1、April 2016 English price group 11No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 53.040.20!%Q“2469725www.din.deDIN
2、EN ISO 283Textile conveyor belts Full thickness tensile strength, elongation at break and elongation at the reference load Test method (ISO 283:2015);English version EN ISO 283:2015,English translation of DIN EN ISO 283:2016-04Textilfrdergurte Zugfestigkeit bei voller Gurtdicke, Bruchdehnung und Deh
3、nung bei breitenbezogener Bruchkraft Prfverfahren (ISO 283:2015);Englische Fassung EN ISO 283:2015,Englische bersetzung von DIN EN ISO 283:2016-04Courroies transporteuses carcasse textile Rsistance la traction, allongement la rupture et allongement sous force de rfrence en pleine paisseur Mthode des
4、sai (ISO 283:2015);Version anglaise EN ISO 283:2015,Traduction anglaise de DIN EN ISO 283:2016-04SupersedesDIN EN ISO 283:2008-02www.beuth.deDocument comprises 17 pagesDTranslation by DIN-Sprachendienst.In case of doubt, the German-language original shall be considered authoritative.04.16 DIN EN ISO
5、 283:2016-04 2 A comma is used as the decimal marker. National foreword This document (EN ISO 283:2015) has been prepared by Technical Committee ISO/TC 41 “Pulleys and belts (including veebelts)” (Secretariat: SAC, China), Subcommittee SC 3 “Conveyor belts” (Twin Secretariat: SAC, China and JISC, Ja
6、pan) and has been taken over as EN ISO 283:2015 by Technical Committee CEN/TC 188 “Conveyor belts” (Secretariat: SNV, Switzerland). The responsible German body involved in its preparation was DIN-Normenausschuss Kautschuktechnik (DIN Standards Committee Rubber Technology), Working Committee NA 045-0
7、2-05 AA Frdergurte. This standard is not suitable or valid for light conveyor belts as described in DIN EN ISO 21183-1. The DIN Standards corresponding to the International Standards referred to in this document are as follows: ISO 7500-1 DIN EN ISO 7500-1 ISO 21183-1 DIN EN ISO 21183-1 Amendments T
8、his standard differs from DIN EN ISO 283:2008-02 as follows: a) the standard has been technically and editorially revised; b) Clause 2 has been updated; c) Figures 3, 4 and 5 have been revised. Previous editions DIN 22109: 1973-02 DIN 22109-2: 1979-08 DIN 22109-6: 1988-02 DIN EN ISO 283-1: 2001-01 D
9、IN EN ISO 283: 2008-02 DIN EN ISO 283:2016-04 3 National Annex NA (informative) Bibliography DIN EN ISO 7500-1, Metallic materials Verification of static uniaxial testing machines Part 1: Tension/compression testing machines Verification and calibration of the force-measuring system DIN EN ISO 21183
10、-1, Light conveyor belts Part 1: Principal characteristics and applications DIN EN ISO 283:2016-04 4 This page is intentionally blank EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 283 November 2015 ICS 53.040.20 Supersedes EN ISO 283:2007English Version Textile conveyor belts - Full thick
11、ness tensile strength, elongation at break and elongation at the reference load - Test method (ISO 283:2015) Courroies transporteuses carcasse textile - Rsistance la traction, allongement la rupture et allongement sous force de rfrence en pleine paisseur - Mthode dessai (ISO 283:2015) Textilfrdergur
12、te - Zugfestigkeit bei voller Gurtdicke, Bruchdehnung und Dehnung bei breitenbezogener Bruchkraft - Prfverfahren (ISO 283:2015) This European Standard was approved by CEN on 24 October 2015. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for
13、giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three
14、official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodie
15、s of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spa
16、in, Sweden, Switzerland, Turkey andUnited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of exploitation in any form and by any means reserved worldwide
17、 for CEN national Members. Ref. No. EN ISO 283:2015 EEuropean foreword 31 Scope . 52 Normative references 53 Terms and definitions . 54 Principle 65 Apparatus . 66 Test pieces . 76.1 Shape and dimensions 76.2 Method of selection of test pieces 76.3 Preparation of test pieces . 106.4 Number of test p
18、ieces 106.5 Conditioning of test pieces 107 Procedure 108 Calculation and expression of results 108.1 Tensile strength . 108.2 Elongation 118.2.1 Elongation at break . 118.2.2 Elongation at reference force (see 3.5) 119 Test report 11Bibliography . 13Contents PageDIN EN ISO 283:2016-04 EN ISO 283:20
19、15 (E)2Foreword 4European foreword This document (EN ISO 283:2015) has been prepared by Technical Committee ISO/TC 41 “Pulleys and belts (including veebelts)” in collaboration with Technical Committee CEN/TC 188 “Conveyor belts” the secretariat of which is held by SNV. This European Standard shall b
20、e given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2016, and conflicting national standards shall be withdrawn at the latest by May 2016. Attention is drawn to the possibility that some of the elements of this document may be
21、 the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 283:2007. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to imp
22、lement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romani
23、a, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 283:2015 has been approved by CEN as EN ISO 283:2015 without any modification. DIN EN ISO 283:2016-04 EN ISO 283:2015 (E)3 ForewordISO (the International Organization for Standardizat
24、ion) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be r
25、epresented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to d
26、evelop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the
27、ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified durin
28、g the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meani
29、ng of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information.The committee responsible for this document is ISO/TC 41,
30、Pulleys and belts (including veebelts), Subcommittee SC 3, Conveyor belts.This fourth edition cancels and replaces the third edition (ISO 283:2007), which has been technically revised.DIN EN ISO 283:2016-04 EN ISO 283:2015 (E)4 1 ScopeThis International Standard specifies a test method for the deter
31、mination of the full thickness tensile strength in the longitudinal direction and the elongation at the reference force and breaking point of conveyor belts having a textile carcass. The method can also be used for the determination of full thickness tensile strength in the transverse direction and
32、the elongation at the breaking point, for use when the manufacturer is requested by the purchaser to state values for these properties.This International Standard is not suitable or valid for light conveyor belts as described in ISO 21183-1.2 Normative referencesThe following documents, in whole or
33、in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 75001, Metallic materials Verification of
34、 static uniaxial testing machines Part 1: Tension/compression testing machines Verification and calibration of the force-measuring systemISO 18573, Conveyor belts Test atmospheres and conditioning periods3 Terms and definitionsFor the purposes of this document, the following terms and definitions ap
35、ply.3.1tensile strengthgreatest measured force during the tensile test divided by the width of the test pieceNote 1 to entry: It is expressed in N/mm.3.2nominal tensile strengthspecified minimum value of the tensile strengthNote 1 to entry: It is expressed in N/mm.3.3reference forcereference loadone
36、-tenth of the nominal tensile strength in the longitudinal direction multiplied by the width of the test piece in mmEXAMPLE Nominal tensile strength = 1 600 N/mm; one tenth of the nominal tensile strength = 160 N/mm; reference force for 25 mm test piece = 25 mm 160 N/mm = 4 000 N.Note 1 to entry: It
37、 is expressed in N/mm.DIN EN ISO 283:2016-04 EN ISO 283:2015 (E)5 3.4elongation at breakelongation at the greatest force (load)Note 1 to entry: It is expressed as the percentage increase in the distance between two reference points.3.5elongation at the reference force (load)elongation at the referen
38、ce force (load) in the longitudinal directionNote 1 to entry: It is expressed as the percentage increase in the distance between two reference points.4 PrincipleA test piece, cut from the full thickness of the conveyor belt, is extended under specified conditions using a tensile testing machine, unt
39、il rupture of the test piece occurs.5 Apparatus5.1 Tensile testing machine, of CRE or CRT type, calibrated to Grade 1 according to ISO 7500-1 and capable of extending the test piece at a constant rate, without interruption, of (100 10) mm/min.5.2 Device, such as an extensometer, with a measuring len
40、gth of at least 100 mm and accurate to within 0,1 mm or better, capable of measuring the elongation of the gauge length marked on the test piece. Use of a device that produces a graphical trace throughout the test is preferred.5.3 Grips, the form of which should prevent any slippage of the test piec
41、e during the tensile test. The use of grips with transverse serrations in accordance with Figure 1 is recommended.Dimensions in millimetres3050Figure 1 Grip with transverse serrations5.4 Die cutter or power saw, either of the dies with wall profiles as shown in Figure 2 being suitable for cutting th
42、e test pieces shown in Figure 3, Figure 4, and Figure 5. Other profiles may be used, but the critical feature is that the cut sides of the test piece are perpendicular to the test piece surfaces.DIN EN ISO 283:2016-04 EN ISO 283:2015 (E)6 6 Test pieces6.1 Shape and dimensionsThe shape and dimensions
43、 of the test piece shall be in accordance with Figure 3, Figure 4, Figure 5, or Figure 6.6.2 Method of selection of test piecesTest pieces shall be selected parallel, or at right angles, to the axis of the belt, and at not less than 50 mm from the edge of the belt. If test pieces are selected from a
44、 sample cut from the belt, no test piece shall be cut with its longitudinal edge less than 12 mm from the edge of the sample. In all cases, the cut or sawn sides of the test piece shall be perpendicular to its surface. No test piece shall contain a ply joint.For a test piece of type D, draw the form
45、 of the test piece on the surface of the belt or sample and from each edge of the sample, cut at five places with a power saw up to the drawn lines (see Figure 6).The type D test piece illustrated in Figure 6 should be limited to the testing of conveyor belts having tensile strengths greater than 2
46、000 N/mm.Dimensions in millimetres18a)5511=b)Figure 2 Suitable die profilesDIN EN ISO 283:2016-04 EN ISO 283:2015 (E)7 Dimensions in millimetres100(220 10) + L351R1 000+1-225KeyL length of both grips1 reference linesFigure 3 Type A test pieceDimensions in millimetres+1-225100(415 10) + L100R5601KeyL
47、 length of both grips1 reference linesFigure 4 Type B test pieceDIN EN ISO 283:2016-04 EN ISO 283:2015 (E)8 Dimensions in millimetres+1-225100(240 10) + L63R3501KeyL length of both grips1 reference linesFigure 5 Type C test pieceDimensions in millimetres(415 10) + L100 150 125 11,5 0,5R560 112+1-225100KeyL length of both grips1 reference lines2 cutting points across the warpFigure 6 Type D test pieceDIN EN ISO 283:2016-04 EN ISO 283:2015 (E)9 6.3 Preparation of
