1、February 2015 Translation by DIN-Sprachendienst.English price group 8No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).IC
2、S 25.100.01; 25.060.20!%?cP“2286445www.din.deDDIN ISO 5610-10Tool holders with rectangular shank for indexable inserts Part 10: Style N (ISO 5610-10:2014),English translation of DIN ISO 5610-10:2015-02Klemmhalter mit Vierkantschaft fr Wendeschneidplatten Teil 10: Form N (ISO 5610-10:2014),Englische
3、bersetzung von DIN ISO 5610-10:2015-02Porte-plaquette queue rectangulaire pour plaquettes amovibles Partie 10: Forme N (ISO 5610-10:2014),Traduction anglaise de DIN ISO 5610-10:2015-02SupersedesDIN 4984-10:1987-06www.beuth.deDocument comprises 12 pagesIn case of doubt, the German-language original s
4、hall be considered authoritative.01.15A comma is used as the decimal marker. Contents Page National foreword 3 National Annex NA (informative) Bibliography 4 1 Scope . 5 2 Normative references 5 3 Dimensions 5 3.1 General 5 3.2 Tool holder style N for rhombic indexable insert shape D 6 3.3 Tool hold
5、er style N for triangular indexable insert shape T . 8 4 Designation . 9 5 Material . 10 6 Design . 10 6.1 Type of mounting 10 6.2 Corner radius, r10 6.3 Thickness, s, of indexable insert . 11 7 Extent of delivery . 11 8 Marking 11 Bibliography . 12 2DIN ISO 5610-10:2015-02 National foreword This do
6、cument (EN ISO 5610-10:2014) has been prepared by Technical Committee ISO/TC 29 “Small tools”, Subcommittee SC 9 “Tools with defined cutting edges, cutting items” (Secretariat: DIN, Germany). The responsible German body involved in its preparation was the DIN-Normenausschuss Werkzeuge und Spannzeuge
7、 (DIN Standards Committee Tools and Clamping Devices), Working Committee NA 121-01-12 AA Dreh- und Bohrwerkzeuge mit Wendeschneidplatten aus harten Schneidstoffen. This is the first edition of the DIN ISO 5610 series, and replaces the DIN 4984 series, which was the basis for this series of Internati
8、onal Standards. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. DIN and/or DKE shall not be held responsible for identifying any or all such patent rights. DIN ISO 5610 consists of the following parts, under the general title Tool
9、 holders with rectangular shank for indexable inserts: Part 1: General survey, correlation and determination of dimensions Part 2: Style A Part 3: Style B Part 4: Style D Part 5: Style F Part 6: Style G Part 7: Style J Part 8: Style K Part 9: Style L Part 10: Style N Part 11: Style R Part 12: Style
10、S Part 13: Style T Part 14: Style H Part 15: Style V The DIN Standard corresponding to the International Standard referred to in this document is as follows: ISO 6987 DIN ISO 6987 Amendments This standard differs from DIN 4984-10:1987-06 as follows: a) the text of the International Standard has been
11、 adopted without any modification. Previous editions DIN 4984-10: 1980-04, 1987-06 DIN ISO 5610-10:2015-02 3National Annex NA (informative) Bibliography DIN 4000-1, Tabular layouts of properties Part 1: Concepts and principles DIN 4000-76, Tabular layouts of properties Part 76: Inserts, indexable DI
12、N 4000-77, Tabular layouts of properties Part 77: Inserts, clamped, for grooving, parting and thread machining DIN 4000-90, Tabular layouts of properties Part 90: Tool holders for indexable inserts DIN 4967-1, Indexable hardmetal inserts with rounded corners, with partly cylindrical hole 7 normal cl
13、earance DIN 4967-2, Indexable hardmetal inserts with rounded corners, with partly cylindrical hole 11 normal clearance DIN 4968, Indexable hardmetal inserts with rounded corners, without fixation hole DIN 4969-1, Ceramic indexable inserts, with rounded corners, without fixing hole DIN 4983, Tool hol
14、ders with rectangular shank and cartridges for indexable inserts Presentation of the designation DIN 4988, Indexable hardmetal inserts with rounded corners, with cylindrical fixation hole DIN 6580, Terminology of chip removing Movements and geometry of the chip removing process DIN 6581, Terminology
15、 of chip removing Reference systems and angles on the cutting part of the tool DIN 6582, Terminology of cutting Additional terms for the tool, wedge and the cutting edge DIN 6584, Terms of the cutting technique Forces, energy, work, power DIN ISO 6987, Indexable hard material inserts with rounded co
16、rners, with partly cylindrical fixing hole Dimensions ISO/TS 13399-201, Cutting tool data representation and exchange Part 201: Creation and exchange of 3D models Regular inserts ISO/TS 13399-202, Cutting tool data representation and exchange Part 202: Creation and exchange of 3D models Irregular in
17、serts DIN ISO 5610-10:2015-02 4Tool holders with rectangular shank for indexable inserts Part 10: Style N1 ScopeThis part of ISO 5610 specifies tool holders with rectangular shank, style N, i.e. with straight shank and cutting edge angle r= 63 for side cutting.These tool holders are primarily intend
18、ed for indexable inserts made of hard metal or other cutting materials to be mounted by clamping and to be used for turning operations.NOTE The symbols for the dimensions shown in the tables of this part of ISO 5610 and the corresponding preferred symbols of properties defined in ISO/TS 13399-2 and
19、ISO/TS 13399-3 are given in ISO 5610-1:2014, Table A.1.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest e
20、dition of the referenced document (including any amendments) applies.ISO 5608:2012, Turning and copying tool holders and cartridges for indexable inserts DesignationISO 5610-1:2014, Tool holders with rectangular shank for indexable inserts Part 1: General survey, correlation and determination of dim
21、ensions3 Dimensions3.1 GeneralIt is not necessary for tool holders to comply with the pictorial representation; only the dimensions given shall be observed.For determination of dimensions h1, f, and l1, see ISO 5610-1.For explanation of the designation code for tool holders, see ISO 5608.NOTE The va
22、lues of rake angles and inclination angles shown in the figures are recommended values; they can vary according to the application.DIN ISO 5610-10:2015-02 53.2 Tool holder style N for rhombic indexable insert shape DKeyaInclination angle, s.bRake angle, o.cNeutral tool holders, note cof Table 1.NOTE
23、 This figure shows a right-hand tool holder (R); left-hand tool holder (L) laterally reversed.Figure 1 Tool holder style N for rhombic indexable insert DDIN ISO 5610-10:2015-02 6Table 1Dimensions in millimetresSymbolah1b l3f h2l1al2sbjs13 h13 +050,h13 k16 max.SDNCR 0808 078 8 7,75 4 8 25 2,38SDNCL 0
24、808 07SDNCN 0808 07cSDNCR 1010 0710 10 7,75 5 10 25 2,38SDNCL 1010 07SDNCN 1010 07cSDNCR 1212 0712 12 7,75 6 12 25 2,38SDNCL 1212 07SDNCN 1212 07cSDNCR 1616 1116 16 11,6 8 16 32 3,97SDNCL 1616 11SDNCN 1616 11cSDNCR 2020 1120 20 11,6 10 20 32 3,97SDNCL 2020 11SDNCN 2020 11cSDNCR 2020 1520 20 15,5 10
25、20 404,76SDNCL 2020 15SDNCN 2020 15cPDNNR 2020 156,35PDNNL 2020 15SDNCR 2525 1525 25 15,5 12,5 25 404,76SDNCL 2525 15SDNCN 2525 15cPDNNR 2525 156,35PDNNL 2525 15SDNCR 3225 1532 25 15,5 12,5 32 404,76SDNCL 3225 15SDNCN 3225 15cPDNNR 3225 156,35PDNNL 3225 15SDNCR 4032 1540 32 15,5 16 40 404,76SDNCL 40
26、32 15SDNCN 4032 15cPDNNR 4032 156,35PDNNL 4032 15aFor the selection of length, l1, the dash can be replaced by the dimensions of ISO 5610-1:2014, Table 2. For letter symbols identifying the tool length, see ISO 5608:2012, Table 6.bInsert thickness without shim, if applicable.cTool holder for use in
27、both directions of feed. The cutting edge angle r= 62,5 1 and the tolerances 0,25 mm on dimension f apply for this design.DIN ISO 5610-10:2015-02 73.3 Tool holder style N for triangular indexable insert shape TKeyaInclination angle, s.bRake angle, o.cTool holder style with feed of insert in both dir
28、ections.NOTE This figure shows a right-hand tool holder (R); left-hand tool holder (L) laterally reversed.Figure 2 Tool holder style N for triangular indexable insert TDIN ISO 5610-10:2015-02 8Table 2Dimensions in millimetresSymbolah1b l3f h2l1al2sbjs13 h13 +050,h13 k16 max.STNCR 2525 1625 25 16,5 1
29、2,5 25 323,97STNCL 2525 16PTNNR 2525 164,76PTNNL 2525 16STNCR 2525 2225 25 22 12,5 25 32 4,76STNCL 2525 22PTNNR 2525 22PTNNL 2525 22STNCR 3225 1632 25 16,5 12,5 32 323,97STNCL 3225 16PTNNR 3225 164,76PTNNL 3225 16STNCR 3225 2232 25 22 12,5 32 36 4,76STNCL 3225 22PTNNR 3225 22PTNNL 3225 22STNCR 4032
30、2240 32 22 16 40 36 4,76STNCL 4032 22PTNNR 4032 22PTNNL 4032 22aFor the selection of length, l1, the dash can be replaced by the dimensions of ISO 5610-1:2014, Table 2. For letter symbols identifying the tool length, see ISO 5608:2012, Table 6.bInsert thickness without shim, if applicable.4 Designat
31、ionA tool holder in accordance with this part of ISO 5610 shall be designated by the following:a) “Tool holder”;b) a reference to this part of ISO 5610 (i.e. ISO 5610-10);c) type of mounting, in accordance with ISO 5608;d) symbol for indexable insert shape, in accordance with ISO 5608;e) symbol for
32、tool style, in accordance with ISO 5608;f) symbol for the indexable insert normal clearance, in accordance with ISO 5608;g) symbol for hand of tool, in accordance with ISO 5608;h) its height, h1, width, b, and length, l1(symbol for tool length in accordance with ISO 5608);i) its cutting edge length,
33、 l3.DIN ISO 5610-10:2015-02 9EXAMPLE 1 Tool holder for a horizontally mounted bore-clamped (P) rhombic indexable insert shape D (D), tool holder style N (N), for normal clearance of indexable insert n= 0 (N), right-hand type (R), with height h1= 40 mm and width b = 32 mm (4032), length l1= 170 mm (P
34、), for cutting edge length l3= 15,5 mm (15) is designated as follows:Tool holder ISO 5610-10 - PDNNR 4032 P15EXAMPLE 2 Tool holder for a horizontally mounted bore-clamped (P) triangular indexable insert shape T (T), tool holder style N (N), for normal clearance of indexable insert n= 0 (N), right-ha
35、nd type (R), with height h1= 40 mm and width b = 32 mm (4032), length l1= 150 mm (M), for cutting edge length l3= 22 mm (22) is designated as follows:Tool holder ISO 5610-10 - PTNNR 4032 M225 MaterialThe material should be steel with a tensile strength of at least 1 200 N/mm2.6 Design6.1 Type of mou
36、ntingStandard design of tool holders with indexable insert shall be mounted in accordance with Tables 1 and 2.Other types of mounting are at the manufacturers discretion or upon agreement. The letter symbol in the designation, symbol 1, shall then be replaced by the respective symbol for the chosen
37、or agreed-upon type of mounting in accordance with ISO 5608.For the modified type of mounting deviating from Tables 1 and 2, the relevant indexable insert thickness shall also be considered.6.2 Corner radius, rTool holders in accordance with this part of ISO 5610 can be equipped with inserts with cu
38、tting edge length, l3, as specified in Tables 1 and 2, and any corner radius, r.The values for l1given in ISO 5610-1:2014, Table 2, apply to tool holders with inserts having corner radii, r, in accordance with Table 3.Table 3Dimensions in millimetresl3r7,75 0,411,60,815,516,522NOTE The values given
39、for rare nominal values. The accurate values converted from the inch dimensions are 0,397 mm and 0,794 mm.For indexable inserts with corner radii, r, other than those specified in Table 3, the dimensions f and l1shall be determined in accordance with ISO 5610-1.The tolerances for h1, f, and l1refer
40、to dimensions measured with master indexable insert and master shim, if applicable.DIN ISO 5610-10:2015-02 106.3 Thickness, s, of indexable insertThe values for thickness, s, given in Tables 1 and 2, apply to indexable inserts without shim and for the standard design of tool holders.For tool holders
41、 for indexable inserts with thicknesses deviating from the specified values, the thickness shall be indicated when ordering or upon delivery (in the handbook).7 Extent of deliveryTool holders shall be delivered complete with clamping device, but without indexable insert(s).8 MarkingTool holders shal
42、l be marked with the letter symbol and the name or trademark of the manufacturer.Additional marking is at the manufacturers discretion or upon agreement.Deviations in marking may be by mutual agreement.A reference to this part of ISO 5610, i.e. ISO 5610-10:2014, shall be given on the packaging.DIN I
43、SO 5610-10:2015-02 11Bibliography1 ISO 883, Indexable hardmetal (carbide) inserts with rounded corners, without fixing hole Dimensions2 ISO 3002-1, Basic quantities in cutting and grinding Part 1: Geometry of the active part of cutting tools General terms, reference systems, tool and working angles,
44、 chip breakers3 ISO 3364, Indexable hardmetal (carbide) inserts with rounded corners, with cylindrical fixing hole Dimensions4 ISO 6987, Indexable hard material inserts with rounded corners, with partly cylindrical fixing hole Dimensions5 ISO/TS 13399-2, Cutting tool data representation and exchange Part 2: Reference dictionary for the cutting items6 ISO/TS 13399-3, Cutting tool data representation and exchange Part 3: Reference dictionary for tool itemsDIN ISO 5610-10:2015-02 12