欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM E795-2005(2012) 9375 Standard Practices for Mounting Test Specimens During Sound Absorption Tests《吸声试验期间试样安装的标准实施规程》.pdf

    • 资源ID:533540       资源大小:562.78KB        全文页数:10页
    • 资源格式: PDF        下载积分:5000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要5000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM E795-2005(2012) 9375 Standard Practices for Mounting Test Specimens During Sound Absorption Tests《吸声试验期间试样安装的标准实施规程》.pdf

    1、Designation: E795 05 (Reapproved 2012)Standard Practices forMounting Test Specimens During Sound Absorption Tests1This standard is issued under the fixed designation E795; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of

    2、 last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 These practices cover test specimen

    3、mountings to beused during sound absorption tests performed in accordancewith Test Method C423.1.2 The values stated in SI units are to be regarded as thestandard. The values given in parentheses are for informationonly.2. Referenced Documents2.1 ASTM Standards:2C423 Test Method for SoundAbsorption

    4、and SoundAbsorp-tion Coefficients by the Reverberation Room MethodC634 Terminology Relating to Building and EnvironmentalAcoustics2.2 ISO Standard:ISO 354 Measurement of Sound Absorption in a Reverbera-tion Room33. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 Except as noted i

    5、n 4.2, the terms used in thesepractices are defined in Terminology C634.3.2 The following terms have the meaning noted for thesepractices only:3.2.1 sound-absorbing units consists of test specimensthat are in direct contact with or suspended from ceilings,walls, or other room surfaces. Sound-absorbi

    6、ng units include,but are not limited to, baffles, draperies, space absorbers,volume absorbers (bass traps), and other three-dimensionalobjects.3.2.2 test surfaceany hard surface over which the testspecimen or test specimen mounting is placed for testing inaccordance with Test Method C423. The surfac

    7、e shall satisfythe room construction requirements of Test Method C423.Inmost cases, the surface will be the floor of the reverberationroom.4. Significance and Use4.1 The sound absorption of a material that covers a flatsurface depends not only on the physical properties of thematerial but also on th

    8、e way in which the material is mountedover the surface. The mountings specified in these practices areintended to simulate in the laboratory conditions that exist innormal use.4.2 Some of the specified mountings require special fixturesor minor deviations from normal practice. These fixtures ordevia

    9、tions are to be used only during laboratory tests andshould not be specified for practical installations. They arenoted in the specifications for the mountings in question by thephrase “for laboratory testing only.”4.3 Test reports may refer to these mountings by typedesignation instead of providing

    10、 a detailed description of themounting used.5. Classification5.1 The mountings are designated as follows:5.1.1 Type A MountingTest specimen laid directly againstthe test surface (described in detail in Section 6).5.1.2 Type B MountingTest specimen cemented to gyp-sum board and laid directly against

    11、the test surface (describedin detail in Section 7).5.1.3 Type C MountingTest specimen comprising sound-absorptive material behind a perforated, expanded, open facingor other porous material (described in detail in Section 8).5.1.4 Type D MountingTest specimen mounted on woodfurring strips (described

    12、 in detail in Section 9).5.1.5 Type E MountingTest specimen mounted with an airspace behind it (described in detail in Section 10).5.1.6 Type F MountingTest specimen mounted with an airspace behind it (described in detail in Section 11).1These practices are under the jurisdiction of ASTM Committee E

    13、33 onBuilding and Environmental Acoustics and are the direct responsibility of Subcom-mittee E33.01 on Sound Absorption.Current edition approved Sept. 1, 2012. Published November 2012. Originallyapproved in 1981. Last previous edition approved in 2005 as E795 05. DOI:10.1520/E0795-05R12.2For referen

    14、ced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute (ANSI), 25 W. 43rd

    15、St.,4th Floor, New York, NY 10036.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States15.1.7 Type G MountingTest specimen is a drapery, win-dow shade, or blind hung parallel to the test surface (describedin detail in Section 12).5.1.8 Type

    16、 H MountingTest specimen is a drapery sus-pended away from any vertical surface (described in detail inSection 13).5.1.9 Type I MountingThe specimen is a spray- or trowel-applied material on an acoustically hard substrate (described indetail in Section 14).5.1.10 Type J MountingThe specimen is a sou

    17、nd-absorbing unit or set of sound-absorbing units (described indetail in Section 15).5.1.11 Type K MountingTest specimen is an office screen(described in detail in Section 16).5.1.12 Type L MountingThis mounting is for use withconcrete blocks or block-like specimens that are normallyassembled using

    18、mortar (described in detail in Section 17).5.1.13 Type M MountingTest specimen is theater seats, (described in detail in Section 18).5.2 Type C, D, E, and G mountings are further designatedby a numerical suffix which indicates the distance (in millime-tres) from the specimen to the test surface roun

    19、ded to thenearest integral multiple of 5 mm. For example, a Type E-400mounting is a plenum mounting in which the face of the testspecimen is 400 mm (1534 in.) away from the test surface. Thedistances specified by the suffixes are as follows:5.2.1 For a Type C MountingThe thickness of the furringstri

    20、ps.5.2.2 For a Type D MountingThe thickness of the furringstrips.5.2.3 For a Type E MountingThe distance from theexposed face of the test specimen to the test surface.5.2.4 For a Type F MountingThe thickness of the spacers.5.2.5 For a Type G MountingThe distance from thecenterline of the hangers to

    21、the test surface.6. Type A Mounting6.1 Lay the test specimen directly against the test surface asshown in Fig. 1.6.2 Do not use an adhesive that is likely to leave a thin airspace behind the test specimen. However, mechanicalfasteners, carpet tape, or contact cement may be used to holdthe specimen a

    22、gainst a vertical or overhead surface or to keepthe specimen in contact with the floor.6.3 If two or more pieces of material (or separate panels) arebutted together to form the test specimen, it may be advisableto cover the joints between adjacent pieces with tape, caulkingcompound, or other materia

    23、l that is not sound absorptive. If thejoints are sealed in this manner, the test report shall describethe method of sealing.6.4 Perimeter Seals for Laboratory Testing OnlyIf theperimeter edges of the test specimen are not exposed in normaluse, seal them by one of the following two methods:6.4.1 Cove

    24、r with tape, caulking compound, or a similarproduct as shown in Fig. 2.6.4.2 Cover with a wood or metal frame so that the topsurface of the frame is flush with the front face of the testspecimen as shown in Fig. 2. Minimize air spaces between theframe and the perimeter edge of the test specimen. Air

    25、 gapsbetween the bottom of the frame and the test surface shall besealed with duct tape or caulking.NOTE 1The Type A mounting is intended to simulate normal usewhere a product, such as carpet, wall panels, or ceiling tile is either laiddirectly on the floor or attached to a wall or ceiling with adhe

    26、sive ormechanical fasteners. Panels or tiles arranged as independent units, that is,not butted together at the edges to form a single extended plane, are to betested as a Type J mounting.7. Type B Mounting7.1 Adhere the test specimen to gypsum board laid directlyagainst the test surface as shown in

    27、Fig. 3. The thickness of thegypsum board is not critical.7.2 Apply the adhesive in accordance with the manufactur-ers instructions. If there are no specific instructions, apply fourdaubs of adhesive to the back of each piece of the testspecimen.7.3 For Laboratory Testing OnlyPlace 3 by 25 by 25-mm(1

    28、8 by 1 by 1-in.) hardboard shims between the test specimenand the gypsum board at the four corners of each piece of testspecimen.7.4 Perimeter Seals, for Laboratory Testing OnlySeal theperimeter edges of the test specimen by one of the followingmethods:7.4.1 Cover with tape, caulking compound, or a

    29、similarproduct as shown in Fig. 2.7.4.2 Cover with a wood or metal frame so that the topsurface of the frame is flush with the front face of the testspecimen as shown in Fig. 2. Minimize air spaces between theframe and the perimeter edge of the test specimen. Air gapsbetween the bottom of the frame

    30、and the test surface shall besealed with duct tape or caulking.NOTE 2The Type B mounting is intended to simulate acousticalceiling tiles or other sound-absorptive products adhered to a hard surfacewith an adhesive. In normal use, this method of application leaves a thinair space between the product

    31、and the surface to which it is adhered. TheFIG. 1 Type A MountingE795 05 (2012)23-mm (18-in.) thick hardboard shims are used to control the depth of theair space during laboratory tests and should not be included in a normalinstallation.8. Type C Mounting8.1 The test specimen shall comprise sound-ab

    32、sorptive ma-terial behind a perforated, expanded, open facing, or otherporous material attached to wood furring strips spaced 600 mm(24 in.) on centers and laid directly against the test surface asshown in Fig. 4. The suffix of the mounting designation shallbe the actual thickness of the furring str

    33、ips rounded to thenearest integral multiple of 5 mm.8.1.1 The length of the furring strips described in 8.1 shallbe shorter than the length of the test specimen by an amountequal to twice the width of the furring strips. This will allowFIG. 2 Typical Edge SealsFIG. 3 Type B MountingE795 05 (2012)3th

    34、e placement of a furring strip at each end of the system to actas an “end cap” and completely enclose the airspace below thetest specimen.8.2 Perimeter Seals, for Laboratory Testing OnlyTheperimeter furring strips of the test specimen shall be sealed tothe test surface with tape or caulking compound

    35、.NOTE 3The preferred sizes for furring strips are 20 by 40 mm (34 by112 in.) or 40 by 40 mm (112 by 112 in.), which corresponds to a C-20 orC-40 mounting.9. Type D Mounting9.1 Attach the test specimen to wood furring strips spaced at300 mm (12 in.) on centers and laid directly against the testsurfac

    36、e as shown in Fig. 5. The suffix of the mountingdesignation shall be the actual thickness of the furring stripsrounded to the nearest integral multiple of 5 mm.9.1.1 The length of the furring strips described in 9.1 shallbe shorter than the length of the test specimen by an amountequal to twice the

    37、width of the furring strips. This will allowthe placement of a furring strip at each end of the system to actas an “end cap” and completely enclose the airspace below thetest specimen.9.2 Perimeter Seals, for Laboratory Testing OnlySeal theperimeter edges of the test specimen by one of the following

    38、methods:9.2.1 Cover with tape, caulking compound, or a similarproduct as shown in Fig. 2.9.2.2 Cover with a wood or metal frame so that the topsurface of the frame is flush with the front face of the testspecimen as shown in Fig. 2. Minimize air spaces between theframe and the perimeter edge of the

    39、test specimen. Air gapsbetween the bottom of the frame and the test surface shall besealed with duct tape or caulking.NOTE 4The preferred size for furring strips is 20 by 40 mm (34 by 112in.). This is a D20 mounting.NOTE 5If a different on center spacing of the wood furring strips isused, the spacin

    40、g shall be noted in the report.10. Type E Mounting10.1 Mount the test specimen in a fixture that supports theexposed face of the specimen at a designated distance from thetest surface as shown in Fig. 6. The suffix of the mountingdesignation shall be the distance between the exposed face ofthe speci

    41、men and the test surface rounded to the nearestintegral multiple of 5 mm.10.2 Mounting Fixture for Laboratory Testing OnlyThemounting fixture shall satisfy the following requirements:10.2.1 The mounting fixture, test specimen, and test surfaceshall enclose an air space that has no interior partition

    42、s.10.2.2 The joint between the fixture and the test surfaceshall be sealed to prevent air leaks between the enclosed spaceand the outside.10.2.3 The fixture shall include a rigid grid system thatsupports the exposed face of the test specimen at the requireddistance from the test surface. The distanc

    43、e from the exposedface of the test specimen (excluding decorative features) to thetest surface shall not vary by more than 5 mm (0.20 in.), acrossthe entire face of the specimen.10.2.4 The fixture shall seal the perimeter edges of the testspecimen, and the top surface of the fixture shall be flush w

    44、iththe front face of the test specimen as shown in Fig. 6.10.2.5 The mounting fixture shall be made of a sturdymaterial, such as 20-mm (34-in.) thick plywood or 3-mm(18-in.) thick aluminum.10.2.6 If a grid system is placed between the panels, on theexposed side of the specimen, the grid size and arr

    45、angementshall be noted in the report.NOTE 6Type E mountings are intended to simulate a suspendedceiling with an open plenum above it.NOTE 7When there is good reason to test on a Type E mounting otherthan Type E-400, a mounting whose suffix is an integral multiple of 25 ispreferred (for example, E-37

    46、5, E-425, and so forth).NOTE 8It has been found that if a gasket is used between the testfixture and the test surface, placing the gasket so that it is flush with theexterior surface of the test fixture will minimized the variability in results.FIG. 4 Type C MountingFIG. 5 Type D MountingE795 05 (20

    47、12)411. Type F Mounting11.1 Lay the test specimen with spacers against the testsurface as shown in Fig. 7. If spacers are not an integral part ofthe specimen then metal furring, solid wood blocks, or similaritems may be used to space the product away from the testsurface. The suffix of the mounting

    48、designation shall be theactual thickness of the spacers rounded to the nearest integralmultiple of 5 mm for spacers 10 mm thick or greater and to thenearest integral multiple of 1 mm for those less than 10 mm.NOTE 9Any specimen with a spacer less than 1 mm shall be testedand reported as Type A mount

    49、ing.11.2 If two or more pieces of material (or separate panels)are butted together to form the test specimen, it may beadvisable to cover the joints between adjacent pieces with tape,caulking compound, or other material that is not soundabsorptive. If the joints are sealed in this manner, the test reportshall describe the method of sealing.11.3 Perimeter Seals for Laboratory Testing OnlyIf theperimeter edges of the test specimen are not exposed in normaluse, seal them by one of the following two methods:11.3.1 Cover with tape, cau


    注意事项

    本文(ASTM E795-2005(2012) 9375 Standard Practices for Mounting Test Specimens During Sound Absorption Tests《吸声试验期间试样安装的标准实施规程》.pdf)为本站会员(sumcourage256)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开