1、BRITISH STANDARD BS EN 169101:1995 Specification for Harmonized system of quality assessment forelectronic components Blankdetail specification Quartzcrystal controlled oscillators (capability approval) The European Standard EN169101:1993 has the status of a British StandardBSEN169101:1995 BSI 03-20
2、00 ISBN 0 580 34575 0 Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee EPL/49, Piezo-electric devices for frequency control and selection, upon which the following bodies were represented: Federation of the Electronics Ind
3、ustry Institute of Physics Institution of Electrical Engineers Ministry of Defence National Supervising Inspectorate (BSI QA) Amendments issued since publication Amd. No. Date CommentsBSEN169101:1995 BSI 03-2000 i Contents Page Committees responsible Inside front cover National foreword ii Foreword
4、2 Text of EN169101 5BSEN169101:1995 ii BSI 03-2000 National foreword This British Standard has been prepared under the direction of the Electrotechnical Sector Board, and is the English language version ofEN169101:1993 Blank detail specification: Quartz crystal controlled oscillator (Capability Appr
5、oval), published by the European Committee for Electrotechnical Standardization (CENELEC) Electronic Components Committee (CECC). The text of this standard consists of the text ofEN169101:1993. The standard lists the ratings, characteristics and inspection requirements which shall be included as man
6、datory requirements in any detail specification for quartz crystal controlled oscillators which are to be assessed under capability approval procedures. Detail specifications shall conform to the requirements of this Blank detail specification and BSCECC00111: Rule of Procedure11. Specifications Par
7、t4:1994 Regulations for CECC Detail specifications. The British Standard which implements the CECC Rules of Procedure is BS9000 General requirements for a system for electronic components of assessed quality Part 2:1991 Specification for the national implementation of the CECC system. A British Stan
8、dard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-references Publications referred to Corresponding
9、 British Standard EN 169000:1992 BSEN169000:1993 Harmonized system of quality assessment for electronic components. Generic Specification. Quartz crystal controlled oscillators EN 169100:1993 BSEN169100:1994 Harmonized system of quality assessment for electronic components. Generic Specification. Qu
10、artz crystal controlled oscillators (capability approval) Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, theEN title page, pages2to9 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will
11、 be indicated in the amendment table on the inside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 169101 February 1993 UDC Descriptors: Quality, electronic components, oscillators English version Blank Detail Specification: Quartz Crystal Controlled Oscillators (Capability Approval
12、) Spcification Particulire Cadre: Oscillateurspilots par quartz (Agrmentdesavoir-faire) Vordruck fr Bauartspezifikationen: Quarzoszillatoren (Befhigungsanerkennung) This European Standard was approved by the CENELEC Electronic Components Committee(CECC) on31August1992. CENELEC members are bound to c
13、omply with CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the General Secr
14、etariat of the CECC or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CECC General Secretariat has th
15、e same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, and United Kingdom. The membership of t
16、he CECC is identical, with the exception of the national electrotechnical committees of Greece, Iceland and Luxembourg. CECC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: r
17、ue de Stassart 35, B-1050 Brussels 1993 Copyright reserved to CENELEC members Ref. No. EN 169101:1993EEN169101:1993 BSI 03-2000 2 Foreword The CENELEC Electronic Components Committee (CECC) is composed of those member countries of the European Committee for Electrotechnical Standardization (CENELEC)
18、 who wish to take part in a harmonized System for electronic components of assessed quality. The object of the System is to facilitate international trade by the harmonization of the specifications and quality assessment procedures for electronic components, and by the grant of an internationally re
19、cognized Mark, or Certificate, of Conformity. The components produced under the System are thereby acceptable in all member countries without further testing. This European Standard was prepared by CECCWG17, “Piezoelectric devices for frequency control and selection”. The text of the draft based on
20、documents CECC (Secretariat)2901 to2904/10.91 was submitted to the formal vote together with the voting reports, circulated as documents CECC(Secretariat)3107,3108,3109,3110/04.92 and3107A,3108A,3109A,3110A/07.92. The text was approved by CECC asEN169101:1993 on31August1992. The following dates were
21、 fixed: Contents Page Foreword 2 1 Ratings 5 2 Characteristics 5 3 Related documents 5 4 Marking 6 5 Ordering information 6 6 Certified test records 6 7 Additional information 6 8 Inspection requirements 6 Annex A Example front page layout forcustomerdetail specifications not for publication 9 Annex
22、 B Ageing test 9 Table 1 7 latest date of announcement of the ENat national level (doa) 1993-06-17 latest date of publication of an identical national standard (dop) 1993-12-17 latest date of declaration of national standards obsolescence 1993-12-17 latest date of withdrawal of conflicting national
23、standards (dow) 2003-06-17EN169101:1993 BSI 03-2000 3 Blank detail specification A blank detail specification is a supplementary document to the sectional specification and contains requirements for the minimum content of detail specifications. The front page layout shown on page4 is applicable to d
24、etail specifications for standard catalogue items only. For custom-built quartz crystal controlled oscillators where the detail specification is not intended for publication, a suggested layout for the front page is given inAnnex A. This is not mandatory, but it is recommended that the layout should
25、 be followed whenever possible. Identification of the detail specification and of the component The numbers between the square brackets on page4 correspond to the following information which should be given in the appropriate boxes. 1 The name of the National Standards Organization under whose autho
26、rity the detail specification is published and, if applicable, the organization from whom the detail specification is available. 2 The CECC Symbol and the number allotted to the detail specification by the CECC General Secretariat. 3 The number and issue number of the CECC generic or sectional speci
27、fication as relevant; also national reference if different. 4 If different from the CECC number, the national number of the detail specification, date of issue and any further information required by the national system, together with any amendment numbers. 5 A brief description of the quartz crysta
28、l controlled oscillator. (For example, SPXO and output frequency). 6 Information on typical construction (where applicable). (For example resistance welded, cold welded). For5 and6 the text to be given in the detail specification should be suitable for an entry inCECC00200 and CECC00300. 7 An outlin
29、e drawing with main dimensions which are of importance for interchangeability and/or reference to the appropriate national or international document for outlines. Alternatively, this drawing may be given in an annex to the detail specification.EN169101:1993 4 BSI 03-2000 Specification available from
30、: 1 EN69101-XXX 2 Page1 of. ELECTRONIC COMPONENTS OF ASSESSED QUALITY BY CAPABILITY APPROVAL INACCORDANCE WITH: 3 4 Outline and dimensions (firstangleprojection): 7 TYPE OF OSCILLATOR 5 ENCLOSURE 6 Dimensions inmmEN169101:1993 BSI 03-2000 5 1 Ratings (see 2.4 of EN169000 for preferred ratings) Opera
31、ting temperature range Climatic category Mechanical test severities 2 Characteristics (see 2.3 of EN169000) Nominal output frequency/range Reference temperature Frequency tolerance(s) Input conditions (as applicable) Output conditions (as applicable) Ageing The following characteristics shall be sta
32、ted as applicable: Control voltage Pulling sensitivity Linearity Modulation details Oven supply Stabilization time Retrace In addition other characteristics may be stated. NOTEInformation on the above characteristics may be given in tabular form. 3 Related documents Information about manufacturers w
33、ho have components qualified to this detail specification is available in the current CECC00200. Voltage : Current : Power : Voltage : Power : Waveform : Load : Voltage : Current : or Power : Generic specification EN169000 Sectional specification EN169100EN169101:1993 6 BSI 03-2000 4 Marking The mar
34、king of the quartz crystal controlled oscillator and the primary package shall be in accordance with the requirements of2.5 ofEN169000. Full details shall be given in the detail specification. 5 Ordering information The following ordering information shall be specified: 1) Quantity 2) CECC or custom
35、er detail specification number, issue number and date and where applicable 3) Nominal frequency expressed inkHz orMHz 4) Product code 5) Frequency tolerance(s) and operating temperature range 6) Full description of any additional requirements. 6 Certified test records The detail specification shall
36、state whether certified test records are required/not required in accordance with3.12 of EN169000. 7 Additional information (not for inspection purposes) The detail specification may include information (which is not normally required to be verified by the inspection procedure) such as circuit diagr
37、ams, curves, drawings and notes for the clarification of the detail specification. 8 Inspection requirements Clause numbers of tests and performance requirements refer to EN169000 The ILs and AQLs given inTable 1 are the minimum quality levels required and are selected fromIEC410 In this table The m
38、anufacturer and his customer shall ensure that any quality aspects of the quartz crystal controlled oscillator to be supplied that are not covered by the maintenance of the capability approval programme are included in the detail specification. This blank detail specification does not include any pe
39、riodic tests as these are controlled by the CQC testing under the maintenance of the capability approval as defined in3.11 and3.12 ofEN169100. D = destructive ND = non-destructive IL = inspection level AQL = acceptable quality levelEN169101:1993 BSI 03-2000 7 Table 1 Clause number and test D or ND C
40、onditions of test IL AQL% Performance requirements 100% INSPECTION ND 4.3.1 Visual testA 4.3.1 4.3.1 4.5.4 Output Frequency at reference temperature 4.5.4 Frequency tolerance(s) including offset frequencywhere applicable or 4.5.5(1) Frequency at specified temperatures 4.5.5(1) Frequency tolerance(s)
41、 4.5.11 Frequency adjustment (where applicable) 4.5.11 Minimum or minimum and maximum frequency change or 4.5.23 Frequency modulation characteristics Test(1) to(5) as applicable 4.5.23 Test(1) to(5) as applicable as4.5.23 GROUP A INSPECTION To be conducted on a sampling basis, lot-by-lot Sub-Group A
42、1 ND II 1,5 4.5.13 or 4.5.14 Oscillator output voltage 4.5.13 or 4.5.14 Limits as specified 4.5.15 or 4.5.16 Oscillator output waveform 4.5.15 or 4.5.16 Waveform as specified 4.5.3(1) Oscillator inputpower 4.5.3(1) Maximum power orcurrent andEN169101:1993 8 BSI 03-2000 Table 1 Clause number and test
43、 D or ND Conditions of test IL AQL% Performance requirements 4.5.3(3) Oven input power (where applicable) 4.5.3(3) Maximum power atswitch on Maximum power after stabilization or 4.5.3(2) Oven and Oscillator inputpower (where applicable) 4.5.3(2) Maximum power atswitch on Maximum power after stabiliz
44、ation Sub-Group A2 ND I 1,5 4.5.5(1) Frequency at specified temperatures (ifnot tested100%) 4.5.5(1) Frequency tolerance(s) Sub-Group A3 ND I 1,5 Ageing (when applicable) UseAnnex B to thisspecification Slope to be specified NOTEIt may be necessary to conduct this test100%. Group B Inspection To be
45、conducted on a sampling basis, lot-by-lot Sub-Group B1 ND S4 4,0 4.4.1 Dimensions TestA 4.4.1 4.4.1 Sub-Group B2 ND S4 4,0 For hermetically sealed devices only 4.6.2(2) Fine leak test 4.6.2(2) 2.4.5 4.6.2(1) Gross leak test 4.6.2(1) 4.6.2(1)EN169101:1993 BSI 03-2000 9 Annex A Example front page layo
46、ut for customer detail specifications not forpublication 1 Ratings (see 2.4 of EN169000 for preferred ratings) Operating temperature range Climatic category Mechanical test severities Annex B Ageing test The general conditions of test shall be as4.7.1 ofEN 169000 except that the duration shall be a
47、period sufficient to achieve the specified slope of frequency against time curve over a period of five days with a minimum duration of15days. Customer : Specification reference Issue Number Manufacturer : Date Page 1 of ELECTRONIC COMPONENTS OF ASSESSED QUALITY BY CAPABILITY APPROVAL INACCORDANCE WI
48、TH: 3 Manufacturers typenumber Outline and dimensions (first angle projection): 7 TYPE OF OSCILLATOR 5 ENCLOSURE 6 Dimensions in mmBS EN 169101:1995 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards
49、. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technic
