欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    CSA C22 2 NO 40-M1989-1989 Cutout Junction and Pull Boxes (Fourth Edition General Instruction No 1 April 1989 General Instruction No 2 March 1992).pdf

    • 资源ID:621324       资源大小:888.04KB        全文页数:46页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    CSA C22 2 NO 40-M1989-1989 Cutout Junction and Pull Boxes (Fourth Edition General Instruction No 1 April 1989 General Instruction No 2 March 1992).pdf

    1、C22.2 No. 40-M1989(reaffirmed 2014)Cutout, Junction, and Pull BoxesLegal Notice for StandardsCanadian Standards Association (operating as “CSA Group”) develops standards through a consensus standards development process approved by the Standards Council of Canada. This process brings together volunt

    2、eers representing varied viewpoints and interests to achieve consensus and develop a standard. Although CSA Group administers the process and establishes rules to promote fairness in achieving consensus, it does not independently test, evaluate, or verify the content of standards.Disclaimer and excl

    3、usion of liabilityThis document is provided without any representations, warranties, or conditions of any kind, express or implied, including, without limitation, implied warranties or conditions concerning this documents fitness for a particular purpose or use, its merchantability, or its non-infri

    4、ngement of any third partys intellectual property rights. CSA Group does not warrant the accuracy, completeness, or currency of any of the information published in this document. CSA Group makes no representations or warranties regarding this documents compliance with any applicable statute, rule, o

    5、r regulation. IN NO EVENT SHALL CSA GROUP, ITS VOLUNTEERS, MEMBERS, SUBSIDIARIES, OR AFFILIATED COMPANIES, OR THEIR EMPLOYEES, DIRECTORS, OR OFFICERS, BE LIABLE FOR ANY DIRECT, INDIRECT, OR INCIDENTAL DAMAGES, INJURY, LOSS, COSTS, OR EXPENSES, HOWSOEVER CAUSED, INCLUDING BUT NOT LIMITED TO SPECIAL O

    6、R CONSEQUENTIAL DAMAGES, LOST REVENUE, BUSINESS INTERRUPTION, LOST OR DAMAGED DATA, OR ANY OTHER COMMERCIAL OR ECONOMIC LOSS, WHETHER BASED IN CONTRACT, TORT (INCLUDING NEGLIGENCE), OR ANY OTHER THEORY OF LIABILITY, ARISING OUT OF OR RESULTING FROM ACCESS TO OR POSSESSION OR USE OF THIS DOCUMENT, EV

    7、EN IF CSA GROUP HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, INJURY, LOSS, COSTS, OR EXPENSES.In publishing and making this document available, CSA Group is not undertaking to render professional or other services for or on behalf of any person or entity or to perform any duty owed by any pe

    8、rson or entity to another person or entity. The information in this document is directed to those who have the appropriate degree of experience to use and apply its contents, and CSA Group accepts no responsibility whatsoever arising in any way from any and all use of or reliance on the information

    9、contained in this document. CSA Group is a private not-for-profit company that publishes voluntary standards and related documents. CSA Group has no power, nor does it undertake, to enforce compliance with the contents of the standards or other documents it publishes. Intellectual property rights an

    10、d ownershipAs between CSA Group and the users of this document (whether it be in printed or electronic form), CSA Group is the owner, or the authorized licensee, of all works contained herein that are protected by copyright, all trade-marks (except as otherwise noted to the contrary), and all invent

    11、ions and trade secrets that may be contained in this document, whether or not such inventions and trade secrets are protected by patents and applications for patents. Without limitation, the unauthorized use, modification, copying, or disclosure of this document may violate laws that protect CSA Gro

    12、ups and/or others intellectual property and may give rise to a right in CSA Group and/or others to seek legal redress for such use, modification, copying, or disclosure. To the extent permitted by licence or by law, CSA Group reserves all intellectual property rights in this document.Patent rightsAt

    13、tention is drawn to the possibility that some of the elements of this standard may be the subject of patent rights. CSA Group shall not be held responsible for identifying any or all such patent rights. Users of this standard are expressly advised that determination of the validity of any such paten

    14、t rights is entirely their own responsibility.Authorized use of this documentThis document is being provided by CSA Group for informational and non-commercial use only. The user of this document is authorized to do only the following:If this document is in electronic form:sLOADTHISDOCUMENTONTOACOMPU

    15、TERFORTHESOLEPURPOSEOFREVIEWINGITsSEARCHANDBROWSETHISDOCUMENTANDsPRINTTHISDOCUMENTIFITISIN0$ it consisted of 37 pages, each dated April 1989. Errata to Clause 4.8.1 and Table 2 are incorporated (and identified by a vertical line in the margin) in the attached replacement pages. GSA Standard C22.2 No

    16、. 40-M1989 now consists of the following pages: 318, 2128, and 3137 dated April 1989; and 19, 20, 29, and 30 dated March 1992. These replacement pages are to be inserted into your copy of the Standard; the pages replaced should be kept for reference. the edge of the metal and only slightly longer th

    17、an the width of the strip. The acceptability of formed hinges made of materials other than steel shall be determined by special investigation. 4.6.1.8 Hinges of the ear-type shall not be used where the spacing between them would be more than 650 mm, regardless of the thickness of the metal used. Not

    18、e: This type of hinge consists of projections at the ends of opposite side or end walls and corresponding projections in flanges on the cover. Rivets or bolts serve as hinge pins to connect adjacent projections on wall and cover respectively. 4.6.1.9 Hinge pins without heads shall be upset or secure

    19、d in place in an equivalent way. 4.6.2 Nonmetallic Enclosures Hinges shall be constructed to permit the opening and closing of the door (refer to Clause 4.5.2). Note: It is intended that the reliability of membrane-type hinges will be determined by this requirement. Hinges may form either an integra

    20、l part or be considered an add-on. 4.7 Latches and Handles 4.7.1 Metal Enclosures 4.7.1.1 Doors shall be provided with at least one latch which shall have adequate strength and a positive action that prevents the doors from jarring open due to any vibration that they are likely to be subjected to du

    21、ring normal use. 4.7.1.2 Latches shall be securely fastened in place by not fewer than two screws, rivets, spot welds, or some acceptable equivalent. 4.7.1.3 Single doors more than 1220 mm in length shall be provided with a minimum of two latches that secure the doors at points nearest the ends. Dou

    22、bledoors that overlap shall be secured by a minimum of two latches, one located at each end. L1atches are only required on the door that closes last. Doubledoors that do not overlap shall have two latches per door, one located at each end of each door. 4.7.1.4 Where a door has all its edges flanged

    23、and does not exceed 457 mm in width or length, a latch may consist of: (a) a button stamped in the side wall of the box that engages an indentation or closefitting hole in the cover flange; or (b) a button stamped on the cover flange that engages an indentation or closefitting hole in the side wall

    24、of the box. 4.7.1.5 Except where latches of the pintumbler or selflocking types are used, knobs, door handles, or an approved equivalent shall be C22.2 No. 40M1989 March 1992 Page 19 (Replaces p. 19, April 1989) provided for the opening Of doors. 4.1.2 Nonmetallic Enclosures Latches shall provide a

    25、positive fastening action. Note: Latches may form either an integral part or be considered an add-on. 4.8 Covers 4.8.1* Metal Enclosures Covers, unless hinged directly to the side wall of the box, shall be secured by no less than four fastenings, except that two screws, one at the centre of eac shor

    26、t side, may be used to fasten a cover no larger than 32 900 mm , provided that no dimension of the cover is greater than 216 mm. *Effectjve Date-March 31, 1992 4.8.2 Nonmetallic Enclosures 4.8.2.1 Covers for junction or pull boxes shall be of the blank-type only. 4.8.2.2 Covers shall be a minimum of

    27、 4.37 and an average of 4.76 mm thick. 4.8.2.3 Mating surfaces of a cover and box shall provide a close fit. A gasket, if required to provide a close fit, shall be provided with the cover but need not be cemented or otherwise secured in place on the cover. 4.8.2.4 Screws provided to attach covers sh

    28、all be made of brass, bronze, or steel. If made of steel, they shall be protected against corrosion. Screws shall be not smaller than No. 6, have no more than 32 threads per 25.4 mm, and shall engage at least 2 full threads in the cover. 4.9 Knockouts and Twistouts 4.9.1 Metal Boxes 4.9.1.1 Where kn

    29、ockouts are punched from the material of the box proper, they shall be cleancut and, after being planished, shall not protrude more than (approximately) 50% of the thickness of the metal at any point on their circumference. 4.9.1.2 Where multiple arrangements consisting of a single knockout combined

    30、 with twistouts are used, each shall be held by ties at least 3.17 mm wide, and the ties shall be arranged to make it unlikely that any other than the desired opening will be made. This will ordinarily require one or more extra ties for the twistouts, and staggering of the ties. See Clause 6.4 of CS

    31、A Standard C22.2 No. 0 for the test requirements for a single knockout surrounded by multiple twistouts. C22.2 No. 40M1989 March 1992 Page 20 (Replaces p. 20, April 1989) shown in Figure 2, with the dimensions shown in Table 10. Before the gauge is used, the knockout shall be removed and, when neces

    32、sary, the remaining tab shall be filed or ground flush with the surface of the box, inside and outside the box, as well as at the edge surrounding the opening. An appropriate trade size gauge shall be used, offset from the centre of the knockout in a direction opposite to the area to be tested. When

    33、 testing knockouts located adjacent to a box radius, a steel feeler gauge, 0.13 mm thick and 2.5 mm wide, shall be used to check the space between inner box surface and the flat surface of the gauge, as shown in Figure 3. The test gauge shall not be canted or tiltedto make the necessary contact with

    34、 the surface of the box. The ability to insert the steel feeler between the box surface and the gauge surface confirms that the boxs corner radius encroaches on the required flat surface and that the box has failed the test. When testing knockouts or portions of knockouts located away from any radiu

    35、s between two adjacent walls, the steel feeler gauge shall not be used. Note: The purpose of this test is to ensure that a locknut will be seated flush with the surface of the box. 6.3.2 strength of Knockouts A knockout shall remain in place when subjected to a force of 44 N applied at right angles

    36、by means of a mandrel with a 6.4 mm diameter flat end. The mandrel shall be applied at the point most likely to cause movement of the knockout. 6.3.3 Knockouts (Pryouts, Including Breakouts) in Boxes of Nonmetallic Material 6.3.3.1 A knockout shall be removed easily by means of a screwdriver used as

    37、 a chisel, without any sharp edges being left or any damage being caused to the box. The side edge of a screwdriver may be run once along the edge of the knockout opening to remove any fragile tabs remaining along the edge. 6.3.3.2 Boxes that are constructed of a material that is known to be affecte

    38、d by low temperatures shall be conditioned for 5 h at a temperature of 20 2C in circulating air. Immediately after this conditioning, the test described in Clause 6.3.3.1 shall be repeated on a knockout. 6.4 Security of Doors Doors shall be opened and closed 25 times without evidence of cracking or

    39、other indications of material breakdown. C22.2 No. 40M1989 March 1992 Page 29 (Replaces p. 29, April 1989) Table 1 Minimum Thickness for Cast Metal Enclosures (See Clause 4.1.2.1.) Method of Minimum thickness of plain walls, nun Area up to 15 480 mm2 Area over 15 480 nun2 fabrication Length up to 15

    40、2 mm Length over 152 mm Diecast 1.58* 2.38 Other 3.17 3.17 *Area and length limitations may be complied with by subdividing larger areas by means of suitable reinforcing ribs. Table 2t Minimum Thickness of Sheet Metal (See Clause 4.1.2.2.) Maximum siz largest sur e of face Minimum mm thickness, Leng

    41、th or width, mm Ajea, m Steel Stainless steel* Aluminum 610 0.232 1.34 1.06 1.84 1016 0.645 1.69 1.34 2.33 2286 1.626 2.35 1.69 3.03 Over 2286 Over 1.626 3.11 2.35 3.81 *Stainless sheet-steel shall comply with ASTM Standard A167. tEffective Date-March 31, 1992 C22.2 No. 40M1989 March 1992 Page 30 (R

    42、eplaces p. 30, April 1989 General Instruction No. 1C22.2 No. 40-M1989April 1989Title: Cutout, Junction, and Pull BoxesPagination: 37 pages, each dated April 1989To register for e-mail notification about any updates to this publicationgo to shop.csa.caclick on CSA Update ServiceThe List ID that you w

    43、ill need to register for updates to this publication is 2002373.If you require assistance, please e-mail techsupportcsagroup.org or call 416-747-2233.Visit CSA Groups policy on privacy at csagroup.org/legal to find out how we protect your personal information.Canadian Standards Association C22.2 No.

    44、 40-M1989 Cutout, Junction, and Pull Boxes Wiring Products Forming Part of Canadian Electrical Code, Part II Safety Standards for Electrical Equipment ISSN 0317-5669 Published in April 1989 by Canadian Standards Association (Incorporated 1919) 178 Rexdale Boulevard Rexdale (Toronto), Ontario Canada

    45、M9W 1R3 Technical Editor: Christopher Harding Managing Editor: Bernard Kelly Canadian Standards Association1989 All rights reserved. No part of this publication may be reproduced in any form, in an electronic retrieval system or otherwise, without the prior permission of the publisher. Contents Tech

    46、nical Committee on Wiring Products 5 Subcommittee on C22.2 No. 40 7 Preface 8 Foreword 9 1. Scope 11 2. Definitions 11 3. General Requirements 12 4. Construction 13 4.1 Metal Enclosures 13 4.1.1 Material 13 4.1.2 Thickness 13 4.1.3 Reinforcement 13 4.1.4 Rigidity 13 4.1.5 Openings in Enclosures 13 4

    47、.1.6 Seams 14 4.1.7 OnePiece Boxes 14 4.1.8 Fastenings 15 4.1.9 Barriers for Metal Boxes 15 4.1.10 Conduit Hubs 15 4.2 Nonmetallic Enclosures 16 4.2.1 General 16 4.2.2 Mounting Means 16 4.2.3 Screw Mountings 16 4.2.4 ConduitConnection Sockets 16 4.3 Special Purpose Enclosures 16 4.4 Clear Panels 16

    48、4.4.1 Glass Panels 16 4.4.2 Nonglass Panels 17 4.5 Doors 17 4.5.1 Metal Enclosures 17 4.5.2 Nonmetallic Enclosures 17 4.6 Hinges 18 4.6.1 Metal Enclosures 18 4.6.2 Nonmetallic Enclosures 19 4.7 Latches and Handles 19 4.7.1 Metal Enclosures 19 4.7.2 Nonmetallic Enclosures 20 4.8 Covers 20 4.8.1 Metal Enclosures 20 4.8.2 Nonmetallic Enclosures 20 4.9 Knockouts and Twistouts 20 4.9.1 Metal Boxes 20 4.9.2 Metal and Nonmetallic Boxes 21 4.10 Protection Against Corrosion 21 4.11 Bonding 22 4.12 Plates 22 C22.2 No. 40Ml989 April 1989 Page 3 5. Marking 22 Dropping of Burning Particles 24


    注意事项

    本文(CSA C22 2 NO 40-M1989-1989 Cutout Junction and Pull Boxes (Fourth Edition General Instruction No 1 April 1989 General Instruction No 2 March 1992).pdf)为本站会员(proposalcash356)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开