1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58low carbon and high yield strength steel flat products for cold forming Tolerances on dimensions an
2、d shapeThe European Standard EN 10131:2006 has the status of a British StandardICS 77.140.50Cold rolled uncoated and zinc or zinc-nickel electrolytically coated BRITISH STANDARDBS EN10131:2006BS EN 10131:2006This British Standard was published under the authority of the Standards Policy and Strategy
3、 Committee on 31 July 2006 BSI 2006ISBN 0 580 48668 0Cross-referencesThe British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the
4、“Search” facility of the BSI Electronic Catalogue or of British Standards Online.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from lega
5、l obligations.Summary of pagesThis document comprises a front cover, an inside front cover, the EN title page, pages 2 to 12, an inside back cover and a back cover.The BSI copyright notice displayed in this document indicates when the document was last issued.Amendments issued since publicationAmd.
6、No. Date CommentsA list of organizations represented on this committee can be obtained on request to its secretary. present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep UK interests informed; monitor related international
7、and European developments and promulgate them in the UK.National forewordThis British Standard is the official English language version of EN 10131:2006. It supersedes BS EN 10131:1991 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee ISE/10, Flat rolle
8、d steels products, which has the responsibility to: aid enquirers to understand the text;EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 10131July 2006ICS 77.140.50 Supersedes EN 10131:1991 English VersionCold rolled uncoated and zinc or zinc-nickel electrolyticallycoated low carbon and high yield
9、 strength steel flat products forcold forming - Tolerances on dimensions and shapeProduits plats lamins froid, non revtus ou revtus dezinc ou de zinc-nickel par voie lectrolytique, en acier bascarbone et en acier haute limite dlasticit pour formage froid - Tolrances sur les dimensions et sur la form
10、eKaltgewalzte Flacherzeugnisse ohne berzug und mitelektrolytischem Zink- oder Zink-Nickel-berzug ausweichen Sthlen sowie aus Sthlen mit hhererStreckgrenze zum Kaltumformen - Grenzabmae undFormtoleranzenThis European Standard was approved by CEN on 12 June 2006.CEN members are bound to comply with th
11、e CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or
12、to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.
13、CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Swit
14、zerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2006 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN
15、10131:2006: EEN 10131:2006 (E) 2 Contents Foreword3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 Designation 4 5 Condition of delivery .5 6 Tolerances on thickness.5 7 Tolerances on width 8 7.1 General8 7.2 Sheet and wide strip8 7.3 Slit wide strip of width less than 600 mm .8 8 T
16、olerances on length.9 9 Tolerances on flatness9 9.1 General9 9.2 Steel grades with specified minimum yield strength Re 1 200 to 1 500 1500 1 200 1 200 to 1 500 1 500 = 0,35 to 0,40 0,03 0,04 0,05 0,020 0,025 0,030 0,40 to 0,60 0,03 0,04 0,05 0,025 0,030 0,035 0,60 to 0,80 0,04 0,05 0,06 0,030 0,035
17、0,040 0,80 to 1,00 0,05 0,06 0,07 0,035 0,040 0,050 1,00 to 1,20 0,06 0,07 0,08 0,040 0,050 0,060 1,20 to 1,60 0,08 0,09 0,10 0,050 0,060 0,070 1,60 to 2,00 0,10 0,11 0,12 0,060 0,070 0,080 2,00 to 2,50 0,12 0,13 0,14 0,080 0,090 0,100 2,50 to 3,00 0,15 0,15 0,16 0,100 0,110 0,120 aThe thickness tol
18、erances in the region of cold rolled welds may be increased by a maximum of 50 % over a length of 10 metres. This increase is applicable to all thicknesses and, unless otherwise agreed at the time of order, to normal and special tolerances over or under. Table 2 Tolerances on thickness for steel gra
19、des with a specified minimum yield strength 260 MPa Re 1200 to 1500 1500 1 200 1 200 to 1 500 1 500 = 0,35 to 0,40 0,04 0,05 0,06 0,025 0,030 0,035 0,40 to 0,60 0,04 0,05 0,06 0,030 0,035 0,040 0,60 to 0,80 0,05 0,06 0,07 0,035 0,040 0,050 0,80 to 1,00 0,06 0,07 0,08 0,040 0,050 0,060 1,00 to 1,20 0
20、,07 0,08 0,10 0,050 0,060 0,070 1,20 to 1,60 0,09 0,11 0,12 0,060 0,070 0,080 1,60 to 2,00 0,12 0,13 0,14 0,070 0,080 0,100 2,00 to 2,50 0,14 0,15 0,16 0,100 0,110 0,120 2,50 to 3,00 0,17 0,18 0,18 0,120 0,130 0,140 aThe thickness tolerances in the region of cold rolled welds may be increased by a m
21、aximum of 50 % over a length of 10 metres. This increase is applicable to all thicknesses and, unless otherwise agreed at the time of order, to normal and special tolerances over or under. 1) 1 MPa = 1 N/mm2. EN 10131:2006 (E) 7 Table 3 Tolerances on thickness for steel grades with a specified minim
22、um yield strength 340 MPa Re 420 MPa1)Dimensions in millimetres Nominal thickness Normal tolerances a for a nominal width w Special tolerances (S) a for a nominal width w 1200b 1 200 to 1 500 1500 1200b 1 200 to 1 500 1 500 = 0,35 to 0,40 0,04 0,05 0,06 0,030 0,035 0,040 0,40 to 0,60 0,05 0,06 0,07
23、0,035 0,040 0,050 0,60 to 0,80 0,06 0,07 0,08 0,040 0,050 0,060 0,80 to 1,00 0,07 0,08 0,10 0,050 0,060 0,070 1,00 to 1,20 0,09 0,10 0,11 0,060 0,070 0,080 1,20 to 1,60 0,11 0,12 0,14 0,070 0,080 0,100 1,60 to 2,00 0,14 0,15 0,17 0,080 0,100 0,110 2,00 to 2,50 0,16 0,18 0,19 0,110 0,120 0,130 2,50 t
24、o 3,00 0,20 0,20 0,21 0,130 0,140 0,150 aThe thickness tolerances in the region of cold rolled welds may be increased by a maximum of 50 % over a length of 10 metres. This increase is applicable to all thicknesses and, unless otherwise agreed at the time of order, to normal and special tolerances ov
25、er or under. Table 4 Tolerances on thickness for steel grades with a specified minimum yield strength 420 MPa 1 200 to 1 500 1 500 1200 1 200 to 1 500 1 500 = 0,35 to 0,40 0,05 0,06 0,07 0,035 0,040 0,050 0,40 to 0,60 0,05 0,07 0,08 0,040 0,050 0,060 0,60 to 0,80 0,06 0,08 0,10 0,050 0,060 0,070 0,8
26、0 to 1,00 0,08 0,10 0,11 0,060 0,070 0,080 1,00 to 1,20 0,10 0,11 0,13 0,070 0,080 0,100 1,20 to 1,60 0,13 0,14 0,16 0,080 0,100 0,110 1,60 to 2,00 0,16 0,17 0,19 0,100 0,110 0,130 2,00 to 2,50 0,19 0,20 0,22 0,130 0,140 0,160 2,50 to 3,00 0,22 0,23 0,24 0,160 0,170 0,180 aThe thickness tolerances i
27、n the region of cold rolled welds may be increased by a maximum of 50 % over a length of 10 metres. This increase is applicable to all thicknesses and, unless otherwise agreed at the time of order, to normal and special tolerances over or under. 1) 1 MPa = 1 N/mm2. EN 10131:2006 (E) 8 7 Tolerances o
28、n width 7.1 General Width is measured perpendicularly to the longitudinal axis of the product. The tolerances on width of flat products in low carbon and high yield strength steels are given in 7.2 for sheet and wide strip and in 7.3 for slit wide strip of width less than 600 mm. 7.2 Sheet and wide
29、strip The tolerances on width of sheet and wide strip shall be as given in Table 5. Table 5 Tolerances on width of sheet and wide strip Dimensions in millimetres Nominal width Normal tolerances Special tolerances (S) w Under Over Under Over w 1200 0 + 4 0 + 2 1200 1500 0 + 6 0 + 3 7.3 Slit wide stri
30、p of width less than 600 mm The tolerances on width of slit wide strip of width less than 600 mm shall be as given in Table 6. Table 6 Tolerances on slit wide strip of width less than 600 mm Dimensions in millimetres Tolerance class Nominal thickness Nominal width t w 125 125 w 250 250 w 400 400 w 6
31、00 Under Over Under Over Under Over Under Over t 0,6 0 + 0,4 0 + 0,5 0 + 0,7 0 + 1,0 0,6 t 1,0 0 + 0,5 0 + 0,6 0 + 0,9 0 + 1,2 1 t 2 0 + 0,6 0 + 0,8 0 + 1,1 0 + 1,4 Normal 2 t 3 0 + 0,7 0 + 1,0 0 + 1,3 0 + 1,6 t 0,6 0 + 0,2 0 + 0,2 0 + 0,3 0 + 0,5 0,6 t 1,0 0 + 0,2 0 + 0,3 0 + 0,4 0 + 0,6 1,0 t 2,0
32、0 + 0,3 0 + 0,4 0 + 0,5 0 + 0,7 Special (S) 2,0 t 3,0 0 + 0,4 0 + 0,5 0 + 0,6 0 + 0,8 EN 10131:2006 (E) 9 8 Tolerances on length Length is measured along one of the long sides of the sheet or cut length. The tolerances on length shall be as given in Table 7 and apply to all products covered by this
33、standard. Table 7 Tolerances on length Dimensions in millimetres Nominal length Normal tolerances Special tolerances (S) Under Over Under Over 2000 0 6 0 3 2000 0 0,3 % of the length 0 0,15 % of the length 9 Tolerances on flatness 9.1 General The tolerance on flatness is the maximum permitted distan
34、ce between the sheet and the horizontal surface on which it is placed. The measurement of waviness is only made on sheet edges. The flatness tolerances apply only to sheet. If the sheet is ordered non-skin passed only the normal tolerances are applicable. Flatness tolerances closer than special tole
35、rances may be agreed at the time of the order. 9.2 Steel grades with specified minimum yield strength Re 260 MPa Flatness tolerances for these steel grades shall be as given in Table 8. When these steel grades are ordered with the special tolerances given in Table 8, in case of dispute it is necessa
36、ry to verify that the wave height of any edge wave of length over 200 mm is always less than: 1 % of its length for a nominal sheet width 1500 mm; 1,5 % of its length for a nominal sheet width = 1500 mm. If the length of an edge wave is less than 200 mm it is necessary to verify that its maximum hei
37、ght does not exceed 2 mm. EN 10131:2006 (E) 10 Table 8 Flatness tolerances for steel grades with a specified minimum yield strength Re 260 MPa Dimensions in millimetres Tolerance class Nominal width Nominal thickness w t 0,7 0,7 t 1,2 t 1,2 w 600 7 6 5 600 w 1200 10 8 7 1200 w 1500 12 10 8 Normal w
38、1500 17 15 13 w 600 4 3 2 600 w 1200 5 4 3 1200 w 1500 6 5 4 w 1500 8 7 6 Special (FS) w 1500 Height of edge wave of length over 200 mm must be less than 1 % of its length. w 1500 Height of edge wave of length over 200 mm must be less than 1,5 % of its length. For edge waves of length less than 200
39、mm, the maximum height must not exceed 2 mm. 9.3 Steel grades with specified minimum yield strength 260 MPa Re 340 MPa Flatness tolerances for these steel grades shall be as given in Table 9. Flatness tolerances for widths less than 600 mm shall to agreed at the time of the order. Table 9 Flatness t
40、olerances for high yield strength steel sheet with specified minimum yield strength 260 Re 340 MPa Dimensions in millimetres Tolerance class Nominal width Nominal thickness w t 0,7 0,7 t 1,2 t 1,2 600 w 1 200 13 10 8 Normal 1 200 w 1 500 15 13 11 w 1 500 20 19 17 600 w 1 200 8 6 5 Special (FS) 1200
41、w 1 500 9 8 6 w 1 500 12 10 9 EN 10131:2006 (E) 11 9.4 Steel grades with specified minimum yield strength Re 340 MPa For these steel grades, the values for flatness tolerances shall be specified at the time of the order. 10 Tolerances on out of squareness The out-of-squareness (u) is the orthogonal
42、projection of transverse edge over a longitudinal edge (see Figure 1). The out-of-squareness shall not exceed 1 % of the actual width of the sheet. 11 Tolerances on edge camber Edge camber (q) is the maximum distance between a longitudinal edge and a straight edge supported on the latter (see Figure
43、 1). Edge camber shall be measured on the concave edge. The basis of measurement shall be a distance of 2 m taken at any point on the edge. In the case of sheets and cut lengths with a length less than 2 m, the basis measurement shall be equal to their length. The edge camber shall not exceed 5 mm o
44、ver a length of 2 m. For lengths less than 2 metres, the edge camber shall not exceed 0,25 % of the actual length. For slit wide strip of width less than 600 mm a special edge camber tolerance (CS) of 2 mm maximum on a 2 m length may be specified. This special edge camber tolerance is not applicable
45、 to slit wide strip of high yield strength steels. 12 Superimposition of dimensions By agreement at the time of ordering, the tolerance on out-of-squareness and edge camber may be replaced by a requirement that a perfect rectangle formed by the ordered width and length dimensions can be superimposed
46、 onto the sheets delivered. Figure 1 Out-of-squareness (u) and edge camber (q) EN 10131:2006 (E) 12 Bibliography 1 EN 10130, Cold rolled low carbon steel flat products for cold forming Technical delivery conditions 2 EN 10152, Electrolytically zinc coated cold rolled steel flat products for cold for
47、ming Technical delivery conditions 3 EN 10209, Cold rolled low carbon steel flat products for vitreous enamelling Technical delivery conditions 4 EN 10268, Cold rolled steel flat products with higher yield strength for cold forming Technical delivery conditions 5 EN 10271, Electrolytically zinc-nickel (ZN) coated steel flat products Technical delivery conditions 6 prEN 10338, Cold rolled flat products of multiphase steels for cold forming Technical delivery conditions 7 prEN 10336, Continuously hot-dip coated and electrolytically coated s
