A-A-50493C 2 3. SALIENT CHARACTERISTICS 3.1 Materials. 3.1.1 Class A. The penetrating oil for class 1 shall be formulated with a bio-based oil, with or without additives. 3.1.2 Class B. The penetrating oil for class 2 shall be formulated with a synthetic oil or

    7、 light mineral oil, or a mixture of these oils, with or without additives. 3.2 Bio-based content. The class A penetrating oil shall have a minimum of 68% by weight of bio-based content in accordance with United States Department of Agriculture (USDA) designated categories of bio-based products in th

    8、e BioPreferred Program for penetrating lubricants when tested in accordance with ASTM International (ASTM) D6866, “Standard Test Methods for Determining the Biobased Content of Solid, Liquid, and Gaseous Samples Using Radiocarbon Analysis”. A bio-based material shall be defined in accordance with th

    9、e Farm Security and Rural Investment Act (also called FSRIA or the 2002 Farm Bill) of 2002 Section 9002 (Public Law 107-171, dated May 13, 2002) and determined by the US Secretary of Agriculture. 3.3 Performance. 3.3.1 Pour point. The penetrating oil shall have a pour point of not greater than -14 F

    10、 (-25 C) when tested in accordance with ASTM D97, “Standard Test Method for Pour Point of Petroleum Products“. 3.3.2 Viscosity. The penetrating oil shall have a viscosity of 1.7 to 10 millimeter2/second (mm2/s) at 104 F (40 C) when tested in accordance with ASTM D445, “Standard Test Methods for Kine

    11、matic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)“. 3.3.3 Flash point. Penetrating oil with a kinematic viscosity of 1.7 to 5.5 mm2/s at 104 F (40 C) shall have a minimum flash point of 125 F (51.7 C) when tested in accordance with ASTM D56, “Standard Test Meth

    12、od for Flash Point by Tag Closed Cup Tester“. Penetrating oil with a kinematic viscosity of greater than 5.5 mm2/s at 104 F (40 C) shall have a minimum flash point of 125 F (51.7 C) when tested in accordance with ASTM D93, “Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester“.

    13、3.3.4 Water. The penetrating oil shall have 0.0 percent water content when tested in accordance with ASTM D95, “Standard Test Method for Water in Petroleum Products and Bituminous Materials by Distillation“, and 40 Code of Federal Regulations (CFR) 60, Appendix A, Method 24, “Determination of Volati

    14、le Matter Content, Water Content, Density, Volume Solids, and Weight Solids of Surface Coatings“. 3.3.5 Corrosion. The penetrating oil shall cause no corrosion when tested in accordance with method 5306 “Corrosiveness of Emulsifiable Cutting Fluids” of FED-STD-791, “Lubricants, Provided by IHSNot fo

    15、r ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50493C 3 Liquid Fuels, and Related Products; Methods of Testing“. Isopropyl alcohol in accordance with ASTM D770, “Standard Specification for Isopropyl Alcohol“, and paragraph 4.4 of this document may be substituted for

    16、 the 1,1,1-Trichloroethane specified in the test method. The requirements for emulsification of samples and the subsequent addition of distilled water shall be eliminated when not applicable. 3.3.6 Surface tension. The penetrating oil shall have a surface tension of not greater than 44 milliNewtons/

    17、meter (mN/m) when tested in accordance with ASTM D3825, “Standard Test Method for Dynamic Surface Tension by the Fast-Bubble Technique“. 3.3.7 Interfacial tension. The penetrating oil shall have an interfacial tension of not greater than 33 mN/m when tested in accordance with ASTM D971, “Standard Te

    18、st Method for Interfacial Tension of Oil Against Water by the Ring Method“. 3.4 Workmanship. The penetrating oil shall be free from dirt, sediment, disagreeable odors, or other foreign matter as determined by visual or olfactory examination. 3.5 Propellant. For Type II material, the propellant shall

    19、 be carbon dioxide, nitrous oxide, or nitrogen. The propellant shall expel the contents of the container and shall be nonflammable in accordance with 49 CFR 173, “Shippers-General Requirements for Shipments and Packagings“. 4. REGULATORY REQUIREMENTS 4.1 Recovered materials. The offeror/contractor i

    20、s encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 4.2 Hazard communication standard. The contractor shall certify that no carcinogenic or potentially carcinogenic constituents are present in the

    21、 penetrating oil in accordance with 29 CFR 1910.1200, “Hazard Communication“ and 29 CFR 1910, Subpart Z, “Toxic and Hazardous Substances“. The contractor shall provide certification to this effect to the contracting officer or the contractors designated representative (see 7.5(e). 4.3 Toxicity. The

    22、materials used in the oil, unless specific material maximum levels are specified herein, shall have no known carcinogenic materials identified by Occupational Safety and Health Administration (OSHA) regulated carcinogens, as identified by 29 CFR 1990, “Identification, Classification, and Regulation

    23、of Carcinogens“, or International Agency for Research on Cancer (IARC) latest monographs, or the latest annual report of the National Toxicology Program (NTP), and shall have no extremely hazardous substances (EHS) or toxic chemicals identified in 40 CFR 355, Appendix A, “The List of Extremely Hazar

    24、dous Substances and Their Threshold Planning Quantities“ and 40 CFR 372, Subpart D, “Specific Toxic Chemical Listings“, respectively. The manufacturer shall not, unless specific material maximum levels are specified herein, allow the addition of any known or suspected carcinogens, extremely hazardou

    25、s substances, or toxic chemicals to the formulation. When any of these prohibited materials are or may be present, as a trace or as an impurity in another ingredient(s), the concentration of the prohibited material shall not equal or be Provided by IHSNot for ResaleNo reproduction or networking perm

    26、itted without license from IHS-,-,-A-A-50493C 4 greater than 0.1 percent by weight of the oil. The oil shall have no adverse effect on the health of personnel when used for its intended purpose. 4.4 Ozone-depleting chemicals. The materials used in the oil shall not contain class I or class II ozone

    27、depleting chemicals (ODC) as defined in 40 CFR 82, “Protection of Stratospheric Ozone“. In addition, no ODC shall be used in the manufacturing or testing of these products. 5. PRODUCT CONFORMANCE PROVISIONS 5.1 Product conformance. The products provided shall meet the salient characteristics of this

    28、 commercial item description, conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial marketplace. The government reserves the right to require proof of such conformance. 5.2 Market acceptability. T

    29、he following market acceptability criteria are necessary to document the quality of the product to be provided under this CID. a. The company must have produced penetrating oil meeting the salient characteristics of this CID for at least 3 years. b. The company must be able to show test data or lab

    30、results substantiating that the product offered meets the salient characteristics of this CID. c. The company must provide a warranty for the replacement of defective material. 6. PACKAGING 6.1 Preservation, packing, and marking. For acquisition purposes, the penetrating oil shall be preserved, pack

    31、ed, and marked as specified in the acquisition order (see 7.5(f). 7. NOTES 7.1 Part or identification number (PIN). The following part or identification numbering procedure is for government purposes and does not constitute a requirement for the contractor. Type: 1 - Type I (see 2.2) 2 - Type II AA5

    32、0493 X - X CID number Class: A Class A (see 2.1) B Class B Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50493C 5 7.2 Sources of documents. 7.2.1 Government documents. Copies of CFR FAR, and Public Law may be obtained from the Superintendent of

    33、 Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954. Electronic copies of CFR documents may be obtained from http:/www.access.gpo.gov/. Electronic copies of FAR documents may be obtained from http:/www.arnet.gov/far/. Electronic copies of the Public Law document may be obtained from http:/www.gpo

    34、.gov. 7.2.2 Federal standards. Copies of federal standards may be obtained from Standardization Documents Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094. Electronic copies of federal standards may be obtained from https:/assist.daps.dla.mil. 7.2.3 ASTM standards. Copies of

    35、ASTM standards are available online at http:/www.astm.org or from ASTM International, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959. 7.2.4 IARC monographs. International Agency for Research on Cancer (IARC) monographs may be obtained at http:/monographs.iarc.fr/ or from the World Health Or

    36、ganization (WHO) Publication Center, 49 Sheridan Avenue, Albany, NY 12210. 7.2.5 NTP reports. Copies of the latest Annual Report on Carcinogens, Summary, National Toxicity Program (NTP), is available at http:/ntp.niehs.nih.gov/or from the U.S. Department of Health and Human Services, National Instit

    37、ute of Environmental Health Services, Public Information Office, P.O. Box 12233, MD B2-04, Research Triangle Park, NC 27709. 7.3 Material safety data sheets. Contracting officers will identify those activities requiring copies of the completed material safety data sheets (MSDS) prepared in accordanc

    38、e with FED-STD-313. The pertinent government mailing addresses for submission of data are listed in FED-STD-313, and 29 CFR 1910.1200 requires that the MSDS for each hazardous chemical used in an operation must identify the activities requiring copies of the MSDS (see 7.5 (g). 7.4 National stock num

    39、bers (NSN). The NSNs listed in table I are assigned to the listed products. Other NSNs may also correspond with this document. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50493C 6 TABLE I. National stock numbers (NSNs) for bio-based and non-b

    40、io-based penetrating oils. Material NSN Type Container Size Class A Bio-based 9150-01-591-4213 I 1 pint can 9150-01-591-4247 I 1 gallon can 9150-01-591-4281 I 55 gallon drum 9150-01-591-4274 II 11 ounce aerosol Class B Non-bio-based 9150-00-261-7899 I 1 pint can 9150-00-262-8990 I 1 quart can 9150-0

    41、0-223-4119 I 1 gallon can 9150-00-852-4659 I 55 gallon drum 9150-00-529-7518 II 16 ounce aerosol 7.5 Ordering data. The contract or order should specify the following: a. CID document number, revision, and CID PIN b. Class and type (see 2) c. Unit of issue (see 2) d. Quantity (see 2) e. Certificatio

    42、n clause (see 4.2) f. Preservation, packing, and marking requirements (see 6.1) g. Hazardous material identification and material safety data sheets (see 7.3) 7.6 Subject term (key word) listing. bio-based bio-based content corrosion friction mineral rust synthetic Provided by IHSNot for ResaleNo re

    43、production or networking permitted without license from IHS-,-,-A-A-50493C 7 MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: Custodians: Army AT Navy SH Air Force 68 DLA GS GSA - FSA Preparing activity: DLA - GS3 (Project 9150-2011-008) NOTE: The activities listed above were interested in th

    44、is document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIT database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-


    注意事项

    本文(DLA A-A-50493 C-2011 OIL PENETRATING (FOR LOOSENING FROZEN METALLIC PARTS).pdf)为本站会员(吴艺期)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开