欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM F2467-2006 Standard Practice for Measuring Static Sealing Pressure Using Pressure-Indicating Film (PIF) in Transportation Applications《运输用途中用压力指片(PIF)测量静态密封压力的标准实施规程》.pdf

    • 资源ID:538786       资源大小:51.74KB        全文页数:2页
    • 资源格式: PDF        下载积分:5000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要5000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM F2467-2006 Standard Practice for Measuring Static Sealing Pressure Using Pressure-Indicating Film (PIF) in Transportation Applications《运输用途中用压力指片(PIF)测量静态密封压力的标准实施规程》.pdf

    1、Designation: F 2467 06Standard Practice forMeasuring Static Sealing Pressure Using Pressure-Indicating Film (PIF) in Transportation Applications1This standard is issued under the fixed designation F 2467; the number immediately following the designation indicates the year oforiginal adoption or, in

    2、the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice covers a standard means for measuringinitial static sealing pressure

    3、in transportation applications.1.2 It uses a pressure-indicating film (PIF) that will recordthe maximum load imprint of the seal-to-flange interfaces. Theimprints will vary in intensity based on load across and alongthe interface.1.3 These imprints can be used to determine if initial loadon the gask

    4、et is adequate to attain a seal. These imprints mayalso indicate correct bolt torque sequence. These imprints mayalso be used to determine if the mating surface waviness orlocal flatness meets gasket requirements. Roughness is rarelyfound by PIFs because peak-to-peak wavelengths are too short.PIF is

    5、 very good at finding waviness (peak to peak 2.5 mm)and local flatness dips. PIFs provide an approximation ofmaximum pressures, and do not take into account relaxation ofthe joint after the torque sequence. Other methods involvingdynamic measurement should be used if flange loading afterrelaxation i

    6、s desired.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Te

    7、rminology2.1 Definitions:2.1.1 pressure-indicating film (PIF), nfilm that will, undervarying clamp forces, give a varying imprint or color densitythat correlates directly with the joint clamp force applied in agiven area.3. Special Test Equipment and Materials3.1 Pressure-indicating film (PIF) in th

    8、e required pressurerange(s).3.2 A bolt micrometer or torque wrench for quantifyingfastener load or sequence or both. For yielded fastener appli-cations, torque versus yield or angle recording equipment isalso required.3.3 Subassembly test stand with one set of mating parts ofthe joint (minimum) and

    9、a complete set of fasteners. A new setof fasteners for each run shall be used if the torque loading ishigh enough to cause plastic deformation of the bolts.3.4 A sufficient quantity of gaskets to complete the requirednumber of tests as agreed upon between producer and user.Reuse of gaskets after ini

    10、tial tightening is not allowed, unlessapproved by the user.3.5 Manual densitometer or automatic scanning device forreading color density (optional).4. Summary of Practice4.1 PIF is placed between a gasket or seal and one or bothof the mating flanges. Using the specified torque sequence, theassembly

    11、is clamped together. After the specified waitingperiod, the system is unclamped and the PIF removed. Thevisible color pattern denotes where clamp pressure is present.The approximate pressure can be determined from colordensity using a reflective (optical) densitometer or an auto-matic scanning devic

    12、e in conjunction with a computer conver-sion program designed for the films. Follow the PIF suppliersguidelines with regard to how color density relates to pressurefor a given PIF.5. Significance and Use5.1 This practice is a screening tool and should be used inconjunction with other more accurate r

    13、eal-time load-measuringtechniques.5.2 This practice covers the use of PIF, which is available inseveral load ranges. This practice also covers the use of amanual or automatic scanning device to read indicated load.5.3 Limitations include those applications in which the PIFmay be kinked, twisted, or

    14、buckled. PIF does not withstandelevated temperature, low temperature, or fluid aging and does1This practice is under the jurisdiction of ASTM Committee F03 on Gaskets andis the direct responsibility of Subcommittee F03.10 on Composite Gaskets.Current edition approved Oct. 1, 2006. Published October

    15、2006. Originallyapproved in 2005. Last previous edition approved in 2005 as F 2467 05.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.not take into account any relaxation of bolts, gasket materials,or flange twisting, as it provides

    16、only the maximum attainedpressure.6. Conditioning6.1 Conditioning of the assembly or gaskets before test isnot specified, but may be required, as agreed upon between theproducer and user. No special conditioning of the PIF isrequired.7. Sampling7.1 The number of engine parts and components to beeval

    17、uated using this practice shall be agreed upon betweenproducer and user.7.2 Mating flanges in the test area shall be examined fornicks or scratches that may affect test results. Componentsshall be repaired or replaced as required.8. Measurements8.1 Measurement of the color density of the pattern can

    18、 bedone with a manual or automatic scanning device, densitom-eter, using the PIF suppliers recommended guidelines. PIFmeasuring accuracy can, however, be adversely affected byaging of the pressure pattern by artificial or natural light (limitexposure of film containing the pressure pattern to lights

    19、ources, which can fade the resultant pressure pattern).9. Procedure9.1 Select the appropriate range of PIF. This may be donebased on prior experience or by trial and error. Most sealingapplications may start out using PIF in the low-pressureregions. Head or exhaust gasket joints typically use PIF in

    20、 themedium- to high-pressure regions. Consult the PIF supplierguidelines to determine the proper film type to use based onexpected load ranges. Head gasket coolant and oil sealing areaevaluation will typically use medium PIF, while combustionsealing area evaluation will typically use high PIF. One-p

    21、artPIF is preferred for head gasket system evaluations. It ispreferable to have the glossy side oriented toward the gasket. Ifa two-part PIF is used, the two portions of PIF should only bebrought together right before the test, and must be separatedquickly after the test to avoid continuing color de

    22、velopment,which can affect the result.9.2 Using properly sized film, punch holes to allow clear-ance for fasteners, dowels, and so forth.9.3 Properly clean parts to ensure they are free of fluids andother contaminants as this will affect color intensity.9.4 Shim as necessary to compensate for PIF in

    23、terferencewith joint clamp load. This is necessary only when the PIFtemplate does not cover the entire flange surface (user onlywants to measure a portion of a flange surface).9.5 Loosely assemble the joint with the PIF on one or bothsides of the joint.9.6 Begin tightening the bolts in the pattern s

    24、pecified for thejoint.9.7 Tighten bolts in at least three increments to attain thefinal specified torque. This is to be done to avoid artificiallyhigh readings as well as over compression of the paper androcking of the joint. Alternatively, production validation mayuse a multiple spindle to tighten

    25、bolts per the productionprocess conditions.9.8 Leave the joint assembled under final torque for theperiod of time recommended by the PIF supplier, usually 2 minminimum. Record the total exposure time under final torque.9.9 Disassemble the joint by carefully relieving the torquefrom the fasteners usi

    26、ng the reverse order of the initial torquesequence. Remove the PIF. Label the PIF with date of test, partlevel, test laboratory relative humidity and ambient tempera-ture, PIF type (ultra low, super low, low; medium; high), bolttorque, and any other pertinent information.9.10 Conduct visual inspecti

    27、on and measure color densityusing a densitometer following the PIF suppliers guidelinesaccordingly. Other automatic scanning devices may also beused as agreed upon between producer and user.9.11 Take color photographs of the PIFs (optional).9.12 To avoid fading of color density, store PIFs in a dark

    28、area, away from fluorescent or natural light.10. Report10.1 A report normally consists of just the PIF impressionsand pressure readings along with the information as agreedupon in 9.9 and 9.10.11. Keywords11.1 gasket; PIF; pressure; pressure-indicating filmASTM International takes no position respec

    29、ting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This sta

    30、ndard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM Internati

    31、onal Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below

    32、.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).F2467062


    注意事项

    本文(ASTM F2467-2006 Standard Practice for Measuring Static Sealing Pressure Using Pressure-Indicating Film (PIF) in Transportation Applications《运输用途中用压力指片(PIF)测量静态密封压力的标准实施规程》.pdf)为本站会员(Iclinic170)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开