1、Designation: F 1072 94 (Reapproved 2006)An American National StandardStandard Specification forExpanded-Metal Doors1This standard is issued under the fixed designation F 1072; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the yea
2、r of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers steel expanded-metal doorssuitable for installation in expanded-metal bulkheads, struc
3、-tural bulkheads, and structural arches.1.2 The values stated in inch-pound units are to be regardedas the standard. The values given in parentheses are forinformation only.2. Referenced Documents2.1 ASTM Standards:2A 36/A 36M Specification for Carbon Structural SteelA 167 Specification for Stainles
4、s and Heat-ResistingChromium-Nickel Steel Plate, Sheet, and StripD 3951 Practice for Commercial PackagingF 783 Specification for Staple, Handgrab, Handle, and Stir-rup Rung2.2 Other Documents:ABS Rules for Building and Classing Steel Vessels3AWS D1.1 Structural Welding Code43. Classification3.1 Expa
5、nded-metal doors are furnished in four types (seeDetail “J”) as follows:3.1.1 Type IRight hand (RH).3.1.2 Type IILeft hand (LH).3.1.3 Type IIIRight hand reverse (RHR).3.1.4 Type IVLeft hand reverse (LHR).4. Ordering Information4.1 Orders for doors under this specification shall includethis specifica
6、tion number and type.5. Materials and Manufacture5.1 MaterialsSee Table 1.5.2 Manufacture:5.2.1 Doors shall be furnished with the vertical supportchannels and top angle in place. A temporary brace shall beincluded at the frame bottom to prevent racking.5.2.2 Welding shall be in accordance with AWS D
7、1.1 Struc-tural Welding Code or ABS Rules for Building and ClassingSteel Vessels.6. Installation Requirements6.1 Doors shall be fitted with rubber-tipped bumpers and amanually operated catch for holding doors in an open position.These shall be furnished and installed by others.6.2 Provision shall be
8、 made for the installation of a rim latchset operated by knobs on both sides. This hardware shall befurnished and installed by others.6.3 Padlocks shall be furnished by others.6.4 Any holes needed in the frame for installation inexpanded-metal or other types of bulkheads shall be made atinstallation
9、 by others.7. Dimensions and Tolerances7.1 Dimensions are as indicated in Figs. 1-8 and Table 1.7.2 Tolerance6116 in. (1.5 mm).8. Workmanship, Finish, and Appearance8.1 Doors and frames shall be free from all cracks, burrs,sharp edges, and other defects.8.2 The door manufacturer shall apply a nonhaz
10、ardouscorrosion-inhibiting primer coating to all door assemblies.9. Packaging and Package Marking9.1 Each expanded-metal door shall be individually packedfor shipment and storage in accordance with Practice D 3951.9.2 In addition to any special marking required by thecontract or purchase order, each
11、 expanded-metal door shall bemarked in accordance with Practice D 3951.10. Keywords10.1 expanded-metal doors; expanded-metal bulkheads;metal doors; structural arches; structural bulkheads1This specification is under the jurisdiction of ASTM Committee F25 on Shipsand Marine Technology and is the dire
12、ct responsibility of Subcommittee F25.03 onOutfitting and Deck Machinery.Current edition approved May 1, 2006. Published May 2006. Originallyapproved in 1987. Last previous edition approved in 1999 as F 1072 94 (1999).2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact AS
13、TM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from American Bureau of Shipping, ABS Plaza 16855 NorthchaseDr., Houston, TX 77060.4Available from American Welding Society, 550 N.W
14、. Le Jeune Rd., Miami, FL33126.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.TABLE 1 Expanded-Metal Door MaterialsNOTE 11 in. = 25.4 mm.ItemNumberDescription1 Frame TopAngle, 6 3 3 3516 in., Specification A 36/A 36M.2 Frame SideCha
15、nnel, C3 3 5.0, Specification A 36/A 36M.3 StapleRound bar, Specification F 783.4 Door FrameAngle, 1 3 1 3 in., Specification A 36/A 36M.5 BraceFlat bar, 2 3 in., Specification A 36/A 36M.6 Cross BraceFlat bar, 2 3 in., Specification A 36/A 36M.7 StopFlat bar, 4 3 in., Specification A 36/A 36M.8 Pad
16、Flat bar, 4 3 in., Specification A 36/A 36M.9 HingeSwaged butt, plain, fixed pin, 3- 3 2-in. Type 316 stain-less steel, Specification A 167.10 Expanded Metal13-gage 3 -in. flat pattern, SpecificationA 36/A 36M.11 Temporary BraceAngle 1 3 1 3 in., Specification A 36/A 36M. (See 5.2.1.)F 1072 94 (2006
17、)2NOTE 11 in. = 25.4 mm.FIG. 1 Right-Hand Door and Frame AssemblyType I (Left Hand, Type II Not Shown)F 1072 94 (2006)3NOTE 11 in. = 25.4 mm.FIG. 2 Right-Hand Reverse Door and Frame AssemblyType III (Left Hand, Type IV Not Shown)F 1072 94 (2006)4NOTE 11 in. = 25.4 mm.FIG. 3 FrameNOTE 11 in. = 25.4 m
18、m.FIG. 4 DoorF 1072 94 (2006)5NOTE 11 in. = 25.4 mm.FIG. 5 PadNOTE 11 in. = 25.4 mm.FIG. 6 StopNOTE 11 in. = 25.4 mm.FIG. 7 Brace and Cross BraceF 1072 94 (2006)6NOTE 11 in. = 25.4 mm.FIG. 8 Installation DetailsASTM International takes no position respecting the validity of any patent rights asserte
19、d in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by th
20、e responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive
21、careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM Internat
22、ional, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).F 1072 94 (2006)7
