欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM E1867-2012 Standard Test Method for Temperature Calibration of Dynamic Mechanical Analyzers《动态机械分析仪的温度校准用标准试验方法》.pdf

    • 资源ID:529678       资源大小:48.20KB        全文页数:7页
    • 资源格式: PDF        下载积分:5000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要5000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM E1867-2012 Standard Test Method for Temperature Calibration of Dynamic Mechanical Analyzers《动态机械分析仪的温度校准用标准试验方法》.pdf

    1、Designation: E1867 11 E1867 12Standard Test Method forTemperature Calibration of Dynamic Mechanical Analyzers1This standard is issued under the fixed designation E1867; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of la

    2、st revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method describes the temperature calibration of dynamic mechanical analyzers (DMA) from 150 C to 500 C.1.2 The

    3、 values stated in SI units are to be regarded as standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibilityof the user of this standard to establish appropriate safety and health practices and determine the applicabili

    4、ty of regulatorylimitations prior to use. Specific precautionary statements are given in Note 7.2. Referenced Documents2.1 ASTM Standards:2E473 Terminology Relating to Thermal Analysis and RheologyE1142 Terminology Relating to Thermophysical PropertiesE2161 Terminology Relating to Performance Valida

    5、tion in Thermal Analysis3. Terminology3.1 Definitions:3.1.1 The technical terms used in this test method are defined in Terminologies E473, E1142, and E2161, including dynamicmechanical analysis, frequency, stress, strain and storage modulus.4. Summary of Test Method4.1 An equation is developed for

    6、the linear correlation of experimentally observed program or sensor temperature and the actualmelting temperature for known melting reference materials. This is accomplished by loading melting point reference materials intoa polymer tube, or wrapping them with polymer tape and subjecting it to a mec

    7、hanical oscillation at either fixed or resonantfrequency. The extrapolated onset of melting is identified by a rapid decrease in the ordinate signal (the apparent storage modulus,stress, inverse strain or probe position). This onset is used for temperature calibration with two melting point referenc

    8、e materials.5. Significance and Use5.1 Dynamic mechanical analyzers monitor changes in the viscoelastic properties of a material as a function of temperature andfrequency, providing a means to quantify these changes. In most cases, the value to be assigned is the temperature of the transition(or eve

    9、nt) under study. Therefore, the temperature axis (abscissa) of all DMA thermal curves must be accurately calibrated byadjusting the apparent temperature scale to match the actual temperature over the temperature range of interest.6. Interferences6.1 An increase or decrease in heating rates or change

    10、 in purge gas type or rate from those specified may alter results.6.2 Once the temperature calibration procedure has been executed, the measuring temperature sensor position shall not bechanged, nor shall it be in contact with the specimen or specimen holder in a way that would impede movement. If t

    11、he temperaturesensor position is changed or is replaced, then the entire calibration procedure shall be repeated.1 This test method is under the jurisdiction of ASTM Committee E37 on Thermal Measurements and is the direct responsibility of Subcommittee E37.10 on Fundamental,Statistical and Mechanica

    12、l Properties.Current edition approved Aug. 1, 2011Sept. 1, 2012. Published September 2011October 2012. Originally approved in 1997. Last previous edition approved in 20062011as E1867 06.E1867 11. DOI: 10.1520/E1867-11.10.1520/E1867-12.2 For referenced ASTM standards, visit the ASTM website, www.astm

    13、.org, or contact ASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what ch

    14、anges have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the off

    15、icial document.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States16.3 Once the temperature calibration has been executed, the geometry deformation (bending study, versus tensile, and the like)shall not be changed. If the specimen testing

    16、 geometry differs significantly from that of the calibrants, then the calibration shallbe repeated in the geometry matching that of specimen testing.6.4 This method does not apply to calibration for shear or compressive geometries of deformation.7. Apparatus7.1 The function of the apparatus is to ho

    17、ld a specimen of uniform dimension so that the specimen acts as the elastic anddissipative element in a mechanically oscillated system. Dynamic mechanic analyzers typically operate in one of several modesas outlined in Table 1.7.1.1 The apparatus shall consist of the following:7.1.1.1 ClampsA clampi

    18、ng arrangement that permits gripping of the specimen. This may be accomplished by clamping at bothends (most systems), one end (for example, torsional pendulum) or neither end (for example, free bending between knife edges).7.1.1.2 Device to Apply Oscillatory Stress or StrainA device for applying an

    19、 oscillatory deformation (strain) or oscillatorystress to the specimen. The deformation may be applied and then released, as in freely vibrating devices, or continually applied,as in forced vibration devices.7.1.1.3 DetectorA device or devices for determining the dependent and independent experiment

    20、al parameters, such as force(stress), deformation (strain), frequency, and temperature. Temperature shall be measurable with an accuracy of 60.1 C, force to61 % and frequency to 61 %.7.1.1.4 Temperature Controller and OvenA device for controlling the specimen temperature, either by heating, cooling

    21、(insteps or ramps), or by maintaining a constant experimental environment. The temperature programmer shall be sufficiently stableto permit measurement of specimen temperature to 0.1 C.7.1.1.5 A Data Collection Device, to provide a means of acquiring, storing, and displaying measured or calculated s

    22、ignals, orboth. The minimum output signals required for dynamic mechanical analysis are storage modulus, loss modulus, tangent delta,temperature, and time.NOTE 1Some instruments, suitable for this test, may display only linear or logarithmic storage modulus while others may display linear and/orloga

    23、rithmic storage modulus. Care must be taken to use the same modulus scale when comparing unknown specimens, and in the comparison of resultsfrom one instrument to another.7.2 High Temperature Polymer Tubing such as PTFE (Polytetrafluoroethylene) or PEEK (Polyetheretherketone), of 3-mmoutside diamete

    24、r and wall thickness of 0.5-mm (0.002 in.)3 inner diameter may be used for low temperature standards (that is, lessthan 160 C). The tubing may be sealed with suitable melting temperature wax plugs, or similar sealant.NOTE 2PTFE tubing is selected for its flexibility and inert nature for the solvents

    25、 in use at the temperatures of interest. Furthermore its transitionsshould not produce any interference in the DMA signal within the range of the suggested calibrant materials. PEEK provides increased stiffness for easeof loading. For other temperature ranges, a suitable replacement for the high tem

    26、perature polymer tubing may be used.7.3 Where the melting material is to be confined to a tube7.4 PTFE Tape, for wrapping metal point standards.7.5 Calibration MaterialsOne or more suitable materials presented in Table 2.7.6 Calipers or other length measuring device capable of measuring dimensions (

    27、or length) within 610 m.8. Reagents and Materials8.1 Dry nitrogen, helium, or other inert gas supplied for purging purposes and especially to ensure that moisture condensationand ice formation is avoided when measurements involve temperatures below the dew point.3 Lotti, C., and Canevarolo.Canevarol

    28、o, S.V., “Temperature Calibration of a Dynamic Mechanical Dynamic-Mechanical Thermal Analyzer,” Polymer Testing, Vol 17, 1998,pp. 523530.TABLE 1 Dynamic Mechanical Analyzer Modes of OperationMode Mechanical ResponseTension Flexural Torsion CompressionFree/decA . . . . . . X . . .Forced/res/CAA . . .

    29、 X X . . .Forced/fix/CAA X X X XForced/fix/CSA X X . . . XA Free = free oscillation; dec = decaying amplitude; forced = forced oscillation;CA = constant amplitude; res = resonant frequency; fix = fixed frequency;CS = controlled stress.E1867 1229. Calibration and Standardization9.1 Prepare the instru

    30、ment for operation as dexcribed by the manufacturer in the operations manual10. Procedure10.1 Two Point CalibrationFor the purposes of this procedure, it is assumed that the relationship between observedextrapolated onset temperature (To) and actual specimen temperature (Tt) is a linear one governed

    31、 by the equation:Tt 5To 3S!1I (1)where: S and I are the slope and intercept of a straight line, respectively.10.2 Select two calibration standards near the temperature range of interest. The standards should be as close to the upper andlower temperature limits used for the subsequent test materials

    32、as practical.NOTE 3The purpose of the polymer encapsulation is to provide thermal resistance between the test specimen and the environment similar to thatoffered by polymer test specimens. In some testing geometries it may be possible to perform the test directly on the metal melting point reference

    33、 materialswithout encapsulation. (See Appendix X2.)10.2.1 Encapsulation technique for low temperature (liquid) standards where the melting temperature does not exceed 100 C.10.2.1.1 Fill the polymer tubing with the calibration material or wrap a solid calibrant with PTFE tape. Calibrant must extendt

    34、o the ends of the clamping geometry and must have uniform dimensions with respect to width.NOTE 4For solid calibrants, a wire of dimensions suitable for testing should be used.10.3 Measure the length and for solid calibrants the diameter as well, of specimens.10.4 Mount the specimen in accordance wi

    35、th the procedure recommended by the manufacturer.NOTE 5For specimen clamping arrangements where the specimen is not gripped on either end (for example, free bending between knife edges) thespecimen must be rigid enough at the test start temperature to sustain initial loading. Alternatively, the cali

    36、bration specimen, without encapsulation, canbe placed between the knife edge and a substrate.10.5 Maximum strain amplitude should be within the linear viscoelastic range of the specimens to be subsequently analyzed.Strains of less than 1 % are recommended and should not exceed 3 %.10.6 Conduct the c

    37、alibration runs at the heating rate of interest, preferably 1 C/min but no greater than 5 C/min and afrequency of 1 Hz. Other heating rates and frequencies may be used but shall be reported. (See Appendix X2.)NOTE 6Calibration for temperature should always be performed under the conditions of heatin

    38、g rate and frequency at which the unknown specimenswill be tested. This method does not address the issues of frequency affects for polymeric transitions (such as the upwards shift of glass transitiontemperature with increasing frequency), and will only compensate for thermal lag within the measurin

    39、g device.10.7 Measure and record the ordinate signal, from 30 C below to 20 C above the melting point of the reference material. Thecalibration specimen may be equilibrated a minimum of 50 C below the melting transition, but adequate time to achieve thermalequilibrium in the specimen must be allowed

    40、.11. Calculation11.1 Take the transition temperature as the extrapolated onset to the sigmoidal change in the ordinate signal observed in thedownward direction (see Fig. 1).TABLE 2 Calibration MaterialsMaterial Transition TemperatureAReferenceC KCyclopentane (solid-solid) 151.16 121.99 X1.1Cyclopent

    41、ane (solid-solid) 135.06 138.09 X1.1n-Heptane 90.56 182.65 X1.2Cyclohexane 87.06 186.09 X1.3n-Octane 56.76 216.39 X1.1n-Decane 26.66 246.49 X1.1n-Dodecane 9.65 263.5 X1.1Water 0.01 273.16 X1.4Cyclohexane 6.54 279.69 X1.3Indium 156.5985 495.7485 X1.4Tin 231.928 505.078 X1.4Lead 327.462 600.612 X1.5Zi

    42、ncB 419.527 692.677 X1.4A The values in this table were determined under special, highly accurate testconditions that are not attainable or applicable to this test method. The actualprecision of this test method is given in Section 13.B Amalgamates with aluminum. Do not heat above 430 C.E1867 12311.

    43、1.1 Construct a tangent to the ordinate signal curve below the transition temperature.11.1.2 Construct a tangent to the ordinate signal curve at the inflection point approximately midway through the sigmoidalchange associated with the transition.11.1.3 Report the temperature at which these tangent l

    44、ines intersect as reported as the observed transition temperature (To).11.2 Two Point Calibration:11.2.1 Using the standard temperature values from Table 2 and the corresponding onset temperatures obtained experimentally,calculate the slope and intercept using the following equations:S 5Tr12Tr2#/To1

    45、2To2# (2)I 5To13Tr22Tr13To2!#/To12To2# (3)whereS = slope (nominal value = 1.0000),I = intercept,Tr1 = reference transition temperature for Standard 1 (in Table 2),Tr2 = reference transition temperature for Standard 2 (in Table 2),To1 = experimentally observed transition onset temperatures for Standa

    46、rd 1, andTo2 = experimentally observed transition onset temperature for Standard 2.NOTE 7The slope S is a dimensionless number whose value is independent of which temperature scale is used for I and T.I, in all cases, must havethe same units as Tr1, Tr2, To1, and To2 that are, by necessity, consiste

    47、nt with each other.11.2.2 S should be calculated to 60.0001 units while I should be calculated to 60.1 C.11.2.3 Using the determined values for S and I,Eq 1 may be used to calculate the actual specimen transition temperature (Tt)from any experimentally observed transition temperature (To) for the pa

    48、rticular DMA instrument employed.11.3 One Point Calibration:11.3.1 In this abbreviated procedure, a relationship between the extrapolated onset temperature as observed and the temperatureas assigned by a temperature sensor is established. The operator should choose a calibration standard that is nea

    49、r the temperatureof the transition or phenomenon under study.11.3.2 Using the specimen handling techniques in 10.2 through 10.7, obtain the DMA curve for the calibration standard chosenfrom Table 2.11.3.3 From the known melting temperature of the calibration material (see Table 2), calculate the value and sign of from thefollowing equation:5Tr 2To (4)FIG. 1 Transition TemperatureE1867 124whereTr = reference transition temperature for standard (in Table 2),To = experimentally observed transition onset temperature for standard, an


    注意事项

    本文(ASTM E1867-2012 Standard Test Method for Temperature Calibration of Dynamic Mechanical Analyzers《动态机械分析仪的温度校准用标准试验方法》.pdf)为本站会员(visitstep340)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开