欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    BS 6043-4 6-1991 Methods of sampling and test for carbonaceous materials used in aluminium manufacture - Cold ramming pastes - Determination of maximum rammed apparent density of u.pdf

    • 资源ID:545618       资源大小:365.42KB        全文页数:10页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    BS 6043-4 6-1991 Methods of sampling and test for carbonaceous materials used in aluminium manufacture - Cold ramming pastes - Determination of maximum rammed apparent density of u.pdf

    1、BRITISH STANDARD BS 6043-4.6: 1991 Methods of sampling and test for Carbonaceous materials used inaluminium manufacture Part 4: Cold ramming pastes Section 4.6 Determination of maximum rammed apparent density of unbaked paste NOTEIt is recommended that this Section be read in conjunction with thegen

    2、eral information in BS6043-4.0, published separately.BS6043-4.6:1991 This British Standard, having been prepared under the directionof the Chemicals Standards Policy Committee, waspublished under the authorityof the Standards Boardand comes into effect on 30September1991 BSI 10-1999 The following BS

    3、I references relate to the work on this standard: Committee reference CIC/24 Draft for comment 90/54846 DC ISBN 0 580 19731 X Committees responsible for this British Standard The preparation of this British Standard was entrusted by the Chemicals Standards Policy Committee (CIC/-) to Technical Commi

    4、ttee CIC/24, upon which the following bodies were represented: Aluminium Federation British Ceramic Research Ltd. Chemical Industries Association Institute of Petroleum Refractories Association of Great Britain Amendments issued since publication Amd. No. Date CommentsBS6043-4.6:1991 BSI 10-1999 i C

    5、ontents Page Committees responsible Inside front cover Foreword ii 0 Introduction 1 1 Scope 1 2 Principle 1 3 Definition 1 4 Apparatus 1 5 Sampling 1 6 Preparation of test samples 1 7 Procedure 1 8 Calculation and expression of results 3 9 Test report 3 Figure 1 Sand rammer 2 Publication(s) referred

    6、 to Inside back coverBS6043-4.6:1991 ii BSI 10-1999 Foreword This Section of BS6043has been prepared under the direction of the Chemicals Standards Policy Committee to provide methods of test for cold ramming pastes used in the production of aluminium. There is no corresponding International Standar

    7、d; however, it is intended, upon publication of this Section of BS6043, that it be offered to the International Organization for Standardization (ISO) for possible adoption as an International Standard. It is essential to use BS6043-4.1in conjunction with this Section of BS6043. This standard descri

    8、bes a method of test only, and should not be used or quoted as a specification defining the characteristics of a product. Reference to this Section should indicate that the method of test used is in accordance with BS6043-4.6:1991. A British Standard does not purport to include all the necessary pro

    9、visions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages1to4, an

    10、inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.BS6043-4.6:1991 BSI 10-1999 1 0 Introduction As the apparent density of ramming materials asymptot

    11、ically approaches a maximum as ramming proceeds, it is necessary for practical purposes to limit the number of ramming strokes to that which gives an acceptably close approximation to the true maximum apparent density. 1 Scope This Section of BS6043describes a method for the determination of the max

    12、imum rammed apparent density (MRAD) achievable by ramming compaction for unbaked cold ramming pastes used in aluminium manufacture. NOTEThe titles of the publications referred to in this standard are listed on the inside back cover. 2 Principle The test sample, contained in a cylindrical mould, is s

    13、ubjected to a defined number of blows at a specified force and the achieved apparent density is calculated from the mass and dimensions of the resulting rammed test piece. 3 Definition For the purposes of this Section of BS6043,the definitions given BS6043-4.1apply, together with the following. test

    14、 piece a rigid body of fixed dimensions formed from a test sample of cold ramming paste by ramming compaction 4 Apparatus 4.1 Ordinary laboratory apparatus 4.2 Sand rammer 1) , as shown in Figure 1, or similar apparatus in which a sample contained in a mould may be subjected to a succession of impac

    15、ts transmitted by a6.35kg weight falling through a distance of50mm. The mould has an internal diameter of50mm. 4.3 Electric oven, capable of being controlled at35 2 C. 4.4 Vernier callipers, capable of measuring lengths of not less than150mm and a vernier scale graduated in0.1mm or smaller units. 5

    16、Sampling Prepare a representative laboratory sample of the cold ramming paste in accordance with BS6043-4.1. 6 Preparation of test samples Prepare at least three test samples each of mass170 0.1g from the laboratory sample (seeclause5) by the method described in5.5.3 of BS6043-4.1:1991. 7 Procedure

    17、7.1 Ramming the test sample Transfer a test sample to a loosely-lidded container of suitable volume. Place the container and the lightly lubricated sand rammer mould (4.2) in the electric oven (4.3) controlled at35 2 C for30min. Transfer the warmed test sample to the warmed mould and position the mo

    18、uld in the sand rammer. Subject the sample in the mould to50impacts by turning the sand rammer handle. Invert the mould in the sand rammer and lower the plunger gently into it to bring the partially completed test piece into contact with the base of the mould. Subject the test sample to a further50i

    19、mpacts. Remove the test piece from the mould and allow it to cool to room temperature. 7.2 Determination Weigh the test piece to the nearest0.1g. Using the vernier callipers (4.4), measure the height of the test piece at four points equidistant around the circumference, to the nearest0.1mm and take

    20、the mean of the four measurements, rounded to the nearest0.1mm. Make two pairs of measurements of the diameter of the test piece, each pair in directions mutually at right angles, one pair at points at one-third of the sample height and the second pair at points at two-thirds of the sample height. M

    21、easure to the nearest0.1mm and take the mean of the four readings, rounded to the nearest0.1mm. 7.3 Number of determinations Perform the operations described in7.1 and7.2 on each of three test samples. Reject any test piece which is not502mm in height and repeat the operations described in7.1 and7.2

    22、 on a new test sample (see clause6) ofmass modified in accordance with5.5.3 of BS6043-4.1:1991. 1) For information on the availability of this apparatus, write to Customer Information, BSI, Linford Wood, Milton Keynes, MK145LE.BS6043-4.6:1991 2 BSI 10-1999 NOTEEach turn of the handle causes the6.35k

    23、g weight to be raised50mm and then dropped on the collar attached to the plunger shaft. Figure 1 Sand rammerBS6043-4.6:1991 BSI 10-1999 3 8 Calculation and expression of results Calculate the apparent density, D, for each of the three compacted test pieces, expressed in g/mL, from the following equa

    24、tion: where: If the range of the three results is greater than0.01g/mL, reject the results and repeat the procedure described in clause7 using fresh test samples (see clause6). Calculate the mean of the three valid determinations, to obtain the MRAD, expressed to the nearest0.005g/mL. 9 Test report

    25、The test report shall include the following information: a) a complete identification of the sample; b) a reference to this British Standard, i.e.BS6043-4.6:1991; c) the mean value of the three measurements of the maximum rammed apparent density, calculated and expressed in accordance with clause8;

    26、d) any unusual features noted during the determination; e) any operation not included in this British Standard or regarded as optional. M is the mass of the test piece (see7.2) (in g); h is the mean height; of the test piece (see7.2) (in mm); d is the mean diameter of the test piece (see7.2) (in mm)

    27、. D 1000 M hd 2 () 2 - =4 blankBS6043-4.6:1991 BSI 10-1999 Publication(s) referred to BS 6043, Methods of sampling and test for carbonaceous materials used in aluminium manufacture. BS 6043-4, Cold ramming pastes. BS 6043-4.0, General introduction 2) . BS 6043-4.1, Methods of sampling. 2) Referred t

    28、o on the front cover only.BS 6043-4.6: 1991 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Ro

    29、yal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an i

    30、naccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that

    31、subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to

    32、 supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Vario

    33、us BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchas

    34、e price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as

    35、 permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the c

    36、ourse of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.


    注意事项

    本文(BS 6043-4 6-1991 Methods of sampling and test for carbonaceous materials used in aluminium manufacture - Cold ramming pastes - Determination of maximum rammed apparent density of u.pdf)为本站会员(jobexamine331)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开