欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM E1215-1993(2003) Standard Specification for Trailers Used for Measuring Vehicular Response to Road Roughness《测量车辆对道路粗糙度的行车响应用挂车》.pdf

    • 资源ID:528183       资源大小:25KB        全文页数:2页
    • 资源格式: PDF        下载积分:5000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要5000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM E1215-1993(2003) Standard Specification for Trailers Used for Measuring Vehicular Response to Road Roughness《测量车辆对道路粗糙度的行车响应用挂车》.pdf

    1、Designation: E 1215 93 (Reapproved 2003)Standard Specification forTrailers Used for Measuring Vehicular Response to RoadRoughness1This standard is issued under the fixed designation E 1215; the number immediately following the designation indicates the year oforiginal adoption or, in the case of rev

    2、ision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This document covers the design, performance, andoperating features of a trailer used for measurin

    3、g response toroad roughness.1.2 The specified trailer is a two-wheeled, single-axle ve-hicle that is towed on highways at typical traffic speeds whilethe relative movement between the axle and body is transducedand recorded as an indication of road roughness.1.3 The instrumentation for sensing the m

    4、ovements of thetrailer is not covered in this specification. One example ofinstrumentation is described in Test Methods E 1082.1.4 The values stated in inch-pound units are to be regardedas the standard.1.5 The following caveat pertains only to Section 5 of thisspecification: This standard does not

    5、purport to address all ofthe safety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:

    6、E 1082 Test Method for Measurement of Vehicular Re-sponse to Traveled Surface Roughness2E 1136 Specification for a Radial Reference Test Tire22.2 Other Document:A4082 TPC Tire Performance Criteria, Procedures andSpecifications33. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 sp

    7、rung massthe total mass minus the unsprungmass.3.1.2 suspension deflectionthe change in the vertical dis-tance between the axle at its centerline and a hypotheticalreference line directly above the axle centerline on the rigidframe structure.4. Other Requirements4.1 Damping Ratio of Suspension Syste

    8、mThe dampingratio of the suspension system on the assembled trailer shall beevaluated by measuring the accumulated suspension movementon the trailer as it is towed over a known or standard calibrationtest surface. It must be verified that it meets one of theacceptance criteria.3The design requiremen

    9、ts for the shockabsorbers (5.1.1.3) may be used as an alternative to thisrequirement.4.2 Spring RateThe spring force constant (spring rate) ofthe assembled suspension shall be measured as follows:4.2.1 Apparatus:4.2.1.1 Dial Indicators, with a nominal accuracy of 0.001in. (0.025 mm). Two are require

    10、d.4.2.1.2 Loading Weights, permitting load increments ofapproximately 20 lbf (89 N) are required.4.2.2 ProcedureMeasure the vertical deflections of thesuspension by placing the dial indicators at points proximate tothe coil springs. With the trailer parked on a level surface,gently apply the weights

    11、, in approximately 20-lbf (89-N)increments, on the longitudinal centerline of the trailer directlyabove the centerline of the axle while recording the suspensiondeflection values observed on each dial indicator. Take care notto jar the trailer when applying the weights. Once all theweights have been

    12、 applied up to the total mass, remove them inthe same manner while recording the deflection measurementsat each increment.4.2.3 Data ReductionSeparately plot the load-deflectionvalues for each suspension system (left and right) on rectilineargraph paper. Draw a straight line that best reflects the s

    13、lope ofthe upward (loading) and downward (unloading) data points,ignoring the initial data point if necessary. The slope of thatline is the spring rate and must fall within the range of 180 to220 lbf/in. (32 to 39 N/mm).4.3 Legal Requirements:1This specification is under the jurisdiction of ASTM Com

    14、mittee E17 onVehicle-Pavement Systems and is the direct responsibility of Subcommittee E17.31on Methods for Measuring Profile and Roughness.Current edition approved July 15, 1993. Published November 1993. Originallyapproved in 1987. Last previous edition approved in 1990 as E 1215 90.2Annual Book of

    15、 ASTM Standards, Vol 04.03.3Available from General Motors Engineering Staff, GM Proving Ground,Milford, MI 48042.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.4.3.1 The vehicle and trailer shall comply with all appli-cable state an

    16、d federal laws, including those related to hitchconnections and lighting of towed vehicles.4.3.2 Reasonable precautions shall be taken beyond thoseimposed by laws and regulations to ensure maximum safety ofoperating personnel and other traffic.5. Design Requirements5.1 ChassisThe chassis shall consi

    17、st of a rigid framesuspension, two wheels mounted on a rigid axle, and a towhitch.5.1.1 Suspension SystemThe trailer frame shall be sus-pended on the axle by a system that includes the followingcomponents:5.1.1.1 Horizontal Linkages shall separately constrain theaxle in the longitudinal and lateral

    18、directions while allowingfree vertical excursion.5.1.1.2 SpringsTwo coil springs connecting the axle andframe, shall be mounted vertically over the centerline of theaxle. The force constant of each spring shall be 200 6 20lbf/in. (3506 35 N/mm or m). The springs shall be equidistantfrom the longitud

    19、inal centerline of the trailer at a distance notless than 15 in. (0.38 m).5.1.1.3 Shock AbsorbersTwo shock absorbers, mountedvertically from the axle to the trailer frame, shall be equidistantfrom the longitudinal centerline of the trailer. The ratios of theshock absorbers damping value over12 the s

    20、prung mass(2C/MS) shall be in the range of 5.5 to 13 s1with a mean valueof8s1.4The performance requirement for the damping rate ofthe suspension system in 4.1 may be used as an alternative tothis requirement.5.1.2 Axle and WheelsThe trailer shall have a two-wheelrigid axle in accordance with the fol

    21、lowing requirements:5.1.2.1 WheelsThe wheels shall be 15 by 6 in. rims.Radial run-out at the bead seats of the wheels when installed onthe axle shall be less than 0.01 in. (0.25 mm) peak-to-peak. Therim shall be marked to indicate the “low-point for matchingwith the tire. The low-point is establishe

    22、d by determining thepoints of minimum radius on each bead seat and locating thelow-point intermediately between those points in proportion totheir relative magnitudes.5.1.2.2 TiresThe tires shall be size P215/75R15, orequivalent, or Specification E 1136, and shall meet the GMTPC Specification.3Befor

    23、e operation, set the tire inflationpressure at the tire manufacturers maximum recommendedpressure for size and type of tire used at ambient temperature.5.1.2.3 Optional AlternativeIf the equipment given in4.2.1 is used, the dial indicators are placed close to the tires tomeasure axle-to-road displac

    24、ement. The tire pressure is ad-justed to give a116 in. (1.6 mm) vertical displacement when200 lbf (890 N) is used rather than the manufacturersmaximum recommended pressure.5.1.2.4 Tire-Wheel AssemblyThe tires shall be mountedon the wheels so that the painted dot indicating peak tire runoutreaches th

    25、e low-point mark on the wheel. The tire-wheelassemblies shall be balanced within 8.0 in./oz (0.58 cm/kg).5.1.2.5 Wheel TrackThe lateral distance between the cen-ter planes of the two tires shall be 68 6 5 in. (1.73 6 0.13 m).5.1.3 Tow HitchA ball-type hitch receptacle shall bemounted at the forward

    26、end of the frame on the longitudinalcenterline of the trailer.NOTE 1The towing vehicle must have power enough to pull the trailerat whatever uniform velocity is specified, even up 6 % grades, and mustbe in good operating condition, particularly its shock absorbers.5.1.3.1 WheelbaseThe trailer shall

    27、be designed so that thelongitudinal distance between the center of the ball-hitch andthe centerline of the axle shall be 120 6 1 in. (3.05 6 0.03 m).5.1.4 Total MassThe mass of the fully assembled trailershall be 1660 6 50 lbm (753 6 23 kg), and it shall bedistributed so that the ground load at each

    28、 of the wheels will be780 6 20 lbf (3470 6 89 N), and the hitch load shall be 1006 10 lbf (445 6 44 N). The center of percussion in the verticalplane shall be located as near to the axle as possible.5.1.5 Unsprung MassThe total mass of the axle, wheels,and tires, together with that of the suspension

    29、 system, shall be320 6 30 lbm (145 6 14 kg).5.1.6 Sprung Massshall normally be 1340 lbm (608 kg).NOTE 2The ratio of the unsprung mass to the sprung mass (Mu/Ms)ishigher than many automobiles.ASTM International takes no position respecting the validity of any patent rights asserted in connection with

    30、 any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible techni

    31、cal committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideratio

    32、n at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harb

    33、or Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).4Supporting data have been filed at ASTM International Headquarters and maybe obtained by requesting Research Report RR: E-17-1002.E 1215 93 (2003)2


    注意事项

    本文(ASTM E1215-1993(2003) Standard Specification for Trailers Used for Measuring Vehicular Response to Road Roughness《测量车辆对道路粗糙度的行车响应用挂车》.pdf)为本站会员(cleanass300)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开