1、May 2011 Translation by DIN-Sprachendienst.English price group 8No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 21.
2、060.10!$phm“1776974www.din.deDDIN EN ISO 14585Hexalobular socket pan head tapping screws (ISO 14585:2011)English translation of DIN EN ISO 14585:2011-05Flachkopf-Blechschrauben mit Innensechsrund (ISO 14585:2011)Englische bersetzung von DIN EN ISO 14585:2011-05Vis tle tte cylindrique bombe large six
3、 lobes internes (ISO 14585:2011)Traduction anglaise de DIN EN ISO 14585:2011-05SupersedesDIN EN ISO 14585:2002-05 andDIN EN ISO 14585 Corrigendum1:2006-03www.beuth.deDocument comprises pagesIn case of doubt, the German-language original shall be considered authoritative.1104.11 DIN EN ISO 14585:2011
4、-05 A comma is used as the decimal marker. National foreword This standard has been prepared by Technical Committee ISO/TC 2 “Fasteners” in collaboration with Technical Committee CEN/TC 185 “Fasteners” (Secretariat: DIN, Germany). The responsible German body involved in its preparation was the Norme
5、nausschuss Mechanische Verbindungselemente (Fasteners Standards Committee), Working Committee NA 067-00-05 AA Klein-schrauben und gewindeformende Schrauben. The DIN Standards corresponding to the International Standards referred to in this document are as follows: ISO 225 DIN EN ISO 225 ISO 1478 DIN
6、 EN ISO 1478 ISO 2702 DIN EN ISO 2702 ISO 3269 DIN EN ISO 3269 ISO 4042 DIN EN ISO 4042 ISO 4759-1 DIN EN ISO 4759-1 ISO 10664 DIN EN ISO 10664 ISO 10683 DIN EN ISO 10683 Amendments This standard differs from DIN EN ISO 14585:2002-05 and DIN EN ISO 14585 Corrigendum 1:2006-03 as follows: a) Corrigen
7、dum 1:2006 has been incorporated (Table 1, dimension rmin instead of rmax and column Type F: l = 13 mm instead of l = 13,5 mm) ; b) normative references are now undated; c) in Table 2, non-electrolytically applied zinc flake coatings have been added; d) Annex ZA has been deleted. Previous editions D
8、IN EN ISO 14585: 2002-05 DIN EN ISO 14585 Corrigendum 1: 2006-03 2 DIN EN ISO 14585:2011-05 National Annex NA (informative) Bibliography DIN EN ISO 225, Fasteners Bolts, screws, studs and nuts Symbols and descriptions of dimensions DIN EN ISO 1478, Tapping screw thread DIN EN ISO 2702, Heat-treated
9、steel tapping screws Mechanical properties DIN EN ISO 3269, Fasteners Acceptance inspection DIN EN ISO 4042, Fasteners Electroplated coatings DIN EN ISO 4759-1, Tolerances for fasteners Part 1: Bolts, screws, studs and nuts Product grades A, B and C DIN EN ISO 10664, Hexalobular internal driving fea
10、ture for bolts and screws DIN EN ISO 10683, Fasteners Non-electrolytically applied zinc flake coatings 3 DIN EN ISO 14585:2011-05 4 This page is intentionally blank EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 14585 February 2011 ICS 21.060.10 Supersedes EN ISO 14585:2001English Version
11、Hexalobular socket pan head tapping screws (ISO 14585:2011) Vis tle tte cylindrique bombe large six lobes internes (ISO 14585:2011) Flachkopf-Blechschrauben mit Innensechsrund (ISO 14585:2011) This European Standard was approved by CEN on 17 January 2011. CEN members are bound to comply with the CEN
12、/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Cen
13、tre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as th
14、e official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,Portugal, Romania,
15、 Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worl
16、dwide for CEN national Members. Ref. No. EN ISO 14585:2011: EEN ISO 14585:2011 (E) 2 DIN EN ISO 14585:2011-05 Contents Page Foreword3 1 Scope .4 2 Normative references 4 3 Dimensions .5 4 Specifications and reference International Standards 7 5 Designation .7 EN ISO 14585:2011 (E) 3 Foreword This do
17、cument (EN ISO 14585:2011) has been prepared by Technical Committee ISO/TC 2 Fasteners in collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identi
18、cal text or by endorsement, at the latest by August 2011, and conflicting national standards shall be withdrawn at the latest by August 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held res
19、ponsible for identifying any or all such patent rights. This document supersedes EN ISO 14585:2001. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, C
20、yprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO
21、 14585:2011 has been approved by CEN as a EN ISO 14585:2011 without any modification. DIN EN ISO 14585:2011-05 ”“1 Scope This International Standard specifies the characteristics of hexalobular socket pan head tapping screws with thread sizes from ST2,9 to ST6,3 inclusive. If, in special cases, spec
22、ifications other than those listed in this International Standard are required, they can be selected from existing International Standards, for example ISO 1478, ISO 2702, ISO 4759-1. 2 Normative references The following referenced documents are indispensable for the application of this document. Fo
23、r dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 225, Fasteners Bolts, screws, studs and nuts Symbols and descriptions of dimensions ISO 1478, Tapping screws thread ISO 2702, Heat-treated
24、 steel tapping screws Mechanical properties ISO 3269, Fasteners Acceptance inspection ISO 4042, Fasteners Electroplated coatings ISO 4759-1, Tolerances for fasteners Part 1: Bolts, screws, studs and nuts Product grades A, B and C ISO 10664, Hexalobular internal driving feature for bolts and screws I
25、SO 10683, Fasteners Non-electrolytically applied zinc flake coatings 4EN ISO 14585:2011 (E) DIN EN ISO 14585:2011-05 3 Dimensions See Figure 1 and Table 1. Symbols and descriptions of dimensions are specified in ISO 225. Type C Type F Type R Figure 1 5EN ISO 14585:2011 (E) DIN EN ISO 14585:2011-05 T
26、able 1 Dimensions Dimensions in millimetres Thread sizes ST2,9 ST3,5 ST4,2 ST4,8 ST5,5 ST6,3 Pa1,1 1,3 1,4 1,6 1,8 1,8 a 1,1 1,3 1,4 1,6 1,8 1,8 damax. 3,5 4,1 4,9 5,6 6,3 7,3 nom. = max. 5,6 7,00 8,00 9,50 11,00 12,00 dkmin. 5,3 6,64 7,64 9,14 10,57 11,57 nom. = max. 2,4 2,6 3,1 3,7 4,0 4,6 k min.
27、2,15 2,35 2,8 3,4 3,7 4,3 r min. 0,1 0,1 0,2 0,2 0,25 0,25 rf 5 6 6,5 8 9 10 Type C 2,6 3,2 3,7 4,3 5 6 Type F 2,1 2,5 2,8 3,2 3,6 3,6 y ref. Type R 2,7 3,2 3,6 4,3 5 Socket No. 10 15 20 25 25 30 A ref. 2,8 3,35 3,95 4,5 4,5 5,6 max. 1,27 1,40 1,80 2,03 2,03 2,42 Hexalobular socket t min. 1,01 1,14
28、1,42 1,65 1,65 2,02 lbType F Type C and Type R nom. min. max. min. max. 4,5 3,7 5,3 3,7 4,5 6,5 5,7 7,3 5,7 6,5 9,5 8,7 10,3 8,7 9,5 13 12,2 13,8 12,2 13,0 16 15,2 16,8 15,2 16,0 19 18,2 19,8 18,2 19,0 22 21,2 22,8 20,7 22,0 25 24,2 25,8 23,7 25,0 32 30,7 33,3 30,7 32,0 38 36,7 39,3 36,7 38,0 45 43,
29、7 46,3 43,5 45,0 50 48,7 51,3 48,5 50,0 NOTE Preferred lengths are the ones between the bold stepped lines. aP is the pitch of the thread. bSizes with lengths marked with a dash () in this table cannot be manufactured. 6EN ISO 14585:2011 (E) DIN EN ISO 14585:2011-05 4 Specifications and reference In
30、ternational Standards See Table 2. Table 2 Specifications and reference International Standards Material Steel, as specified in ISO 2702 Thread International Standard ISO 1478 Mechanical properties International Standard ISO 2702 Product grade A Tolerances International Standard ISO 4759-1 Hexalobul
31、ar socket International Standard ISO 10664 Finish Coating As processed Requirements for electroplating are specified in ISO 4042. Requirements for non-electrolytically applied zinc flake coatings are specified in ISO 10683. Additional requirements or other finishes or coatings shall be agreed betwee
32、n the supplier and the purchaser. Acceptability Acceptance inspection is specified in ISO 3269. 5 Designation EXAMPLE A hexalobular socket pan head tapping screw with thread size ST3,5, nominal length l = 16 mm, round end Type R is designated as follows: Tapping screw ISO 14585 - ST3,5 16 - R 7EN ISO 14585:2011 (E) DIN EN ISO 14585:2011-05
