欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    BS 3928-1969 Method for sodium flame test for air filters (other than for air supply to I C engines and compressors)《空气过滤器的钠焰试验方法(为内燃机和压缩机供气用的除外)》.pdf

    • 资源ID:543993       资源大小:2.39MB        全文页数:52页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    BS 3928-1969 Method for sodium flame test for air filters (other than for air supply to I C engines and compressors)《空气过滤器的钠焰试验方法(为内燃机和压缩机供气用的除外)》.pdf

    1、BRITISH STANDARD BS 3928:1969 Method for Sodium flame test for air filters (Other than for air supply to I.C. engines and compressors) UDC 621.928.9.001.4BS3928:1969 Tins British Standard, having been approved by the Mechanical Engineering Industry Standards Committee, was published under the author

    2、ity of the Executive Board on 29 August 1969 BSI 09-1999 First published September, 1965 First revision August, 1969 The following BSI references relate to the work on this standard: Committee references MEE/95 and MEE/95/3 Draft for comment 68/11604 ISBN 580 05740 2 Co-operating organizations The M

    3、echanical Engineering Industry Standards Committee, under whose supervision this British Standard was prepared, consists of representatives from the following Government departments and scientific and industrial organizations: Associated Offices Technical Committee Institute of Marine Engineers Asso

    4、ciation of Consulting Engineers Institution of Civil Engineers Association of Mining Electrical and Mechanical Institution of Gas Engineers Engineers Institution of Heating and Ventilating Board of Trade Engineers* British Chemical Plant Manufacturers Institution of Mechanical Engineers Association

    5、Institution of Mechanical Engineers British Compressed Air Society* (Automobile Division) British Electrical and Allied Manufacturers Institution of Production Engineers Association Locomotive and Allied Manufacturers British Gear Manufacturers Association Association of Great Britain British Intern

    6、al Combustion Engine London Transport Board* Manufacturers Association Machine Tool Trades Association British Mechanical Engineering Confederation Ministry of Defence British Pump Manufacturers Association Ministry of Defence, Army Department* British Steel Industry Ministry of Power Crown Agents f

    7、or Oversea Governments and Ministry of Public Building and Works* Administrations Ministry of Technology* Department of Employment and Productivity Ministry of Technology National (H.M. Factory Inspectorate)* Engineering Laboratory Electricity Council, the Central Electricity Ministry of Transport G

    8、enerating Board and the Area Boards in National Coal Board England and Wales National Physical Laboratory (Ministry of Engineering Equipment Users Association Technology) Gas Council Royal Institute of British Architects The Government departments and scientific and industrial organizations marked w

    9、ith an asterisk in the above list, together with the following, were directly represented on the committee entrusted with the preparation of this standard: Council of British Manufacturers of Petroleum Society of British Aerospace Companies Ltd Equipment Technical Section of the British Paper and Fa

    10、n Manufacturers Association Ltd Board Makers Association Ministry of Public Building between 200 ft 3 /min (340 m 3 /h) and 500 ft 3 /min (850 m 3 /h) 2 atomizers; between 50 ft 3 /min (85 m 3 /h) and 200 ft 3 /min (340 m 3 /h) 1 atomizer, and below 50 ft 3 /min (85 m 3 /h) preferably a one hole ato

    11、mizer. Each compressed air flowmeter shall be capable of measuring 3.3 ft 3 /min to 3.5 ft 3 /min (95 l/min to 100 l/min) of free air at a pressure of 100 lbf/in 2(7 bar 6) ). Alternatively, a single flowmeter capable of measuring the same total flow may be incorporated in the manifold (e.g.2 ft 3 /

    12、min to 20 ft 3 /min (50 l/min to 500 l/min) range flowmeter for 4 atomizers), together with an isolating valve on each feedpipe. The constant pressure of 100 lbf/in 2(7 bar 6) ) may be obtained by the use of either a bleed-off valve or a regulating valve in the manifold. The valve shall be mounted n

    13、ear the flame tube to facilitate operation of the rig, together with a pressure gauge and the flowmeter (ifa single one is used). The pressure gauge shall be of the Bourdon type with a dial of not less than6inches (150 mm) diameter, reading accurately to100 lbf/in 2(7 bar 6) ). 3.4 Ducting. The duct

    14、ing B shall be of such diameter, D, that the linear speed of air shall not exceed 30 ft/s (9 m/s) and of such length that at least 2 seconds shall elapse for the passage of air between the atomizers and the filter under test, so that complete evaporation of water from the spray takes place before ar

    15、rival at the filter. It shall be made of, or treated with, salt-resistant material such as polyvinyl chloride. A sump shall be provided on the underneath of the duct, placed at a distanceD from the spray box, to drain liquid carried over from the atomizers. The circular mixing baffle of diameter sit

    16、uated at least 10 D from the spray box shall be supported centrally on wires or thin strips offering little resistance to flow. One axial sampling point E facing up-stream, at least5D from the baffle shall be provided in the inlet ducting, near the front face of the filter unit, for calibration purp

    17、oses and r.h. measurements of the salt-laden air. The sampling orifice E shall have a sharp leading edge, and be of such a diameter that the sampling velocity is between ! and 4 times the duct velocity at a sampling flow rate of between1ft 3 /min and 2 ft 3 /min (28 l/min and56 l/min). Within these

    18、limits, errors due to anisokinetic sampling are negligible. For a test rig handling 1000 ft 3 /min (1700 m 3 /h) ducting diameter D of 12 in (305mm) is suitable. 3.5 The filter housing. This shall consist of expanding sections from circular inlet to rectangular section, the cross-sectional area of t

    19、he large end being not more than 50 % greater than that of the filter under test. Between the expanding sections there shall be a parallel section, of the same cross section as the rectangular ends, having a length between 10 % and 20 % greater than the depth of the filter under test, and within whi

    20、ch the complete filter unit (including support and retaining frame) is to be mounted on a suitable supporting plate in accordance with the filter manufacturers normal method of installation. Static pressure taps shall be provided as near as practicable to the front and back faces of the filter. A su

    21、itable differential manometer capable of being read to an accuracy of 0.05 in (0.1mm) water gauge (w.g.) shall be connected to the pressure taps. NOTEWhen the maximum face dimension of the filter exceeds say,3ft (915mm) the expander section on the upstream side becomes inconveniently long. Shorter expanders (but not less than1;X ) may be used if it is demonstrated that the dust distribution remains uniform over the face of the filter. 5) 1 bar = 10 5N/m 2 . 6) 1 bar = 10 5N/m 2 . D/2


    注意事项

    本文(BS 3928-1969 Method for sodium flame test for air filters (other than for air supply to I C engines and compressors)《空气过滤器的钠焰试验方法(为内燃机和压缩机供气用的除外)》.pdf)为本站会员(赵齐羽)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开