欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM F1298-1990(2006) Standard Specification for Flexible Expansion-Type Ball Joints for Marine Applications《船用柔性扩展型球连接》.pdf

    • 资源ID:534593       资源大小:62.71KB        全文页数:3页
    • 资源格式: PDF        下载积分:5000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要5000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM F1298-1990(2006) Standard Specification for Flexible Expansion-Type Ball Joints for Marine Applications《船用柔性扩展型球连接》.pdf

    1、Designation: F 1298 90 (Reapproved 2006)An American National StandardStandard Specification forFlexible, Expansion-Type Ball Joints for MarineApplications1This standard is issued under the fixed designation F 1298; the number immediately following the designation indicates the year oforiginal adopti

    2、on or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers the design, manufacture, andtesting of ball joi

    3、nts utilized for accommodating thermalexpansion and contraction, or mechanical movement of apipeline carrying fluid. The ball joints are intended for use insystems operating above 0F (18C).1.2 The following precautionary caveat pertains only to thetest methods portion, Section 7, of this specificati

    4、on: Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.2. Referenced Docu

    5、ments2.1 ASTM Standards:2A 395/A 395M Specification for Ferritic Ductile IronPressure-Retaining Castings for Use at Elevated Tempera-turesF 722 Specification for Welded Joints for Shipboard PipingSystems2.2 ANSI Standard:B 31.1 Power Piping32.3 American Society of Mechanical Engineers:4ASME Boiler a

    6、nd Pressure Vessel Code, Section VIII,Division 1, Pressure Vessels Section IX, Welding andBrazing Requirements3. Ordering Information3.1 Each purchase order or inquiry for ball joints to thisspecification shall include the following as applicable:3.1.1 Title, number, and latest revision of this spec

    7、ification,3.1.2 Manufacturers part number or ball-joint type infor-mation,3.1.3 Materials for ball joint and seals, if other than to thisspecification,3.1.4 Service conditions,3.1.4.1 Minimum and maximum operating temperature(F),3.1.4.2 Maximum operating pressure (psig),3.1.5 Fluid media (internal),

    8、3.1.6 Atmosphere or media (external),3.1.7 ANSI pressure class, facing and drilling of flangedends, and pipe schedule or wall thickness of ends for weld endjoints,3.1.8 Special end connections as defined by the purchaser,3.1.9 Ball sphere or other special coatings, if required,3.1.10 Qualification t

    9、est report, if required,3.1.11 Drawing requirements; for example, envelope draw-ing sufficiently detailed to describe the ball joint to be supplied,and3.1.12 Other tests to satisfy customer requirements.4. Materials and Manufacture4.1 All pressure retaining components shall be fabricatedfrom wrought

    10、 or cast steel. Ductile iron complying withSpecification A 395 may be used for the ball joint retainingring in services not above 350 psig (2.41 N/mm2) or 450F(232C). Steel shall comply with one of the materials listed inSection VIII, Division 1, of the ASME Code, or ANSI B 31.1.4.2 Bolting material

    11、 shall be in accordance with ANSIB 31.1.4.3 Ball spheres shall be coated in accordance with themanufacturers standard practice or as specified by the custom-ers specification (see 3.1.9).4.4 Corrosion shall be considered in the design as set forthin UG-25 of the ASME Code, Section VIII, Division 1.1

    12、This specification is under the jurisdiction of ASTM Committee F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.11 onMachinery and Piping Systems.Current edition approved Feb. 1, 2006. Published February 2006. Originallyapproved in 1990. Last previous edition ap

    13、proved in 2001 as F 1298 90 (2001).2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from American N

    14、ational Standards Institute, 25 W. 43rd St., 4thFloor, New York, NY 10036.4Available from American Society of Mechanical Engineers (ASME), ASMEInternational Headquarters, Three Park Ave., New York, NY 10016-5990.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA

    15、 19428-2959, United States.4.5 Seals and packing material shall be suitable for theservice intended. This includes being adequate for the pressureand temperature rating and having sufficient resistance toattack by the fluid media and atmosphere specified in Section3.4.6 Welding procedure qualificati

    16、on, welder performancequalification, and welding materials shall be in accordancewith ANSI B 31.1 and Section IX of the ASME Code. Brazingor soldering shall not be used.5. Other Requirements5.1 Design:5.1.1 Ball joints shall be designed to conform to applicablesections of the latest edition of ANSI

    17、B 31.1.5.1.2 PackingThe design for containment of leakage shallbe of the manufacturers standard design and be qualified byprototype testing of 7.1.5.2 Pressure and Temperature Rating:5.2.1 The maximum allowable working pressure (MAWP)and temperature rating for ball joints conforming to thisspecifica

    18、tion shall be established by at least one of thefollowing methods:5.2.1.1 Proof test in accordance with the requirementsprescribed in paragraph UG-101 of Section VIII, Division 1, ofthe ASME Code. If burst type tests as outlined in paragraphUG-101(m) are used, it is not necessary to rupture thecompo

    19、nent. In this case, the value of B to be used indetermining the MAWP shall be the maximum pressure towhich the component was subjected without rupture. Compo-nents that have been subjected to a hydrostatic proof test shallnot be offered for sale.5.2.1.2 Design calculations in accordance with the req

    20、uire-ments prescribed in Section VIII, Division 1, of the ASMECode.5.3 Each ball joint bolting or retainer nut shall be adjustedfor proper torque.5.4 Where welded construction is used for the fabrication ofpressure containing parts, welded joint design details shall bein accordance with Section VIII

    21、, Division 1, of the ASMECode and Specification F 722. Except for fillet welds, all weldsshall be full penetration welds extending through the entirethickness of the shell.5.5 Inlet and outlet connections consisting of welded flangesand fittings shall be in accordance with Specification F 722.When r

    22、adiography is required (see 8.2), all welds shall be buttwelds for Class I piping as required by Specification F 722,except packing cylinders, drains, and similar ancillary connec-tions, which may be attached by fillet or socket welds.5.6 Threaded pipe connections shall be limited to thefollowing se

    23、rvices:3/4 in. (19 mm) NPS and under1500 psig (10.3 N/mm2) max1 in. (25 mm) NPS and under 1200 psig (8.27 N/mm2) max2 in. (50 mm) NPS and under 600 psig (4.14 N/mm2) max3 in. (76 mm) NPS and under 400 psig (2.76 N/mm2) max5.7 Threaded pipe joints above 2 in. (50 mm) NPS shall notbe used in systems t

    24、hat require radiographic examination (see8.2.2).6. Workmanship, Finish, and Appearance6.1 CleaningThe internal and external surfaces of the balljoint shall be cleaned of dirt and other foreign material using asuitable cleaner.6.2 Surface PreservationUnless otherwise specified bythe purchaser, the ba

    25、ll joint shall be coated in accordance withthe manufacturers standard practice.7. Test Methods or Analytical Methods7.1 Qualification Tests:7.1.1 A ball joint of each standard design shall be certifiedas having undergone the following qualification tests. The balljoint shall not show leakage of the

    26、test fluid under theconditions of pressurization stipulated in each test.7.1.1.1 Flex Cycle TestThe ball joint shall be subjected to8000 flex cycles at MAWP and maximum rated temperatureover the rated flex angle. Each flex cycle shall consist ofrotating the ball joint from maximum flex angle on one

    27、sidethrough 0 to maximum flex angle on the other side and returnto the original position. The flex cycle rate shall not exceed 4cpm. At the end of 8000 cycles, MAWP shall be held for atleast12 h.7.1.1.2 Thermal CyclingBall joints rated above 200Fshall be subjected to 100 saturated steam pressure cyc

    28、les fromatmospheric pressure to MAWP and back to atmosphericpressure. Each cycle shall permit the joint to reach saturatedsteam temperature at MAWP and then cool to ambient tem-perature. At the end of test, MAWP shall be held for12 hatsaturated steam temperature.7.2 Production Tests:7.2.1 Each ball

    29、joint shall be subjected to a hydrostatic testconducted at 112 times the 100F (38C) rated maximumallowable working pressure of the ball joint. The test shall bemade with water or other fluid having a maximum viscosity of40 SSU at 125F (52C). Minimum duration of test shall be 15s for ball joints less

    30、 than 2 in. (50 mm) nominal pipe size, 1 minfor ball joints 212 in. (63.5 mm) through 8 in. (203 mm), and3 min for larger sizes. The purpose of this test is to detect leaksand structural imperfections. No visible leakage is permitted.7.2.1.1 The pressure-containing boundary components ofeach ball jo

    31、int may be individually hydrostatically testedprovided that an assembled prototype has been subjected to ahydrostatic test as outlined in 7.2.1.7.2.1.2 The test arrangement shall be air-free prior topressurization.7.2.2 Ball joints of 2 in. (50 mm) NPS and smaller withother than flanged connections

    32、may, at the option of themanufacturer, be air tested to the lesser of 1.2 times the MAWPor 80 psig (0.55 N/m2). The minimum duration of the test shallbe 15 s. Visually detectable leakage through the pressure-retaining walls is not acceptable.7.2.2.1 If this option is exercised, the manufacturer shal

    33、l beable to certify that a prototype from each production lot of thesame size ball joint was subjected to a hydrostatic test inaccordance with 7.2.1.F 1298 90 (2006)28. Inspection8.1 Each finished ball joint shall be visually examined anddimensionally checked to ensure it corresponds to this speci-f

    34、ication.8.2 Nondestructive Examination of Welds:8.2.1 All welds shall be visually examined in accordancewith ANSI B 31.1.8.2.2 Welded inlet and outlet connections that are equal toor greater than 4 in. nominal diameter or greater than 0.375 in.nominal wall thickness that are in the following service

    35、s shallbe 100 % radiographically examined:Service Pressure, psig (N/mm2) Temperature, F (C)Fuel oil above 150 (1) or above 150 (65)Steam above 150 (1) or above 650 (343)Flammable cargo above 225 (1.55) or above 150 (65)Water above 225 (1.55) or above 350 (194)9. Keywords9.1 ball joints; marine pipel

    36、ine; marine technology; ships;thermal contraction; thermal expansionASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any

    37、 such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are in

    38、vited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not receive

    39、d a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).F 1298 90 (2006)3


    注意事项

    本文(ASTM F1298-1990(2006) Standard Specification for Flexible Expansion-Type Ball Joints for Marine Applications《船用柔性扩展型球连接》.pdf)为本站会员(tireattitude366)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开