欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    BS ISO 11629-2006 Cranes - Measurement of the mass of a crane and its components《起重机 起重机及其组件质量评估》.pdf

    • 资源ID:583625       资源大小:341.36KB        全文页数:14页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    BS ISO 11629-2006 Cranes - Measurement of the mass of a crane and its components《起重机 起重机及其组件质量评估》.pdf

    1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58ICS 53.020.20Cranes Measurement of the mass of a crane and its componentsBRITISH STANDARDBS ISO 116

    2、29:2004BS ISO 11629:2004This British Standard was published under the authority of the Standards Policy and Strategy Committee on 29 December 2006 BSI 2006ISBN 0 580 49895 6Amendments issued since publicationAmd. No. Date Commentscontract. Users are responsible for its correct application.Compliance

    3、 with a British Standard cannot confer immunity from legal obligations.National forewordThis British Standard was published by BSI. It is the UK implementation of ISO 11629:2004.The UK participation in its preparation was entrusted to Technical Committee MHE/3, Cranes and derricks.A list of organiza

    4、tions represented on MHE/3 can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a Reference numberISO 11629:2004(E)INTERNATIONAL STANDARD ISO11629First edition2004-11-15Cranes Measurement of the mass of a crane and its components Ap

    5、pareils de levage charge suspendue Mesurage de la masse dune grue et de ses composants BS ISO 11629:2004ii iiiContents Page Foreword iv 1 Scope 1 2 Normative references . 1 3 Terms and definitions. 1 4 Apparatus and its accuracy . 1 5 Measuring the mass of the crane as a whole and/or the crane compo

    6、nents . 2 6 Measurement report 3 Annex A (informative) Examples to illustrate how the mass of a crane as a whole and/or its components should be measured. 4 Bibliography . 6 BS ISO 11629:2004iv Foreword ISO (the International Organization for Standardization) is a worldwide federation of national st

    7、andards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International o

    8、rganizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules giv

    9、en in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least

    10、75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 11629 was prepared by Technical Committee ISO/TC 96, Cr

    11、anes, Subcommittee SC 4, Test methods. BS ISO 11629:20041Cranes Measurement of the mass of a crane and its components 1 Scope This International Standard sets forth basic procedures for measuring the mass of a cranes as a whole and/or of its components. This International Standard was prepared in ad

    12、dition to ISO 4310 and covers the types of cranes as defined in ISO 4306-1. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the refere

    13、nced document (including any amendments) applies. ISO 4306-1, Cranes Vocabulary Part 1: General ISO 4310, Cranes Test code and procedures ISO 9373, Cranes and related equipment Accuracy requirements for measuring parameters during testing 3 Terms and definitions For the purposes of this document, th

    14、e terms and definitions given in ISO 4306-1 and the following apply. 3.1 apparatus complete set of equipment and devices required to determine the mass of a crane as a whole and/or of its components 3.2 simple measurement measurement for which the result is read off one measuring device or is the su

    15、m of readings of several measuring devices operating simultaneously 3.3 complex measurement measurement for which the result is the sum of the readings of several measuring devices used sequentially 4 Apparatus and its accuracy 4.1 The following apparatus may be used to measure the mass of a crane a

    16、s a whole and/or of its components: 4.1.1 Scale. BS ISO 11629:20042 4.1.2 Dynamometers, compression or extension. 4.1.3 Supports, knife-edge. 4.1.4 Decking. 4.1.5 Level. 4.1.6 Auxiliary hoist. 4.1.7 Slings, wire rope or chain. 4.2 Measuring apparatus used for measuring the mass of a crane as a whole

    17、 and/or of its components shall be selected in accordance with the accuracy requirements in ISO 9373 and in compliance with national specifications. 4.3 Either simple or complex measurement of the mass of a crane and/or of its components may be used, but simple measurement is preferable. 5 Measuring

    18、 the mass of the crane as a whole and/or the crane components 5.1 The crane, prepared for measuring the mass as a whole or disassembled into its individual components, shall have the equipment required for it to be used as specified in the manufacturers instructions. 5.2 The mass of the crane as a w

    19、hole and/or its components shall be measured by either simple or complex measurements. The reaction forces are measured at points of support by measuring devices (Figures A.1 to A.4). 5.3 When measuring as specified in 5.2, the crane and/or its components shall be placed on the measuring devices as

    20、follows. All measured loads shall be vertical with no induced horizontal forces imparted on the measuring apparatus (Figures A.1 to A.3). The point of support shall be in the centre of the measuring apparatus (Figure A.1). The suspension line shall go through the centre of the mass being measured (F

    21、igure A.2). Decking and knife-edge supports should be placed at the supporting points for a more accurate load transfer from the mass being measured to the measuring apparatus (Figure A.3). For large cranes and/or components, the mass to be measured may be placed sequentially on measuring apparatus

    22、with the support surfaces (the right and left or the front and rear side), while the other side is placed on a firm surface next to measuring apparatus (Figure A.4). 5.4 Each measurement result shall be reduced by the mass of the decking, knife-edge supports, slings and other arrangements, as approp

    23、riate. BS ISO 11629:200436 Measurement report The report on the measurements of the mass of the crane as a whole and/or its components shall include the following data: crane and/or component type; name of the manufacturer; date of the measurement; description of the crane and/or its component; cond

    24、itions of measurement (see section on test conditions as defined in ISO 4310); name of the person supervising the testing. The results of measuring the mass of the crane and/or its components should be tabulated. BS ISO 11629:20044 Annex A (informative) Examples to illustrate how the mass of a crane

    25、 as a whole and/or its components should be measured Key 1 crane 2 scale platform Figure A.1 Measuring the mass of a crane (mobile) as a whole Key 1 slings 2 dynamometer 3 hoist hook 4 crane component Figure A.2 Measuring the mass of a crane component with a dynamometer BS ISO 11629:20045Key 1 knife

    26、-edge support 2 crane component 3 decking 4 compression dynamometer Figure A.3 Measuring the mass of a crane component with compression dynamometers working simultaneously Key 1 supporting surface 2 crane component 3 compression dynamometer Figure A.4 Measuring the mass of a crane component with com

    27、pression dynamometer working sequentially BS ISO 11629:20046 Bibliography 1 ISO 7363, Cranes and lifting appliances Technical characteristics and acceptance documents BS ISO 11629:2004blankBS ISO BSI389 Chiswick High RoadLondonW4 4AL11629:2004BSI British Standards InstitutionBSI is the independent n

    28、ational body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess

    29、the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of

    30、which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and f

    31、oreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI imp

    32、lementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic in

    33、formation services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts

    34、on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi

    35、- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 19

    36、88 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details su

    37、ch as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.


    注意事项

    本文(BS ISO 11629-2006 Cranes - Measurement of the mass of a crane and its components《起重机 起重机及其组件质量评估》.pdf)为本站会员(fuellot230)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开