1、November 2015English price group 16No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 71.100.30!%GFC“2363532www.din.de
2、DIN EN 16263-4Pyrotechnic articles Other pyrotechnic articles Part 4: Test methods;English version EN 16263-4:2015,English translation of DIN EN 16263-4:2015-11Pyrotechnische Gegenstnde Sonstige pyrotechnische Gegenstnde Teil 4: Prfverfahren;Englische Fassung EN 16263-4:2015,Englische bersetzung von
3、 DIN EN 16263-4:2015-11Articles pyrotechniques Autres articles pyrotechniques Partie 4: Mthodes dessai;Version anglaise EN 16263-4:2015,Traduction anglaise de DIN EN 16263-4:2015-11www.beuth.deDTranslation by DIN-Sprachendienst.In case of doubt, the German-language original shall be considered autho
4、ritative.Document comprises 38 pages10.15 DIN EN 16263-4:2015-11 2 A comma is used as the decimal marker. National foreword This document (EN 16263-4:2015) has been prepared by Technical Committee CEN/TC 212 “Pyro-technic articles” (Secretariat: NEN, Netherlands). The responsible German body involve
5、d in its preparation was the DIN-Normenausschuss Materialprfung (Materials Testing Standards Committee), Working Committee NA 062-08-81 AA Pyrotechnische Gegenstnde. The DIN Standards corresponding to the International Standards referred to in this document are as follows: ISO 2859-1 DIN ISO 2859-1
6、ISO 6344-3 DIN ISO 6344-3 ISO 21948 DIN ISO 21948 National Annex NA (informative) Bibliography DIN ISO 2859-1, Sampling procedures for inspection by attributes Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection DIN ISO 6344-3, Coated abrasives Grain size ana
7、lysis Part 3: Determination of grain size distribution of macrogrits P 240 to P 2500 DIN ISO 21948, Coated abrasives Plain sheets EN 16263-4August 2015 ICS 71.100.30 English VersionPyrotechnic articles - Other pyrotechnic articles -Test 4: Test methods Articles pyrotechniques - Autres articles pyrot
8、echniques - Partie 4: Mthodes dessai Pyrotechnische Gegenstnde - Sonstige pyrotechnische Gegenstnde - Teil 4: Prfverfahren This European Standard was approved by CEN on 12 May 2015. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving th
9、is European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official
10、versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Aust
11、ria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Swede
12、n, Switzerland, Turkey andUnited Kingdom. CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16263-4:2015 EEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEUROPEAN C
13、OMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGContents Page European foreword .4 1 Scope 5 2 Normative references 5 3 Terms and definitions .5 4 Apparatus .5 4.1 General 5 4.2 Test area .5 4.2.1 General 5 4.2.2 Indoor 6 4.2.3 Outdoor .6 4.3 Timing device .6
14、4.4 Calliper 6 4.5 Ruler 6 4.6 Measuring tape .6 4.7 Wind speed meter 6 4.8 Balance .6 4.9 Temperature chamber .6 4.10 Sound level meter 7 4.11 Shock apparatus 7 4.12 Drop-test apparatus .7 4.13 Goniometer .7 4.14 Devices for measuring of effect height .7 4.15 Devices for measuring thrust .7 4.16 Ab
15、rasive sheet .8 4.17 Witness screen .8 4.18 Transparent type size sheet .9 4.19 High speed video equipment 9 4.20 Further test apparatus .9 5 Test methods . 10 5.1 General . 10 5.2 Construction 10 5.2.1 Outer dimension of item 10 5.2.2 Determination of calibre . 10 5.2.3 Determination of gross mass
16、10 5.3 Design verification 10 5.3.1 General . 10 5.3.2 Conformity to drawings and part lists 10 5.3.3 Pyrotechnic composition Determination of net explosive content 10 5.4 Angle of ascent and height of effects . 11 5.4.1 General . 11 5.4.2 Apparatus 11 5.4.3 Procedure 11 5.5 Measurement of sound pre
17、ssure level . 12 5.5.1 Apparatus 12 5.5.2 Procedure 12 5.6 Timing measurement 12 5.6.1 Apparatus 12 5.6.2 Procedure 12 5.7 Mechanical conditioning 12 DIN EN ISO 16263-4:2015-11 EN ISO 16263-4:2015 (E) 25.7.1 Apparatus . 12 5.7.2 Procedure . 12 5.8 Mechanical impact test (Drop test) 13 5.8.1 Apparatu
18、s . 13 5.8.2 General . 13 5.8.3 Procedure . 13 5.9 Thermal conditioning 13 5.9.1 Apparatus . 13 5.9.2 Procedure . 13 5.10 Function test 14 5.10.1 General . 14 5.10.2 Apparatus . 14 5.10.3 Procedure . 15 5.11 Measurement of thrust 16 5.11.1 Apparatus . 16 5.11.2 Procedure . 16 5.12 Resistance to igni
19、tion by an abrasive surface . 16 5.12.1 Apparatus . 16 5.12.2 Procedure . 16 5.13 Further tests . 16 5.13.1 Sensitiveness of pyrotechnic composition 16 5.13.2 External temperature of hand-held pyrotechnic articles . 19 5.14 Measuring of labelling . 19 5.14.1 Apparatus . 19 5.14.2 Procedure . 19 5.15
20、 Measuring of the energy of fragments 20 5.15.1 Apparatus . 20 5.15.2 Procedure . 20 5.16 Water immersion test 21 5.16.1 Apparatus . 21 5.16.2 Procedure . 21 Annex A (informative) Mechanical conditioning (Shock apparatus) . 22 Annex B (informative) Drop test (Mechanical impact test) . 25 Annex C (in
21、formative) Procedures for calculation of heights 26 Annex D (informative) Determination of the duration of accelerated ageing test to demonstrate the correct functioning at the use by date 30 Annex E (informative) Overview of essential safety requirements and corresponding clauses of all parts of EN
22、 16263 . 33 Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 2007/23/EC on the placing on the market of pyrotechnic articles 34 Annex ZB (informative) Relationship between this European Standard and the Essential Requirements of EU Dir
23、ective 2013/29/EU on the placing on the market of pyrotechnic articles 35 Bibliography 36 DIN EN ISO 16263-4:2015-11EN ISO 16263-4:2015 (E)3European foreword This document (EN 16263-4:2015) has been prepared by Technical Committee CEN/TC 212 “Pyrotechnic articles”, the secretariat of which is held b
24、y NEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2016, and conflicting national standards shall be withdrawn at the latest by February 2016. Attention is drawn to the possibility th
25、at some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Associatio
26、n, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA or Annex ZB, which are an integral part of this document. This European standard is one of the series of standards as listed below: EN 16263-1, Pyrotechnic articles Other pyrote
27、chnic articles Part 1: Terminology; EN 16263-2, Pyrotechnic articles Other pyrotechnic articles Part 2: Requirements; EN 16263-3, Pyrotechnic articles Other pyrotechnic articles Part 3: Categories and types; EN 16263-4, Pyrotechnic articles Other pyrotechnic articles Part 4: Test methods; EN 16263-5
28、, Pyrotechnic articles Other pyrotechnic articles Part 5: Minimum labelling requirements and instructions for use. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulga
29、ria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Tur
30、key and the United Kingdom. DIN EN ISO 16263-4:2015-11 EN ISO 16263-4:2015 (E) 41 Scope This European Standard specifies test methods for other pyrotechnic articles (except pyrotechnic articles for vehicles, cartridges for powder actuated tools and ignition devices). 2 Normative references The follo
31、wing documents, in whole or in part, are referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 16263-1:2015, Pyrotechnic
32、 articles Other pyrotechnic articles Part 1: Terminology EN 16263-2:2015, Pyrotechnic articles Other pyrotechnic articles Part 2: Requirements EN 16263-3:2015, Pyrotechnic articles Other pyrotechnic articles Part 3: Categories and types EN 16263-5:2015, Pyrotechnic articles Other pyrotechnic article
33、s Part 5: Minimum labelling requirements and instructions for use EN 61672-1, Electroacoustics Sound level meters Part 1: Specifications (IEC 61672-1) EN ISO 13385-1, Geometrical product specifications (GPS) Dimensional measuring equipment Part 1: Callipers; Design and metrological characteristics (
34、ISO 13385-1) EN ISO 13385-2, Geometrical product specifications (GPS) Dimensional measuring equipment Part 2: Calliper depth gauges; Design and metrological characteristics (ISO 13385-2) ISO 6344-3, Coated abrasives Grain size analysis Part 3: Determination of grain size distribution of microgrits P
35、240 to P2500 ISO 21948, Coated abrasives Plain sheets 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 16263-1:2015 apply. NOTE Wherever reference is made to a pyrotechnic article only other pyrotechnic articles (not including those for vehicles, cartr
36、idges for powder actuated tools and ignition devices) are meant, as it is the scope of this standard. 4 Apparatus 4.1 General Any equivalent apparatus with the same accuracy or better may be used. 4.2 Test area 4.2.1 General The test area shall be unobstructed, non-flammable and suitable for the acc
37、urate measurement of the required parameters. The test sample should be placed in the centre of the test area, as shown in the labelled instruction. The manufacturers supplied or recommended equipment shall be used. DIN EN ISO 16263-4:2015-11EN ISO 16263-4:2015 (E)54.2.2 Indoor The test area shall b
38、e indoors. The test area shall be in an enclosed space, which is capable of limiting the movement of air. A means of extracting fumes shall be provided where necessary. 4.2.3 Outdoor The test area shall be an outdoor site. If applicable, provisions shall be made at the centre of the test area for pa
39、rtially burying into the ground. If applicable, insert support pole in the centre of the test area. Before starting the function test start the measurement of the wind speed with a wind speed meter (4.7) and continue measuring during the whole function test. A means of measuring the wind speed at a
40、height of 1,5 m above the ground shall be provided. If applicable, no performance testing shall be carried out if the wind speed exceeds 5,0 m/s. 4.3 Timing device Timing device, capable of being read to the nearest 0,1 s. 4.4 Calliper Calliper, flat faced vernier calliper reading to 0,1 mm (conform
41、ing to EN ISO 13385-1 and EN ISO 13385-2). 4.5 Ruler Ruler, reading to 1,0 mm. 4.6 Measuring tape Measuring tape, reading to 10 mm. 4.7 Wind speed meter Wind speed meter capable of measuring to an accuracy of at least 0,5 m/s. 4.8 Balance 4.8.1 Balance, read to 0,1 g. 4.8.2 Balance, read to 0,01 g.
42、4.9 Temperature chamber The temperature chamber(s) shall comply with the following specifications: up to 75 C or 1,25 times the maximum use temperature of the test samples in degrees Celsius (if higher than 60 C); when required, down to 10 C lower than the minimum use temperature of the test samples
43、; when required, capability of developing the highest level of humidity specified by the manufacturer. DIN EN ISO 16263-4:2015-11 EN ISO 16263-4:2015 (E) 6The tolerance on each of the above temperature requirements is 2,5 C. The required test conditions may be delivered by means of a single temperat
44、ure chamber or by means of two or more chambers, each capable of delivering one or more of the specified sets of conditions. 4.10 Sound level meter Sound level meter of class 1 of EN 61672-1 with free-field microphone. 4.11 Shock apparatus The apparatus shall provide a deceleration of 490 m/s2(50/+1
45、00) m/s2(when measured at the centre of an unloaded platform) and the mechanical conditioning impulse duration (time elapsed from the starting of the machines deceleration to the time in which the deceleration reaches its maximum value during each first shock pulse) shall be 2 ms 1 ms working at a f
46、requency of 1 Hz 0,1 Hz. An example of an apparatus is shown in Annex A. 4.12 Drop-test apparatus The drop test apparatus shall comply with the following specifications: drop height 1,2 m; ground plate with a thickness greater than 10 mm of steel. An example of an apparatus is shown in Annex B. 4.13
47、 Goniometer Goniometer, reading to 1. 4.14 Devices for measuring of effect height The devices shall be capable of measuring horizontal and/or vertical angles: universal surveying instrument (USI); theodolite; electronic level or clinometers; video systems measuring grid. 4.15 Devices for measuring t
48、hrust Either of the following apparatus shall be used for the measurement of thrust: calibrated strain gauge; piezoelectric type load cell. The accuracy of these gauges shall be determined as a function of levels of thrusts to be measured and the tolerances given by the manufacturer. DIN EN ISO 1626
49、3-4:2015-11EN ISO 16263-4:2015 (E)74.16 Abrasive sheet Abrasive sheet, large enough to permit striking of the ignition head, conforming to ISO 21948, grit P240 conforming to ISO 6344-3. 4.17 Witness screen For the assessment of fragments according to 5.15.2.2, the following equipment shall be used: sturdy square based frame: length: 1 m; width: 1 m; height: 0,5 m, or alter
