1、Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 09/07/2008 02:55, Uncontrolled Copy, (c) BSIg49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58a
2、nd door height windows Part 7: Finger catchesICS 91.190Building hardware Requirements and test methods for windows BRITISH STANDARDBS EN 13126-7:2007BS EN 13126-7:2007Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 09/07/2008 02:55, Uncontrolled Copy, (c) BSIThis British Standard was publishe
3、d under the authority of the Standards Policy and Strategy Committee on 31 March 2008 BSI 2008ISBN 978 0 580 58189 2Amendments/corrigenda issued since publicationDate Commentscontract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from le
4、gal obligations. National forewordThis British Standard is the UK implementation of EN 13126-7:2007. It supersedes DD CEN/TS 13126-7:2004 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee B/538, Doors, windows, shutters, hardware and curtain walling.A li
5、st of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 13126-7October 2007ICS 91.190 Supersedes CEN/TS 13126-7:2004 English VersionB
6、uilding hardware - Requirements and test methods for windowsand door height windows - Part 7: Finger catchesQuincaillerie pour le btiment - Exigences et methodesdessai des ferrures de fentres et portes-fentres - Partie7: Verrous de ferme-imposteBaubeschlge - Anforderungen und Prfverfahren frFenster
7、und Fenstertren - Teil 7: Fallen-SchnpperThis European Standard was approved by CEN on 23 August 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up
8、-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunde
9、r the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hun
10、gary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: r
11、ue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13126-7:2007: ELicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 09/07/2008 02:55, Uncontrolled Copy, (c) BSIEN 13126-7:2007 (E) 2 Contents
12、Page Foreword3 1 Scope.5 2 Normative references 5 3 Terms and definitions5 4 Classification5 4.1 General5 4.2 Category of use (1 first digit) .5 4.3 Durability (2 second digit)5 4.4 Mass (3 third digit) 5 4.5 Fire resistance (4 fourth digit) .5 4.6 Safety in use (5 fifth digit) 5 4.7 Corrosion resis
13、tance (6 sixth digit).6 4.8 Security (7 seventh digit) .6 4.9 Application (8 eighth digit).6 4.10 Test sizes Size limitations (9 ninth digit).6 4.11 Example of classification for finger catches.6 5 Requirements .6 5.1 General6 5.2 Additional tests 7 5.2.1 Mechanical resistance.7 5.2.2 Durability.7 6
14、 Test equipment.7 7 Test methods7 7.1 Samples 7 7.2 Durability test .8 7.3 Static load test8 7.4 Corrosion resistance .8 Annex A (informative) Test assembly9 Annex B (normative) Flowchart of test procedure.10 Bibliography 11 BS EN 13126-7:2007Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 09
15、/07/2008 02:55, Uncontrolled Copy, (c) BSIEN 13126-7:2007 (E) 3 Foreword This document (EN 13126-7:2007) has been prepared by Technical Committee CEN/TC 33 “Doors, windows, shutters, building hardware and curtain walling”, the secretariat of which is held by AFNOR. This document supersedes CEN/TS 13
16、126-7:2004. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2008, and conflicting national standards shall be withdrawn at the latest by April 2008. EN 13126 Building hardware - Requirements
17、 and test methods for windows and doors height windows consists of the following parts: Part 1: Requirements common to all types of hardware Part 2: Casement fastener handles1)Part 3: Manoeuvring fittings for espagnolette bolts/sliding button1)Part 4: Espagnolette bolts1)Part 5: Specification for de
18、vices that restrict the opening of windows Part 6: Variable geometry stay hinges (with or without a friction system)1)Part 7: Finger catches Part 8: Tilt sample B corrosion tests; sample C retained for reference control. NOTE 1 Sample B should only be necessary if no test report can be supplied by t
19、he manufacturer regarding the testing of the hardware component or set in accordance with EN 1670. NOTE 2 Sample C should be retained by the test institute for the duration of the validity of the test report. BS EN 13126-7:2007Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 09/07/2008 02:55,
20、Uncontrolled Copy, (c) BSIEN 13126-7:2007 (E) 8 7.2 Durability test Before the durability test measure the force F1necessary to operate the finger catch whilst maintaining a force F340 N 1 N at the centre of the top rail of the casement or sash (see Table 1 and Annex A, Figure A.1). Reduce force F3
21、by 20 N 1 N (see Table 1) at the centre of the top rail of the casement or sash and maintain throughout the test. Operate the casement or sash, without shock, for 10 000 cycles (+1 %) cycles at a rate of 250 cycles /h 250+cycles / h. After the test, measure and record the force F1required to operate
22、 the finger catch, while maintaining a force F3= 40 N 1 N, at the centre of the top rail of the casement or sash (see Table 1 and Annex A, Figure A.1). Hardware shall be lubricated in accordance with the manufacturers installation and maintenance instructions unless the hardware is claimed to be mai
23、ntenance-free. 7.3 Static load test (See Table 1) Apply static load F2= 200100+N for 60100+s and release (see Annex A, Figure A.1). After the static load test with F2 the hardware shall function correctly. Apply load F3= 300150+N for 60100+s. After the static load test with F3 the hardware shall fun
24、ction correctly. 7.4 Corrosion resistance NOTE This test is necessary if the manufacturer cannot provide a test report in accordance with EN 1670. All corrosion tests shall be on original new samples. Any frangible positioning lugs holding components together (i.e. for cam centre-positioning) shall
25、be broken. BS EN 13126-7:2007Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 09/07/2008 02:55, Uncontrolled Copy, (c) BSIEN 13126-7:2007 (E) 9 Annex A (informative) Test assembly 12F3F1F23Key 1 strike plate / keep 2 finger catch 3 section through specimen (showing dotted, part of simulated fr
26、ame and window casement or sash and direction of forces applied during tests) Figure A.1 Mounting of finger operated catch BS EN 13126-7:2007Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 09/07/2008 02:55, Uncontrolled Copy, (c) BSIEN 13126-7:2007 (E) 10 Annex B (normative) Flowchart of test
27、 procedure STARTFINISHSample BSample A Sample C7.4 Corrosion resistance7.2 Durability test Retained for reference control7.3 Static load testFigure B.1 Flowchart of test procedure BS EN 13126-7:2007Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 09/07/2008 02:55, Uncontrolled Copy, (c) BSIEN
28、13126-7:2007 (E) 11 Bibliography 1 EN 1670, Building hardware Corrosion resistance Requirements and test methods BS EN 13126-7:2007Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 09/07/2008 02:55, Uncontrolled Copy, (c) BSIBS EN BSILicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 09/07/
29、2008 02:55, Uncontrolled Copy, (c) BSI389 Chiswick High RoadLondonW4 4AL13126-7:2007BSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by
30、Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an
31、inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS
32、which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are al
33、so available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information
34、 on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (
35、0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 70
36、01. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in
37、 the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise witho
38、ut prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.
