1、September 2016 English price group 12No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 23.040.70!%3b“2561663www.din.d
2、eDIN EN 853Rubber hoses and hose assemblies Wire braid reinforced hydraulic type Specification;English version EN 853:2015,English translation of DIN EN 853:2016-09Gummischluche und schlauchleitungen Hydraulikschluche mit Drahtgeflechteinlage Spezifikation;Englische Fassung EN 853:2015,Englische ber
3、setzung von DIN EN 853:2016-09Tuyaux et flexibles en caoutchouc Type hydraulique avec armature de fils mtallique tresss Spcification;Version anglaise EN 853:2015,Traduction anglaise de DIN EN 853:2016-09SupersedesDIN EN 853:199702www.beuth.deDocument comprises 21 pagesDTranslation by DIN-Sprachendie
4、nst.In case of doubt, the German-language original shall be considered authoritative.09.16 DIN EN 853:2016-09 2 A comma is used as the decimal marker. National foreword This document (EN 853:2015) has been prepared by Technical Committee CEN/TC 218 “Rubber and plastics hoses and hose assemblies” (Se
5、cretariat: BSI, United Kingdom). The responsible German body involved in its preparation was DIN-Normenausschuss Elastomer-Technik (DIN Standards Committee Elastomer Technology), Working Committee NA 045-02-12 AA Gummi- und Kunststoffschluche sowie Schlauchleitungen (Spiegelgremium zu CEN/TC 218; IS
6、O/TC 45/SC 1). NOTE Requirements for hydraulic hoses for underground mining are dealt with in separate standards. The DIN Standards corresponding to the International Standards referred to in this document are as follows: ISO 1817:2005 DIN ISO 1817:2008-08 ISO 23529 DIN ISO 23529 Amendments This sta
7、ndard differs from DIN EN 853:1997-02 as follows: a) Clause 2 has been updated; b) in Subclause 5.1, Table 1, the tolerances for inside diameters have been updated; c) in Subclause 6.8, details of abrasion resistance testing have been modified; d) a new normative Annex A has been added; e) a new nor
8、mative Annex B has been added; f) a new informative Annex C has been added; Previous editions DIN 20022-1: 1977-01, 1987-02 DIN 20022-2: 1970-08, 1977-01, 1987-02 DIN 20022-3: 1978-11, 1987-02 DIN 20022-4: 1978-11, 1987-02 DIN EN 853: 1997-02 DIN EN 853:2016-09 3 National Annex NA (informative) Bibl
9、iography DIN ISO 1817:2008-08, Rubber, vulcanized Determination of the effect of liquids (ISO 1817:2005) DIN ISO 23529, Rubber General procedures for preparing and conditioning test pieces for physical test methods DIN EN 853:2016-09 4 This page is intentionally blank EUROPEAN STANDARD NORME EUROPEN
10、NE EUROPISCHE NORM EN 853 April 2015 ICS 23.100.40; 23.040.70 Supersedes EN 853:1996English Version Rubber hoses and hose assemblies - Wire braid reinforced hydraulic type - Specification Tuyaux et flexibles en caoutchouc - Type hydraulique avec armature de fils mtallique tresss - Spcification Gummi
11、schluche und -schlauchleitungen - Hydraulikschluche mit Drahtgeflechteinlage - SpezifikationThis European Standard was approved by CEN on 31 January 2015. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the st
12、atus of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French,
13、German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cro
14、atia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
15、United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No.
16、 EN 853:2015 EEN 853:2015 (E) 2 Contents Page Foreword 3 1 Scope 4 2 Normative references 4 3 Types of hoses .5 4 Materials and construction .5 4.1 Hoses 5 4.2 Hose assemblies 5 5 Dimensions .5 5.1 Diameters and concentricity .5 5.2 Length .7 5.2.1 Hoses 7 5.2.2 Hose assemblies 7 6 Requirements .8 6
17、.1 Hydrostatic requirements .8 6.2 Minimum bend radius 9 6.3 Impulse test requirements 9 6.4 Leakage of hose assemblies 9 6.5 Cold flexibility . 10 6.6 Adhesion between components 10 6.7 Vacuum resistance . 10 6.8 Abrasion resistance . 11 6.9 Fluid resistance. 11 6.9.1 Test pieces 11 6.9.2 Oil resis
18、tance 11 6.9.3 Water based fluid resistance . 11 6.9.4 Water resistance . 11 6.10 Ozone resistance 11 7 Designation . 11 8 Marking 12 8.1 Hoses . 12 8.2 Hose assemblies . 12 Annex A (normative) Procedure for the measurement of abrasion 13 A.1 Apparatus 13 A.2 Method . 14 A.3 Test pieces 14 A.4 Condi
19、tion of test pieces . 14 A.5 Procedure 15 A.6 Expression of results . 15 A.7 Test report . 15 Annex B (normative) Type and routine testing of production hoses . 16 Annex C (informative) Production acceptance testing . 17 DIN EN 853:2016-09 EN 853:2015 (E) 3 Foreword This document (EN 853:2015) has b
20、een prepared by Technical Committee CEN/TC 218 “Rubber and plastics hoses and hose assemblies”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 201
21、5 and conflicting national standards shall be withdrawn at the latest by October 2015. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights.
22、 This document supersedes EN 853:1996. In comparison with EN 853:1996, the following significant changes have been made: updated normative references; tolerances for inside diameter in Table 1; added Annex A; added Annex B; added Annex C. According to the CEN-CENELEC Internal Regulations, the nation
23、al standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithu
24、ania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 853:2016-09 EN 853:2015 (E) 4 1 Scope This European Standard specifies requirements for four types of wire braid reinforced hoses and hose as
25、semblies of nominal bore from 5 to 51. They are suitable for use with: hydraulic fluids in accordance with ISO 6743-4 with the exception of HFD R, HFD S and HFD T at temperatures ranging from -40 C to +100 C; water based fluids at temperatures ranging from -40 C to +70 C; water at temperatures rangi
26、ng from 0 C to +70 C. This European Standard does not include requirements for end fittings. It is limited to the performance of hoses and hose assemblies. NOTE 1 The hoses are not suitable for use with castor oil based and ester based fluids. NOTE 2 Hoses and hose assemblies are not be operated out
27、side the limits of this standard. NOTE 3 Requirements for hydraulic hoses for underground mining are standardized in separate standards. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dat
28、ed references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN ISO 1302, Geometrical Product Specifications (GPS) - Indication of surface texture in technical product documentation (ISO 1302) EN ISO 1402:200
29、9, Rubber and plastics hoses and hose assemblies - Hydrostatic testing (ISO 1402:2009) EN ISO 4671, Rubber and plastics hoses and hose assemblies - Methods of measurement of the dimensions of hoses and the lengths of hose assemblies (ISO 4671) EN ISO 6743-4, Lubricants, industrial oils and related p
30、roducts (class L) - Classification - Part 4: Family H (Hydraulic systems) (ISO 6743-4) EN ISO 6803, Rubber or plastics hoses and hose assemblies - Hydraulic-pressure impulse test without flexing (ISO 6803) EN ISO 7233, Rubber and plastics hoses and hose assemblies - Determination of resistance to va
31、cuum (ISO 7233) EN ISO 7326, Rubber and plastics hoses - Assessment of ozone resistance under static conditions (ISO 7326) EN ISO 8033:2006, Rubber and plastics hoses - Determination of adhesion between components (ISO 8033) EN ISO 10619-2, Rubber and plastics hoses and tubing - Measurement of flexi
32、bility and stiffness - Part 2: Bending tests at sub-ambient temperatures (ISO 10619-2) ISO 1817:2005, Rubber, vulcanized - Determination of the effect of liquids ISO 23529, Rubber - General procedures for preparing and conditioning test pieces for physical test methods DIN EN 853:2016-09 EN 853:2015
33、 (E) 5 3 Types of hoses Four types of hoses are specified: 1) Type 1ST - hoses with a single braid of wire reinforcement; 2) Type 2ST - hoses with two braids of wire reinforcement; 3) Type 1SN - hoses with a single braid of wire reinforcement; 4) Type 2SN - hoses with two braids of wire reinforcemen
34、t. Types 1SN and 2SN shall be of the same reinforcement construction as types 1ST and 2ST, except that they shall have thinner covers designed to assemble with fittings that do not require removal of the cover or a portion of the cover. 4 Materials and construction 4.1 Hoses Hoses shall consist of a
35、n oil and water resistant synthetic rubber lining, one or two layers of high tensile steel wire and an oil and weather resistant rubber cover. 4.2 Hose assemblies Hose assemblies shall only be manufactured with those hose fittings whose functionality has been verified in accordance with subclauses 6
36、.1, 6.3, 6.4 and 6.5 of this European Standard. 5 Dimensions 5.1 Diameters and concentricity When measured in accordance with EN ISO 4671, the diameters of the hoses shall conform to the values given in Table 1. DIN EN 853:2016-09 EN 853:2015 (E) 6 Table 1 Diameters of hoses Dimensions in millimetre
37、s except nominal bore Nominal bore All types Type 1ST Type 1SN Type 2ST Type 2SN Inside diameter Diameter over reinforcement Outside diameter of hose Outside diameter of hose Cover thickness Diameter over reinforcement Outside diameter of hose Outside diameter of hose Cover thickness min. max. min.
38、max. min. max. max. min. max. min. max. min. max. max. min. max. 5 4,9 5,4 9,0 10,0 11,9 13,5 12,5 0,8 1,5 10,6 11,6 15,1 16,7 14,1 0,8 1,5 6 6,4 7,0 10,6 11,6 15,1 16,7 14,1 0,8 1,5 12,1 13,3 16,7 18,3 15,7 0,8 1,5 8 7,9 8,5 12,1 13,3 16,7 18,3 15,7 0,8 1,5 13,7 14,9 18,3 19,9 17,3 0,8 1,5 10 9,5 1
39、0,1 14,5 15,7 19,0 20,6 18,1 0,8 1,5 16,1 17,3 20,6 22,2 19,7 0,8 1,5 12 12,7 13,5 17,5 19,1 22,2 23,8 21,4 0,8 1,5 19,0 20,6 23,8 25,4 23,0 0,8 1,5 16 15,8 16,7 20,6 22,2 25,4 27,0 24,5 0,8 1,5 22,2 23,8 27,0 28,6 26,2 0,8 1,5 19 18,8 19,8 24,6 26,2 29,4 31,0 28,5 0,8 1,5 26,2 27,8 31,0 32,6 30,1 0
40、,8 1,5 25 25,4 26,4 32,5 34,1 37,1 39,1 36,6 0,8 1,5 34,1 35,7 38,5 40,9 38,9 1,0 2,0 31 31,8 33,0 39,3 41,7 44,4 47,6 44,8 1,0 2,0 43,3 45,7 49,2 52,4 49,5 1,0 2,0 38 38,1 39,3 45,6 48,0 50,8 54,0 52,1 1,5 2,5 49,6 52,0 55,6 58,8 55,9 1,3 2,5 51 50,6 52,0 58,7 61,7 65,1 68,3 65,5 1,5 2,5 62,3 64,7
41、68,2 71,4 68,6 1,3 2,5 DIN EN 853:2016-09 EN 853:2015 (E) 7 When measured in accordance with EN ISO 4671, the concentricity of the hoses shall conform to the values given in Table 2. Table 2 Concentricity of hoses Dimensions in millimetres, except nominal bore Nominal bore Maximum variation in wall
42、thickness Between inside diameter and outside diameter Between inside diameter and reinforcement diameter All types Types 1ST and 1SN Types 2ST and 2SN Up to and including 6 0,8 0,4 0,4 Over 6 and including 19 1,0 0,6 0,7 Over 19 1,3 0,8 0,9 5.2 Length 5.2.1 Hoses Hoses shall be supplied in lengths
43、as specified by the purchaser, subject to a tolerance on the specified lengths of 2 %. When no specific hose lengths have been ordered, the percentages of different lengths in any given delivery shall be as follows: over 20 m : not less than 80 % of total length; over 10 m to 20 m : not more than 20
44、 % of total length; 1 m to 10 m : not more than 3 % of total length. The length of hose shall be at least 1 m. 5.2.2 Hose assemblies The tolerances on the length of hose assemblies shall conform to Table 3. DIN EN 853:2016-09 EN 853:2015 (E) 8 Table 3 Tolerances of length of hose assemblies Nominal
45、bore Up to and including 25 Over 25 and including 50 Over 50 Hose assembly length mm Tolerance Tolerance Tolerance Up to and including 630 + 7 mm - 3 mm + 12 mm - 4 mm + 25 mm - 6 mm Over 630 and including 1 250 + 12 mm - 4 mm + 20 mm - 6 mm Over 1 250 and including 2 500 + 20 mm - 6 mm + 25 mm - 6
46、mm Over 2 500 and including 8 000 + 1,5 % - 0,5 % Over 8 000 + 3 % - 1 % 6 Requirements 6.1 Hydrostatic requirements 6.1.1 When tested in accordance with EN ISO 1402, the maximum working pressure, the proof pressure and burst pressure of the hoses and hose assemblies shall conform to the values give
47、n in Table 4. 6.1.2 When tested in accordance with EN ISO 1402, the change in length of hose at the maximum working pressure shall not exceed +2 % to -4 %. Table 4 Maximum working pressure, proof pressure and burst pressure Nominal bore Maximum working pressure bar aProof pressure bar Burst pressure
48、 bar Types 1ST and 1SN Types 2ST and 2SN Types 1ST and 1SN Types 2ST and 2SN Types 1ST and 1SN Types 2ST and 2SN 5 250 415 500 830 1 000 1 650 6 225 400 450 800 900 1 600 8 215 350 430 700 850 1 400 10 180 330 360 660 720 1 320 12 160 275 320 550 640 1 100 16 130 250 260 500 520 1 000 19 105 215 210
49、 430 420 850 25 88 165 175 325 350 650 31 63 125 150 250 250 500 38 50 90 100 180 200 360 51 40 80 80 160 160 320 a1 bar = 0,1 MPa. DIN EN 853:2016-09 EN 853:2015 (E) 9 6.2 Minimum bend radius When bent to the minimum bend radius given in Table 5 measured on the inside of the bend, the flatness shall not exceed 10 % of the original outside diameter. Measure the hose outside diameter with a calliper before bending the hose. Bend the ho
