1、BSI Standards PublicationMulticore and symmetricalpair/quad cables for digital communicationsPart 10: Cables for cords with transmission characteristics up to 2 GHz Sectional specificationBS IEC 61156-10:2016National forewordThis British Standard is the UK implementation of IEC 61156-10:2016.The UK
2、participation in its preparation was entrusted to TechnicalCommittee EPL/46, Cables, wires and waveguides, radio frequency connectors and accessories for communication and signalling.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication doe
3、s not purport to include all the necessary provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 85602 0ICS 33.120.20Compliance with a British Standard cannot confer immunity fromlegal
4、obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April 2016.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS IEC 61156-10:2016IEC 61156-10 Edition 1.0 2016-04 INTERNATIONAL STANDARD Multicore an
5、d symmetrical pair/quad cables for digital communications Part 10: Cables for cords with transmission characteristics up to 2 GHz Sectional specification INTERNATIONAL ELECTROTECHNICAL COMMISSION ICS 33.120.20 ISBN 978-2-8322-3351-1 Registered trademark of the International Electrotechnical Commissi
6、on Warning! Make sure that you obtained this publication from an authorized distributor. BS IEC 61156-10:2016 2 IEC 61156-10:2016 IEC 2016 CONTENTS FOREWORD . 4 1 Scope 6 2 Normative references. 6 3 Terms and definitions 7 4 Installation considerations 7 5 Materials and cable construction 7 6 Charac
7、teristics and requirements . 7 6.1 General remarks . 7 6.2 Electrical characteristics and tests . 8 6.2.1 Conductor resistance . 8 6.2.2 Resistance unbalance 8 6.2.3 Dielectric strength 8 6.2.4 Insulation resistance 8 6.2.5 Mutual capacitance 8 6.2.6 Capacitance unbalance 8 6.2.7 Transfer impedance
8、. 8 6.2.8 Coupling attenuation 8 6.2.9 Current-carrying capacity . 9 6.3 Transmission characteristics . 9 6.3.1 Velocity of propagation (phase velocity) 9 6.3.2 Phase delay and differential delay (delay skew) 9 6.3.3 Attenuation () . 9 6.3.4 Unbalance attenuation (TCL) 10 6.3.5 Near-end crosstalk (N
9、EXT) . 10 6.3.6 Far-end crosstalk (ACR-F) . 11 6.3.7 Alien (exogenous) near-end crosstalk (ANEXT) 11 6.3.8 Alien (exogenous) far-end crosstalk (AFEXT) 12 6.3.9 Alien (exogenous) crosstalk of bundled cables 12 6.3.10 Impedance . 12 6.3.11 Return loss (RL) . 12 6.4 Mechanical and dimensional character
10、istics and requirements . 13 6.4.1 Dimensional requirements 13 6.4.2 Elongation at break of the conductors . 13 6.4.3 Tensile strength of the insulation 13 6.4.4 Elongation at break of the insulation . 13 6.4.5 Adhesion of the insulation to the conductor . 13 6.4.6 Elongation at break of the sheath
11、. 13 6.4.7 Tensile strength of the sheath 13 6.4.8 Crush test of the cable . 13 6.4.9 Impact test of the cable 13 6.4.10 Bending under tension . 13 6.4.11 Repeated bending of the cable . 13 6.4.12 Tensile performance of the cable 14 6.4.13 Shock-test requirements of the cable 14 6.4.14 Bump-test req
12、uirements of the cable 14 6.4.15 Vibration-test requirements of a cable 14 BS IEC 61156-10:2016IEC 61156-10:2016 IEC 2016 3 6.5 Environmental characteristics 14 6.5.1 Shrinkage of insulation . 14 6.5.2 Wrapping test of insulation after thermal ageing 14 6.5.3 Bending test of insulation at low temper
13、ature 14 6.5.4 Elongation at break of the sheath after ageing 14 6.5.5 Tensile strength of the sheath after ageing . 14 6.5.6 Sheath pressure test at high temperature . 14 6.5.7 Cold bend test of the cable . 14 6.5.8 Heat shock test 14 6.5.9 Damp heat steady state 14 6.5.10 Solar radiation (UV test)
14、 . 14 6.5.11 Solvents and contaminating fluids. 15 6.5.12 Salt mist and sulphur dioxide 15 6.5.13 Water immersion 15 6.5.14 Hygroscopicity . 15 6.5.15 Wicking 15 6.5.16 Flame propagation characteristics of a single cable 15 6.5.17 Flame propagation characteristics of bunched cables 15 6.5.18 Halogen
15、 gas evolution 15 6.5.19 Smoke generation 15 6.5.20 Toxic gas emission 15 6.5.21 Integrated fire test 15 7 Bundled cables requirements . 15 8 Introduction to the blank detail specification . 16 Bibliography . 17 Table 1 Coupling attenuation 9 Table 2 Attenuation equation constants 10 Table 3 TCL req
16、uirements 10 Table 4 ELTCTL requirements 10 Table 5 NEXT and PS NEXT requirements . 11 Table 6 ACR-F and PS ACR-F requirements . 11 Table 7 PS ANEXT requirements 11 Table 8 PS AACR-F requirements 12 Table 9 RL requirements 12 BS IEC 61156-10:2016 4 IEC 61156-10:2016 IEC 2016 INTERNATIONAL ELECTROTEC
17、HNICAL COMMISSION _ MULTICORE AND SYMMETRICAL PAIR/QUAD CABLES FOR DIGITAL COMMUNICATIONS Part 10: Cables for cords with transmission characteristics up to 2 GHz Sectional specification FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization co
18、mprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International St
19、andards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this pr
20、eparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two orga
21、nizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form
22、 of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretat
23、ion by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or reg
24、ional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out
25、 by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees
26、 for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the
27、Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held r
28、esponsible for identifying any or all such patent rights. International Standard IEC 61156-10 has been prepared by subcommittee 46C: Wires and symmetric cables, of IEC technical committee 46: Cables, wires, waveguides, RF connectors, RF and microwave passive components and accessories. The text of t
29、his standard is based on the following documents: FDIS Report on voting 46C/1038/FDIS 46C/1042/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Dire
30、ctives, Part 2. BS IEC 61156-10:2016IEC 61156-10:2016 IEC 2016 5 A list of all parts in the IEC 61156 series, published under the general title Multicore and symmetrical pair/quad cables for digital communications, can be found on the IEC website. The committee has decided that the contents of this
31、publication will remain unchanged until the stability date indicated on the IEC website under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. A bilingual version of this
32、publication may be issued at a later date. BS IEC 61156-10:2016 6 IEC 61156-10:2016 IEC 2016 MULTICORE AND SYMMETRICAL PAIR/QUAD CABLES FOR DIGITAL COMMUNICATIONS Part 10: Cables for cords with transmission characteristics up to 2 GHz Sectional specification 1 Scope This part of IEC 61156 describes
33、cables primarily intended for work area cords as defined in ISO/IEC 11801 and in ISO/IEC TR 11801-9901 which is planned to be included in the next edition of ISO/IEC 11801-1. It covers overall screened cables with screened (X/FTP) or unscreened (X/UTP) pairs, where X stands for F, S or SF, as well a
34、s pair-screened cables without overall screen (U/FTP). The transmission characteristics of these cables are specified up to a frequency of 2 000 MHz and at a temperature of 20 C. Two categories of cables are recognised: Category 8.1 for use in Class I according to ISO/IEC TR 11801-9901; Category 8.2
35、 for use in Class II according to ISO/IEC TR 11801-9901. These cables can be used for various communication channels which use as many as four pairs simultaneously. The cables covered by this International Standard are intended to operate with voltages and currents normally encountered in communicat
36、ion systems. While these cables are not intended to be used in conjunction with low impedance sources, e.g. the electric power supplies of public utility mains, they are intended to be used to support the delivery of low voltage remote powering applications such as IEEE 802.3af (Power over Ethernet)
37、 or further developments e.g. according to IEEE 802.3at or IEEE 802.3bt. More information on the capacity to support these applications according to the installation practices are given in IEC PAS 61156-1-4, IEC TR 61156-1-6 and ISO/IEC TR 29125. 2 Normative references The following documents, in wh
38、ole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 61156-1:2007, Multicore and symme
39、trical pair/quad cables for digital communications Part 1: Generic specification IEC 61156-1:2007/AMD 1:2009 IEC TR 61156-1-2, Multicore and symmetrical pair/quad cables for digital communications Part 1-2: Electrical transmission characteristics and test methods of symmetrical pair/quad cables IEC
40、TR 61156-1-5, Multicore and symmetrical pair/quad cables for digital communications Part 1-5: Correction procedures for the measurement results of return loss and input impedance BS IEC 61156-10:2016IEC 61156-10:2016 IEC 2016 7 IEC TR 61156-1-6, Multicore and symmetrical pair/quad cables for digital
41、 communications Part 1-6: Exploratory DC-resistance values of floor-wiring and work-area cables for digital communications1IEC 61156-6:2010, Multicore and symmetrical pair/quad cables for digital communications Part 6: Symmetrical pair/quad cables with transmission characteristics up to 1 000 MHz Wo
42、rk area wiring Sectional specification IEC 62153-4-5, Metallic communication cables test methods Part 4-5: Electromagnetic compatibility (EMC) Coupling or screening attenuation Absorbing clamp method IEC 62153-4-9, Metallic communication cable test methods Part 4-9: Electromagnetic compatibility (EM
43、C) Coupling attenuation of screened balanced cables, triaxial method 3 Terms and definitions For the purposes of this document, the terms and definitions defined in IEC 61156-1 apply. 4 Installation considerations For the purposes of this document, the respective requirements of IEC 61156-6 apply. 5
44、 Materials and cable construction For the purposes of this document, the respective requirements of IEC 61156-6 apply. 6 Characteristics and requirements 6.1 General remarks Clause 6 lists the characteristics and minimum requirements of a cable complying with this standard. Test methods shall be in
45、accordance with Clause 6 of IEC 61156-1:2007/AMD 1:2009, except that the length of the cable under test shall be as specified below. In addition to all requirements specified in this Clause 6, the two categories shall meet all requirements specified for the respective categories in IEC 61156-6: Cate
46、gory 8.1: Category 6A; Category 8.2: Category 7A. NOTE By these requirements it is assured that Category 8.1 is backward compatible to Category 6Aand Category 8.2 is backward compatible to Category 7A. The computed requirements in dB, rounded to one decimal place, shall be used to determine complian
47、ce. The tests for electrical characteristics according to 6.2 shall be carried out on a cable length of not less than 100 m, unless otherwise specified. _ 1Under consideration. BS IEC 61156-10:2016 8 IEC 61156-10:2016 IEC 2016 The tests for transmission characteristics according to 6.3 shall be carr
48、ied out on a cable length of 30 m, unless otherwise specified. The following parameters are proportional to length and therefore the requirements for 30 m can be calculated from the requirements per 100 m by multiplying by 0,3: phase delay and differential delay; attenuation. 6.2 Electrical characte
49、ristics and tests 6.2.1 Conductor resistance The maximum conductor resistance at or corrected to 20 C shall not exceed 14,2 for 100 m of cable. 6.2.2 Resistance unbalance 6.2.2.1 Resistance unbalance within a pair The resistance unbalance shall not exceed 2,0 %. 6.2.2.2 Resistance unbalance between pairs The pair-to-pair resistance unbalance shall not exceed 5,0 %. 6.2.3 Dielectric strength The respective requirement of IEC 61156-6 applie
