欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM F1006-1986(2018) Standard Specification for Entrainment Separators for Use in Marine Piping Applications.pdf

    • 资源ID:533965       资源大小:67.46KB        全文页数:3页
    • 资源格式: PDF        下载积分:5000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要5000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM F1006-1986(2018) Standard Specification for Entrainment Separators for Use in Marine Piping Applications.pdf

    1、Designation: F1006 86 (Reapproved 2018) An American National StandardStandard Specification forEntrainment Separators for Use in Marine PipingApplications1This standard is issued under the fixed designation F1006; the number immediately following the designation indicates the year oforiginal adoptio

    2、n or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers the minimum requirements forthe pressure-temperat

    3、ure rating, testing, and making ofpressure-containing vessels for entrainment separators.1.2 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered stand

    4、ard.1.3 The following safety hazards caveat pertains only to thetest methods portion, Section 6, of this specification: Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It is the responsibility of the userof this standard to establish appropriate s

    5、afety, health, andenvironmental practices and determine the applicability ofregulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of

    6、International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ANSI Standards:2B2.1 Pipe Threads (Except Dryseal)B16.31 Non-Ferrous Pipe Flanges2.2 ASME Standards:3B16.1 Gray Iron Pipe Flanges and Flan

    7、ged Fittings: Classes25, 125, and 250B16.3 Malleable Iron Threaded Fittings: Classes 150 and300B16.4 Gray Iron Threaded Fittings: Classes 125 and 250B16.5 Pipe Flanges and Flanged Fittings: NPS 1/2 throughNPS 24 Metric/Inch StandardB16.11 Forged Fittings, Socket-Welding and ThreadedB16.15 Cast Coppe

    8、r Alloy Threaded Fittings: Classes 125and 250B16.24 Cast Copper Alloy Pipe Flanges, Flanged Fittings,and Valves: Classes 150, 300, 600, 900, 1500, and 2500B16.25 Buttwelding EndsSA-278 Cast Gray Iron Pressure VesselsSA-395-60 Cast Ductile Iron2.3 ASME Boiler and Pressure Vessel Codes:3Section IISect

    9、ion VIII2.4 MSS Standards:4MSS-SP-51 Class 150LW Corrosion Resistant Flanges andCast Flanged Fittings2.5 Military Standards:5MIL-F-1183 Fittings Tube, Bronze, Cast (Silver Brazings)3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 entrainment separator, na mechanical device in-s

    10、erted in a pipeline which by centrifugal force, baffles, or othermeans will separate a liquid from a gas (vapor).3.1.2 hydrostatic test, nthe act of filling an entrainmentseparator vessel with water and applying internal pressure to allparts of the vessel.3.1.3 master gage, nthe calibrated gage used

    11、 to verify theaccuracy of the test gage. This gage shall be recalibratedtraceable to the National Bureau of Standards.3.1.4 pressure rating, nthe maximum working pressure ofan entrainment separator when operated at a specific tempera-ture.3.1.5 proof test, nthe act of filling an entrainment separa-t

    12、or vessel with water and applying internal pressure to all parts1This specification is under the jurisdiction of Committee F25 on Ships andMarine Technology and is the direct responsibility of Subcommittee F25.11 onMachinery and Piping Systems.Current edition approved Sept. 1, 2018. Published Octobe

    13、r 2018. Originallyapproved in 1986. Last previous edition approved in 2014 as F1006 86 (2014)1.DOI: 10.1520/F1006-86R18.2Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.3Available from American Society of Mechanical Engine

    14、ers (ASME), ASMEInternational Headquarters, Two Park Ave., New York, NY 10016-5990, http:/www.asme.org.4Available from Manufacturers Standardization Society of the Valve and FittingsIndustry (MSS), 127 Park St., NE, Vienna, VA 22180-4602, http:/www.mss-hq.org.5Available from DLA Document Services, B

    15、uilding 4/D, 700 Robbins Ave.,Philadelphia, PA 19111-5094, http:/quicksearch.dla.mil.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on

    16、standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.1of the vessel for the purpose of causing yielding of the vesseland bursting of the v

    17、essel.3.1.6 temperature ratings, nminimum and maximum tem-peratures at which the entrainment separator may be operatedwhile at specific pressures.3.1.7 test gage, nthe pressure gage that is used to checkthe internal pressure of the entrainment separator. The test gageshall be calibrated at least ann

    18、ually or at any time it issuspected to be in error by a calibrated master gage.4. Materials and Manufacture4.1 The pressure-temperature ratings established under thisspecification are based upon the manufacturers usage of highquality materials produced under regular control of chemicaland physical p

    19、roperties by a recognized process. The manu-facturer shall be prepared to submit certification of compliance,verifying that his product has been so produced and that it hasbeen manufactured from material with chemical and physicalproperties at least equal to the requirements of the appropriatestanda

    20、rd or specification listed in 4.3 of this specification orSection II of the ASME Boiler and Pressure Vessel Code.4.2 For materials not having values of allowable stresstabulated in Section VIII, Division I, of the ASME Boiler andPressure Vessel Code, allowable stresses shall be determined inaccordan

    21、ce with the procedures outlined in Appendix P ofSection VIII, Division 1, of the ASME Boiler and PressureVessel Code.4.3 Materials of construction shall be suitable for the serviceintended.4.4 Bolting materials shall be at least equal to those listed inTable 1B of ASME B16.5. Bolting materials shall

    22、 not be usedbeyond temperature limits specified in the governing codes.5. Requirements5.1 Entrainment separators covered in this specificationshall be designed according to the lowest pressure-temperaturerating of any individual component, or as established by prooftests.5.2 The design pressure-temp

    23、erature of entrainment separa-tors covered in this specification will be established by themanufacturer using one of the following methods:5.2.1 Design calculations in accordance with the require-ments prescribed in the ASME Boiler and Pressure VesselCode, Section VIII, Division 1, Part UG, of Subse

    24、ction A andthe applicable part of Subsection C.5.2.2 Proof test in accordance with the requirements of UG101 (m), UCI-101, or UCD-101 of Section VIII, Division 1, ofthe ASME Boiler and Pressure Vessel Code.5.2.3 Where any part of the entrainment separator vesselcannot be designed within the scope of

    25、 the ASME Boiler andPressure Vessel Code, Section VIII, Division 1, DesignSection, the pressure-temperature rating must be determinedthrough proof and hydrostatic tests using the following formu-las to determine the allowable operating limits of pressure andtemperature. Operator safety should be con

    26、sidered when con-ducting these tests.P 5SPHT4D3SS1S2D for steel vessels!P 5SPHT4D3ST1T2D for cast-iron vessels!where:P = maximum allowable working pressure (psig) at designtemperature,PHT= hydrostatic test pressure (psig) at test temperature,S1= stress value at design temperature (psi),S2= stress va

    27、lue at test temperature (psi),T1= specified minimum tensile strength (psi), andT2= actual tensile strength test specimen (psi).5.2.3.1 Stress values S1and S2are determined from SectionVIII, of the ASME Boiler and Pressure Vessel Code.5.2.3.2 The value of PHTto be used in determining themaximum allow

    28、able working pressure shall be the maximumpressure to which the entrainment separator was subjected towithout permanent deformation or rupture.5.2.3.3 Test water temperature6and entrainment separatortemperature must be at equilibrium before hydrostatic testpressure is applied.5.2.3.4 All possible ai

    29、r pockets must be purged while theentrainment separator vessel is being filled with water. Ad-equate vents shall be provided at all high points of the vessel.5.2.3.5 External equipment not to be pressurized with theentrainment separator should be isolated or disconnectedbefore applying the hydrostat

    30、ic test pressure.5.2.3.6 Hydrostatic test pressure shall be applied graduallyto the entrainment separator and held stationary at eachincrement for a sufficient time in order that a visual inspectioncan be made for leaks or deformation of the vessel. The finalvalue of hydrostatic test pressure that i

    31、s not in conflict with5.2.3.2 is called PHT.5.3 Pressure-temperature rating and construction of all pipeconnections shall be in accordance with the following stan-dards or specifications: ANSI B2.1, ASME B16.1, ASMEB16.3, ASME B16.4, ASME B16.5, ASME B16.11, ASMEB16.15, ASME B16.24, ASME B16.25, ASM

    32、E SA-278, ANSIB16.31, MSS-SP-51, and MIL-F-1183.6. Test Methods6.1 All entrainment separators must be pressure tested inaccordance with the following:6.1.1 Each entrainment separator shall be tested by subject-ing it to an internal hydrostatic test procedure, which at everypoint in the separator is

    33、at least equal to 1.5 times themaximum allowable working pressure, multiplied by the low-est ratio of the stress value for the design temperature.Test pressure 5 1.5 3maximum allowable pressure3stress value at test temperaturestress value at design temperature6Test water temperature to be no less th

    34、an 60F (10C), but not to exceed 125F(52C).F1006 86 (2018)26.1.1.1 The hydrostatic test pressure shall be held stationaryfor a suitable time necessary for observation and inspection ofthe separator. The minimum time of test shall be no less than1 min.6.1.1.2 A test gage, as defined in this specificat

    35、ion (seeSection 3) shall be connected directly to the entrainmentseparator.6.1.1.3 For compliance withASME Codes leading toASMEcertification, proceed with steps as outlined in Section VIII,Division 1, of the ASME Boiler and Pressure Vessel Code forStandard Hydrostatic Tests.7. Packaging and Package

    36、Marking7.1 Each entrainment separator shall have a securely at-tached nameplate or other permanent marking indicating thefollowing:7.1.1 Manufacturers name and trademark,7.1.2 Pressure-temperature rating,7.1.3 Manufacturers serial number,7.1.4 Year built,7.1.5 Size (end connection pipe size),7.1.6 F

    37、low direction,7.1.7 National board number, where applicable,7.1.8 ASME code stamp, where applicable, and7.1.9 ASTM designation and year of issue.8. Keywords8.1 entrainment separators; marine piping; piping applica-tionsASTM International takes no position respecting the validity of any patent rights

    38、 asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any ti

    39、me by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will

    40、receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM

    41、International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 86 (2018)3


    注意事项

    本文(ASTM F1006-1986(2018) Standard Specification for Entrainment Separators for Use in Marine Piping Applications.pdf)为本站会员(dealItalian200)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开