1、BSI Standards PublicationBS ISO 5610-7:2014Tool holders with rectangularshank for indexable insertsPart 7: Style JBS ISO 5610-7:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 5610-7:2014. Itsupersedes BS ISO 5610-7:2010 which is withdrawn.The UK participa
2、tion in its preparation was entrusted to TechnicalCommittee MTE/18, Tools tips and inserts for cutting applications.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract.
3、 Users are responsible for its correctapplication. The British Standards Institution 2014. Published by BSI StandardsLimited 2014ISBN 978 0 580 83615 2ICS 25.100.01Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority
4、of theStandards Policy and Strategy Committee on 31 August 2014.Amendments issued since publicationDate Text affectedBS ISO 5610-7:2014 ISO 2014Tool holders with rectangular shank for indexable inserts Part 7: Style JPorte-plaquette queue rectangulaire pour plaquettes amovibles Partie 7: Forme JINTE
5、RNATIONAL STANDARDISO5610-7Second edition2014-09-01Reference numberISO 5610-7:2014(E)BS ISO 5610-7:2014ISO 5610-7:2014(E)ii ISO 2014 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2014All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized othe
6、rwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeC
7、ase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 5610-7:2014ISO 5610-7:2014(E) ISO 2014 All rights reserved iiiContents PageForeword iv1 Scope . 12 Normative references 13 Dimensions . 13.1 General . 13.2
8、Tool holder style J for rhombic indexable insert shape D 23.3 Tool holder style J for triangular indexable insert shape T 43.4 Tool holder style J for rhombic indexable insert shape V 64 Designation 75 Material 86 Design 86.1 Type of mounting 86.2 Corner radius, r86.3 Thickness, s, of indexable inse
9、rt 97 Extent of delivery . 98 Marking 9Bibliography .10BS ISO 5610-7:2014ISO 5610-7:2014(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried ou
10、t through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO co
11、llaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different appr
12、oval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the
13、subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any
14、trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the
15、 Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for this document is ISO/TC 29, Small tools, Subcommittee SC 9, Tools with defined cutting edges, cutting items.This second edition cancels and replaces the first edition (ISO 5610
16、-7:2010), of which it constitutes a minor revision.ISO 5610 consists of the following parts, under the general title Tool holders with rectangular shank for indexable inserts: Part 1: General survey, correlation and determination of dimensions Part 2: Style A Part 3: Style B Part 4: Style D Part 5:
17、Style F Part 6: Style G Part 7: Style J Part 8: Style K Part 9: Style L Part 10: Style N Part 11: Style R Part 12: Style S Part 13: Style Tiv ISO 2014 All rights reservedBS ISO 5610-7:2014ISO 5610-7:2014(E) Part 14: Style H Part 15: Style V ISO 2014 All rights reserved vBS ISO 5610-7:2014BS ISO 5610
18、-7:2014Tool holders with rectangular shank for indexable inserts Part 7: Style J1 ScopeThis part of ISO 5610 specifies tool holders with rectangular shank, style J, i.e. with offset shank and cutting edge angle r= 93 for side cutting.These tool holders are primarily intended for indexable inserts ma
19、de of hard metal or other cutting materials to be mounted by clamping and to be used for turning operations.NOTE The symbols for the dimensions shown in the tables of this part of ISO 5610 and the corresponding preferred symbols of properties defined in ISO/TS 13399-2 and ISO/TS 13399-3 are given in
20、 ISO 5610-1:2014, Table A.1.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced do
21、cument (including any amendments) applies.ISO 5608:2012, Turning and copying tool holders and cartridges for indexable inserts DesignationISO 5610-1:2014, Tool holders with rectangular shank for indexable inserts Part 1: General survey, correlation and determination of dimensions3 Dimensions3.1 Gene
22、ralIt is not necessary for tool holders to comply with the pictorial representation; only the dimensions given shall be observed.For determination of dimensions h1, f, and l1, see ISO 5610-1.For explanation of the designation code for tool holders, see ISO 5608.NOTE The values of rake angles and inc
23、lination angles shown in the figures are recommended values; they can vary according to the application.INTERNATIONAL STANDARD ISO 5610-7:2014(E) ISO 2014 All rights reserved 1BS ISO 5610-7:2014ISO 5610-7:2014(E)3.2 Tool holder style J for rhombic indexable insert shape DKeyaInclination angle, s.bRa
24、ke angle, o.NOTE The figure shows a right-hand tool holder (R); left-hand tool holder (L) laterally reversed.Figure 1 Tool holder style J for rhombic indexable insert DTable 1Dimensions in millimetresSymbolah1b l3f h2l1al2sbjs13 h13 005+ ,h13 k16 max.SDJCR 0808 078 8 7,75 10 8 25 2,38SDJCL 0808 07aF
25、or the selection of length, l1, the dash can be replaced by the dimensions of ISO 5610-1:2014, Table 2. For letter symbols identifying the tool length, see ISO 5608:2012, Table 6.bInsert thickness without shim, if applicable.2 ISO 2014 All rights reservedBS ISO 5610-7:2014ISO 5610-7:2014(E)Symbolah1
26、b l3f h2l1al2sbjs13 h13 005+ ,h13 k16 max.SDJCR 1010 0710 10 7,75 12 10 25 2,38SDJCL 1010 07SDJCR 1212 0712 12 7,75 16 12 25 2,38SDJCL 1212 07SDJCR 1616 1116 16 11,6 20 16 32 3,97SDJCL 1616 11SDJCR 2020 1120 2011,625 20 32 3,97SDJCL 2020 11PDJNR 2020 1515,5 40 6,35PDJNL 2020 15CDJNR 2525 1525 25 15,
27、5 32 25 404,76and7,95CDJNL 2525 15SDJCR 2525 154,76SDJCL 2525 15PDJNR 2525 156,35PDJNL 2525 15CDJNR 3225 1532 25 15,5 32 32 404,76and7,95CDJNL 3225 15SDJCR 3225 154,76SDJCL 3225 15PDJNR 3225 156,35PDJNL 3225 15SDJCR 4032 1540 32 15,5 40 40 404,76SDJCL 4032 15PDJNR 4032 156,35PDJNL 4032 15aFor the se
28、lection of length, l1, the dash can be replaced by the dimensions of ISO 5610-1:2014, Table 2. For letter symbols identifying the tool length, see ISO 5608:2012, Table 6.bInsert thickness without shim, if applicable.Table 1 ISO 2014 All rights reserved 3BS ISO 5610-7:2014ISO 5610-7:2014(E)3.3 Tool h
29、older style J for triangular indexable insert shape TKey1 style of tool holder with indexable insert contact on both sidesaInclination angle, s.bRake angle, o.NOTE The figure shows a right-hand tool holder (R); left-hand tool holder (L) laterally reversed.Figure 2 Tool holder style J for triangular
30、indexable insert T4 ISO 2014 All rights reservedBS ISO 5610-7:2014ISO 5610-7:2014(E)Table 2Dimensions in millimetresSymbolah1b l3f h2l1al2sbjs13 h13 005+ ,h13 k16 max.STJCR 2020 1620 20 16,5 25 20 323,97STJCL 2020 16PTJNR 2020 164,76PTJNL 2020 16CTJNR 2525 1625 25 16,5 32 25 324,76and7,94CTJNL 2525
31、16STJCR 2525 163,97STJCL 2525 16PTJNR 2525 164,76PTJNL 2525 16STJCR 2525 2225 25 22 32 25 36 4,76STJCL 2525 22PTJNR 2525 22PTJNL 2525 22CTJNR 3225 1632 25 16,5 32 32 324,76and7,94CTJNL 3225 16STJCR 3225 163,97STJCL 3225 16PTJNR 3225 164,76PTJNL 3225 16STJCR 3225 2232 25 22 32 32 36 4,76STJCL 3225 22
32、PTJNR 3225 22PTJNL 3225 22STJCR 4032 2240 32 22 40 40 36 4,76STJCL 4032 22PTJNR 4032 22PTJNL 4032 22PTJNR 4032 2740 32 27,5 40 40 40 6,35PTJNL 4032 27aFor the selection of length, l1, the dash can be replaced by the dimensions of ISO 5610-1:2014, Table 2. For letter symbols identifying the tool leng
33、th, see ISO 5608:2012, Table 6.bInsert thickness without shim, if applicable. ISO 2014 All rights reserved 5BS ISO 5610-7:2014ISO 5610-7:2014(E)3.4 Tool holder style J for rhombic indexable insert shape VKeyaInclination angle, s.bRake angle, o.NOTE The figure shows a right-hand tool holder (R); left
34、-hand tool holder (L) laterally reversed.Figure 3 Tool holder style J for rhombic indexable insert V6 ISO 2014 All rights reservedBS ISO 5610-7:2014ISO 5610-7:2014(E)Table 3Dimensions in millimetresSymbolah1b l3f h2l1al2sbjs13 h13 005+ ,h13 k16 max.SVJBR 1212 1112 12 11,1 16 12 25 3,18SVJBL 1212 11S
35、VJCR 1212 11SVJCL 1212 11SVJBR 1616 1116 16 11,1 20 16 25 3,18SVJBL 1616 11SVJCR 1616 11SVJCL 1616 11SVJCR 2020 1120 2011,125 20 25 3,18SVJCL 2020 11SVJBR 2020 1616,6 40 4,76SVJBL 2020 16SVJCR 2525 1125 2511,132 25 25 3,18SVJCL 2525 11SVJBR 2525 1616,6 40 4,76SVJBL 2525 16SVJBR 3225 1632 25 16,6 32
36、32 40 4,76SVJBL 3225 16aFor the selection of length, l1, the dash can be replaced by the dimensions of ISO 5610-1:2014, Table 2. For letter symbols identifying the tool length, see ISO 5608:2012, Table 6.bInsert thickness without shim, if applicable.4 DesignationA tool holder in accordance with this
37、 part of ISO 5610 shall be designated by the following:a) “Tool holder”;b) a reference to this part of ISO 5610 (i.e. ISO 5610-7);c) type of mounting, in accordance with ISO 5608;d) symbol for indexable insert shape, in accordance with ISO 5608;e) symbol for tool style, in accordance with ISO 5608;f
38、) symbol for the indexable insert normal clearance, in accordance with ISO 5608;g) symbol for hand of tool, in accordance with ISO 5608;h) its height, h1, width, b, and length, l1(symbol for tool length in accordance with ISO 5608);i) its cutting edge length, l3.EXAMPLE 1 Tool holder for a screw-cla
39、mped (S) rhombic indexable insert shape D (D), tool holder style J (J), for normal clearance of indexable insert n= 7 (C), right-hand type (R), with height h1= 10 mm and width b = 10 mm (1010), length l1= 70 mm (E), for cutting edge length l3= 7,75 mm (07) is designated as follows: ISO 2014 All righ
40、ts reserved 7BS ISO 5610-7:2014ISO 5610-7:2014(E)Tool holder ISO 5610-7 - SDJCR 1010 E07EXAMPLE 2 Tool holder for a horizontally mounted bore-clamped (P) triangular indexable insert shape T (T), tool holder style J (J), for normal clearance of indexable insert n= 0 (N), right-hand type (R), with hei
41、ght h1= 32 mm and width b = 25 mm (3225), length l1= 170 mm (P), for cutting edge length l3= 16,5 mm (16) is designated as follows:Tool holder ISO 5610-7 - PTJNR 3225 P16EXAMPLE 3 Tool holder for a screw-clamped (S) rhombic indexable insert shape V (V), tool holder style J (J), for normal clearance
42、of indexable insert n= 5 (B), right-hand type (R), with height h1= 20 mm and width b = 20 mm (2020), length l1= 125 mm (K), for cutting edge length l3= 16,6 mm (16) is designated as follows:Tool holder ISO 5610-7 - SVJBR 2020 K165 MaterialThe material should be steel with a tensile strength of at le
43、ast 1 200 N/mm2.6 Design6.1 Type of mountingStandard design of tool holders with indexable insert shall be mounted in accordance with Tables 1 to 3.Other types of mounting are at the manufacturers discretion or upon agreement. The letter symbol in the designation, symbol 1, shall then be replaced by
44、 the respective symbol for the chosen or agreed-upon type of mounting, in accordance with ISO 5608.For the modified type of mounting deviating from Tables 1 to 3, the relevant indexable insert thickness shall also be considered.6.2 Corner radius, rTool holders in accordance with this part of ISO 561
45、0 can be equipped with indexable inserts with cutting edge length, l3, as specified in Tables 1, 2 and 3, and any corner radius, r.The values for l1given in ISO 5610-1:2014, Table 2, apply to tool holders with indexable inserts having corner radii, r, in accordance with Table 4.Table 4Dimensions in
46、millimetresl3r7,750,411,011,111,60,815,516,516,62227,5 1,2NOTE The values given for rare nominal values. The accurate values converted from the inch dimensions are 0,397 mm, 0,794 mm, and 1,191 mm.8 ISO 2014 All rights reservedBS ISO 5610-7:2014ISO 5610-7:2014(E)For indexable inserts with corner rad
47、ii, r, other than those specified in Tables 1 to 3, the dimensions of f and l1shall be determined in accordance with ISO 5610-1.The tolerances for h1, f, and l1refer to dimensions measured with master indexable insert and master shim, if applicable.6.3 Thickness, s, of indexable insertThe values for
48、 thickness, s, given in Tables 1 to 3, apply to indexable inserts without shim and for the standard design of tool holders.For tool holders for indexable inserts with thicknesses deviating from the specified values, the thickness shall be indicated when ordering or upon delivery (in the handbook).7 Extent of deliveryTool holders shall be delivered complete with clamping device, but without indexable insert(s).8 MarkingTool holders shall be marked with the letter symbol and the name or trademark of the manufacturer.Additional marking is at the manufacturers discretion or upon agreement.Devia
