欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM E1961-2016 Standard Practice for Mechanized Ultrasonic Testing of Girth Welds Using Zonal Discrimination with Focused Search Units《采用带有聚焦搜索组件的区域性辨别而对环缝焊接进行机械化超声波试验的标准实施规程》.pdf

    • 资源ID:529930       资源大小:493.83KB        全文页数:14页
    • 资源格式: PDF        下载积分:5000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要5000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM E1961-2016 Standard Practice for Mechanized Ultrasonic Testing of Girth Welds Using Zonal Discrimination with Focused Search Units《采用带有聚焦搜索组件的区域性辨别而对环缝焊接进行机械化超声波试验的标准实施规程》.pdf

    1、Designation: E1961 16Standard Practice forMechanized Ultrasonic Testing of Girth Welds Using ZonalDiscrimination with Focused Search Units1This standard is issued under the fixed designation E1961; the number immediately following the designation indicates the year oforiginal adoption or, in the cas

    2、e of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This practice covers the requirements for mechanizedultrasonic examination of girth welds.

    3、 Evaluation is basedupon the results of mechanized ultrasonic examination. Accep-tance criteria are based upon flaw limits defined by anEngineering Critical Assessment (ECA) or other accept/rejectcriteria defined by the Contracting Agency.1.2 This practice shall be applicable to the development ofan

    4、 examination procedure agreed upon between the users ofthis practice.1.3 The values stated in SI units are to be regarded as thestandard. The inch-pound units given in parentheses are forinformation only.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with

    5、 its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 The following documents form a part of this practice tothe extent specified herein:2

    6、.2 ASTM Standards:2E164 Practice for Contact Ultrasonic Testing of WeldmentsE317 Practice for Evaluating Performance Characteristics ofUltrasonic Pulse-Echo Testing Instruments and Systemswithout the Use of Electronic Measurement InstrumentsE543 Specification for Agencies Performing NondestructiveTe

    7、stingE1316 Terminology for Nondestructive Examinations2.3 ASNT Standard:3ASNT Practice SNT-TC-1A Personnel Qualification andCertification in Nondestructive TestingANSI/ASNT-CP-189 Standard for Qualification and Certifi-cation of Nondestructive Testing Personnel2.4 AIA Standard:NAS-410 Nondestructive

    8、 Testing Personnel Qualificationand Certification42.5 API Standard:API STD1104 Welding of Pipeline and Related Facilities52.6 CSA Standard:CSA Z-662 Oil and Gas Pipelines Systems62.7 ISO Standards7ISO 9712 Nondestructive TestingQualification and Certi-fication of NDT Personnel3. Terminology3.1 Defin

    9、itions:3.1.1 Definitions relating to ultrasonic examination, thatappear in Terminology E1316 shall apply to the terms used inthis practice.3.2 Definitions of Terms Specific to This Standard:3.2.1 acceptance criteriadefinition of acceptable/rejectable flaws as defined by an Engineering Critical Asses

    10、s-ment (ECA), such as defined in CSA-Z662 or API 1104, orworkmanship criteria as defined by the contracting agency.3.2.2 contract documentany document specified in thecontract between the contracting agency and contractor, includ-ing the purchase order, specification, drawings or other writtenmateri

    11、al.1This practice is under the jurisdiction of ASTM Committee E07 on Nonde-structive Testing and is the direct responsibility of Subcommittee E07.06 onUltrasonic Method.Current edition approved June 1, 2016. Published June 2016. Originallyapproved in 1998. Last previous edition approved in 2011 as E

    12、1961 - 11. DOI:10.1520/E1961-16.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available fromAmerican Socie

    13、ty for Nondestructive Testing (ASNT), P.O. Box28518, 1711 Arlingate Ln., Columbus, OH 43228-0518, http:/www.asnt.org.4Available from Aerospace Industries Association of America, Inc. (AIA), 1000Wilson Blvd., Suite 1700,Arlington, VA22209-3928, http:/www.aia-aerospace.org.5Available from American Pet

    14、roleum Institute (API), 1220 L. St., NW,Washington, DC 20005-4070, http:/www.api.org.6Available from Canadian Standards Association (CSA), 5060 Spectrum Way,Mississauga, ON L4W 5N6, Canada, http:/www.csa.ca.7Available from International Organization for Standardization (ISO), ISOCentral Secretariat,

    15、 BIBC II, Chemin de Blandonnet 8, CP 401, 1214 Vernier,Geneva, Switzerland, http:/www.iso.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States13.2.3 contracting agencya g

    16、overnment agency, primecontractor or subcontractor procuring ultrasonic examinationservices.3.2.4 contractorthe nondestructive examination contrac-tor engaged by the contracting agency in work covered by thispractice.3.2.5 mapping type presentationsan ultrasonic image pre-sentation whereby the digit

    17、ized A-scan signal is represented ascolors or grayscale for amplitude variation along one axisrepresenting time of flight and the other axis is the samplingposition, or the distance along the weld.3.2.6 operator(s)the term “operator(s)” as used in thispractice shall mean the operator(s) of ultrasoni

    18、c equipmentwho is (are) certified according to the requirements in 5.2 andat a level deemed acceptable to the contracting agency.4. Significance and Use4.1 This practice is intended primarily for the mechanizedultrasonic examination of pipe girth welds used in the con-struction of gas and oil pipeli

    19、nes. This practice, with appropri-ate modifications due to changes in weld profile, may also beused to examine repaired welds. Manual techniques such asdescribed in Practice E164 may also be used to examineproduction or repaired welds. This practice, with appropriatemodifications, may also be used t

    20、o examine other forms of buttwelds including long seams.4.2 Techniques used are to be based on zonal discriminationwhereby the weld is divided into approximately equal verticalexamination sections (zones) each being assessed by a pair ofultrasonic search units. See Fig. 1 for typical zones.4.3 Thick

    21、nesses of material examined are normally 7 to 25mm (0.28 to 1.00 in.) and pipe diameters 15 cm (6.0 in.) andgreater but this standard may apply to other thicknesses anddiameters if the techniques can be proven to provide therequired zonal discrimination.4.4 Examination zones are typically 2 to 3 mm

    22、(0.08 to 0.12in.) in height. For most applications this will require the use ofcontact focused search units to avoid interfering signals origi-nating from off-axis geometric reflectors and to avoid exces-sive overlap with adjacent zones.5. Basis of Application5.1 The following items are subject to c

    23、ontractual agree-ment between the parties using or referencing this standard.5.2 Personnel Qualification:5.2.1 If specified in the contractual agreement, personnelperforming examinations to this standard shall be qualified inaccordance with a nationally or internationally recognizedNDT personnel qua

    24、lification practice or standard such asANSI/ASNT-CP-189, SNT-TC-1A, NAS-410, ISO 9712, or asimilar document and certified by the employer or certifyingagency, as applicable. The practice or standard used and itsapplicable revision shall be identified in the contractual agree-ment between the using p

    25、arties.5.3 Qualification of Nondestructive AgenciesIf specifiedin the contractual agreement, NDT agencies shall be qualifiedand evaluated as described in Practice E543. The applicableedition of Practice E543 shall be specified in the contractualagreement.5.4 Procedures and TechniquesThe procedures a

    26、nd tech-niques to be used shall be as specified in the contractualagreement.5.5 Surface PreparationThe pre-examination surfacepreparation criteria shall be in accordance with 10.2, unlessotherwise specified.FIG. 1 Schematic Representation of Weld Zones and DiscontinuitiesE1961 1625.6 Timing of Exami

    27、nationThe timing of examinationshall be in accordance with 10.3, unless otherwise specified.5.7 Extent of ExaminationThe extent of examination shallbe in accordance with Section 8, unless otherwise specified.5.8 Reporting Criteria/Acceptance CriteriaReporting cri-teria for the examination results sh

    28、all be in accordance withSection 11, unless otherwise specified. Since acceptance crite-ria are not specified in this standard, they shall be specified inthe contractual agreement.5.9 Reexamination of Repaired/Reworked ItemsReexamination of repaired/reworked items is not addressed inthis standard an

    29、d if required shall be specified in the contrac-tual agreement.6. Examination Methods6.1 Visual ExaminationAll welds shall be visually exam-ined after completion and assessed in accordance with therequirements of surface conditions for ultrasonic examination.6.2 All bevels shall be examined immediat

    30、ely after machin-ing to ensure compliance with the applicable welding proce-dure. This examination should be combined with scribing thereference line as described in 10.4.6.3 Any items of non-compliance shall be referred to thecontracting agency representative for corrective action.6.4 Ultrasonic Ex

    31、aminationAll girth welds identified formechanized ultrasonic examination shall be examined for100 % of their circumference and assessed in accordance withthe contracting agencys acceptance criteria. Examinationshould be conducted in accordance with procedures approvedby the contracting agency.7. Ult

    32、rasonic Equipment7.1 Ultrasonic SystemThe system shall provide an ad-equate number of examination channels to ensure the completevolumetric examination of the weld through thickness in onecircumferential scan. The instrument shall provide a linear “A”scan presentation for each channel selected. The

    33、examinationchannels will allow the volume of the weld scanned to beassessed in accordance with the examination zones as typicallydefined in Fig. 1. Instrument linearity shall be determinedaccording to the procedures detailed in Practice E317, withinsix months of the intended end use date. The contra

    34、ctor shallretain a copy of the calibration certificate. Instrument linearityshall be such that the accuracy of any indicated amplitude iswithin 5 % of the actual full scale amplitude. This shall applyto both linear and logarithmic amplifiers. Each examinationchannel shall be selective for: pulse-ech

    35、o or through-transmission mode, gate position and length for a minimum oftwo gates, and gain. Recording thresholds shall be selectable todisplay signals between 0 and 100 % of full screen height forsimple amplitude and transit time recording and shall be from0 to 100 % for B-scan or “mapping” type r

    36、ecording of data.Two recordable signal outputs per gate shall be available, beingeither analog or digital and representative of signal height andtime of flight. These will be suitable for recording on amulti-channel recorder or computer data acquisition softwaredisplay.7.2 Recording System:7.2.1 A d

    37、istance measuring circuit or device suitable forconnection to the recorder or acquisition system shall providea means of electronically determining circumferential welddistance to an accuracy of typically 61 cm (0.4 in.) or better,as required by the contracting agency, over the circumferenceof the w

    38、eld (an optical encoder is typically used for suchdistance measurement). Programmed scan lengths shall besufficient to ensure all probes will travel the maximum circum-ferential distance required for a pipe having a diameter with themaximum tolerance allowed by the contracting agencys speci-fication

    39、. For equipment with encoders traveling on a track orwelding guide-band a correction factor will be incorporated toensure the circumferential distance recorded on the chartcorresponds to the search unit position on the pipe outersurface. The recording or marking system shall clearly indicatethe loca

    40、tion of discontinuities relative to the marked startingposition of the scan, with a 61 cm (0.4 in.) accuracy. Thereshall be recordings from each search unit for weld discontinui-ties and confirmation of the acoustic coupling arranged on thechart or display in a manner acceptable to the contractingag

    41、ency.7.2.2 B-scan or other form of “mapping” displays will beused for volumetric flaw detection and characterizations andTime of Flight Diffraction (TOFD) techniques may be added toimprove characterization and sizing. TOFD techniques mayaugment pulse-echo techniques but shall not replace pulse-echo

    42、techniques.7.2.3 Where TOFD techniques are employed the recordingsystem shall be capable of a 256-level grayscale display and becapable of recording full R-F wave forms for the TOFD searchunit pairs.7.3 CouplingThe coupling shall be obtained by using amedium suitable for the purpose. An environmenta

    43、lly safewetting agent may be required to enhance acoustic coupling.No residue should remain on the pipe surface after the liquidhas evaporated. For examination where ambient temperaturesare below 0C (32F) a methyl alcohol washer fluid or a similarmedium may be used. This liquid medium may be recover

    44、edand filtered for re-use. For examination where pipe cool-downmay be required after welding, water spray or other agents maybe used with contracting agency approval.7.4 Search Units:7.4.1 Each search unit shall be marked with a method toidentify the manufacturers name, search unit type, exit point,

    45、incident beam angle or refracted beam angle for a specificwedge/steel velocity ratio, frequency, and crystal size.87.4.2 The search unit array design shall be specific to theproject where the examination is to be performed.7.4.3 All search units shall be contoured to match thecurvature of the pipe s

    46、urface.7.5 Reference StandardsReference standards shall be usedto establish sensitivity and qualify the examination system forfield examination and to monitor the systems performance on8For phased array and EMAT probes, not all of the listed items may beapplicable.E1961 163an ongoing basis. Referenc

    47、e standards shall be manufacturedfrom a section of unflawed project-specific line pipe suppliedby the contracting agency. The contracting agency will providethe contractor with details of project-specific weld geometriesand the reference reflectors required in specific areas. Thecontractor shall the

    48、n provide a reference standard design thatmust be submitted to the contracting agency for approvalbefore manufacturing. No design changes to the referencestandard shall be made without prior approval of the contract-ing agency. Annex A3 provides an example of a typicalreference standard.7.6 Ultrason

    49、ic Examination ProcedureThe contractorshall provide a procedure that will provide examination criteriafor the ultrasonic examination of the weld in a single pass. Itmust allow for characteristic Hi/Lo fit-ups (edgemisalignment), weld shrinkage and be pipe-size specific. Pro-cedures submitted will allow zonal flaw characterization thatpermits use of the contracting agencys engineering criticalassessment acceptance criteria. It shall include but not belimited to describing the following requirements:7.6.1 The mechanized variable speed scanner mountable


    注意事项

    本文(ASTM E1961-2016 Standard Practice for Mechanized Ultrasonic Testing of Girth Welds Using Zonal Discrimination with Focused Search Units《采用带有聚焦搜索组件的区域性辨别而对环缝焊接进行机械化超声波试验的标准实施规程》.pdf)为本站会员(fuellot230)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开