欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM D6753 D6753M-2002(2009) 346 Standard Specification for Coal Tar Adhesive《煤焦油胶粘剂标准规范》.pdf

    • 资源ID:523464       资源大小:59.44KB        全文页数:2页
    • 资源格式: PDF        下载积分:5000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要5000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM D6753 D6753M-2002(2009) 346 Standard Specification for Coal Tar Adhesive《煤焦油胶粘剂标准规范》.pdf

    1、Designation: D 6753/D 6753M 02 (Reapproved 2009)Standard Specification forCoal Tar Adhesive1This standard is issued under the fixed designation D 6753/D 6753M; the number immediately following the designation indicates theyear of original adoption or, in the case of revision, the year of last revisi

    2、on. A number in parentheses indicates the year of lastreapproval. A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers coal tar adhesive with orwithout polymer modification suitable for brush, spray, squee-gee and trowel a

    3、pplication to coal tar built up and coal tarmodified bitumen membrane roofings and flashings.1.2 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard. The values stated ineach system may not be exact equivalents; therefore, eachsystem shall be used indepe

    4、ndently of the other. Combiningvalues from the two systems may result in non-conformancewith the standard.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety an

    5、d health practices and determine the applica-bility of regulatory requirements prior to use.2. Referenced Documents2.1 ASTM Standards:2D 903 Test Method for Peel or Stripping Strength of Adhe-sive BondsD 6511 Test Methods for Solvent Bearing BituminousCompounds3. Classification3.1 Type IBrush, squee

    6、gee, or spray consistency intendedfor use in the application of field sheet membranes.3.2 Type IIHeavy brushing or trowel consistency intendedfor use in the repair of coal tar roofing and flashings andinstallation of flashings.4. Materials and Manufacture4.1 Coal tar adhesive shall consist of a proc

    7、essed coal tarbase, volatile solvents, mineral stabilizers, with or withoutpolymer modifiers excluding asbestos, mixed to a smoothconsistency.5. Physical Requirements5.1 The material shall conform to the requirements pre-scribed in Table 1.5.2 UniformityA thoroughly stirred sample shall show nosepar

    8、ation of solvent or settling that cannot be overcome bymoderate stirring after standing for 72 h at room temperature ina closed container.6. Sampling and Test Methods6.1 Test Methods D 6511:6.2 Strength of LapTest Methods D 6511 as modifiedbelow:6.2.1 Three sets of four specimens shall be prepared,

    9、con-ditioned, and tested at three different temperatures for lap shearstrength.6.2.2 Temperatures are to be 10, 25, and 60C 50, 77, and140F, for conditioning and 10, 25, and 32C 50, 77, and90F for testing. Preparation of specimens shall be done at alaboratory temperature of 23 6 1.8C 73.4 6 3.6F.6.2

    10、.3 Test Specimen and Sample:6.2.3.1 Use a sample of the actual roofing membraneintended for use with the adhesive.6.2.3.2 For each specimen, cut a 1- by 12-in. 25- by305-mm transverse strip of membrane that includes theselvage; then cut this strip in half so that one piece contains theselvage and th

    11、e other is plain.6.2.3.3 Spread the amount of coal tar adhesive recom-mended by the manufacturer evenly over the selvage and thenplace the reverse side of the plain half over the adhesive coatedselvage in the same manner as a field lap would be made.6.2.3.4 Place a 10-lb 4.5-kg mass over the lap. Th

    12、e massshall be large enough to cover the area containing adhesive.After 2 min, remove the mass and condition the specimens asprescribed in Table 1. Use care when handling or movingsamples.6.2.4 ProcedureTest each specimen immediately after thespecified conditioning period in accordance with Test Met

    13、hodsD 6511. If any specimen fails to meet the minimum valuesspecified in Table 1, report the material as failing the lapstrength.6.3 Peel Strength:6.3.1 Test each specimen immediately after the specifiedconditioning period in accordance with Test Method D 903.Specimens prepared as in 6.2.3. If any s

    14、pecimen fails to meet1This specification is under the jurisdiction of ASTM Committee D08 onRoofing and Waterproofing and is the direct responsibility of Subcommittee D08.05on Solvent-Bearing Bituminous Compounds for Roofing and Waterproofing.Current edition approved July 1, 2009. Published July 2009

    15、. Originally approvedin 2002. Last previous edition approved in 2008 as D 6753 02(2008).2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summa

    16、ry page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.the minimum values specified in Table 1, report the material asfailing the peel strength.7. Inspection7.1 Inspection of the material shall be as agreed uponbe

    17、tween the purchaser and the suppler as part of the purchasecontract.8. Rejection and Resubmittal8.1 Failure to conform to any of the requirements prescribedin this specification may constitute grounds for rejection. In thecase of rejection, the seller shall have the right to reinspect therejected ma

    18、terial and resubmit the lot after removal of thosepackages not conforming to the requirements.9. Packaging and Package Marking9.1 Unless otherwise agreed upon, all products shall bepackaged and labeled in accordance with applicable regula-tions. Each package shall be marked to indicate the applicabl

    19、etype and ASTM specification.10. Keywords10.1 adhesive; coal tar; peel strength; shear strengthASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determina

    20、tion of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or with

    21、drawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that you

    22、r comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (sing

    23、le or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).TABLE 1 Requirements for Coal Tar AdhesiveAType I Type IINon-volatile matter, % min 73

    24、 60Water, % max. 2.0 3Ash (% of nonvolatile matter), min. 4 12Lap shear strength, min, kN/m 24 h 72 h 7 days 28 days 24 h 72 h 7 days 28 daysConditioned and tested at 10C 50F 25 60 MFBMF 60 65 MF MFConditioned and tested at 25C 77F 15 40 70 MF 70 75 MF MFConditioned at 60C 140F and tested at 32C 90F

    25、 6 15 20 MF 25 30 MF MFPeel strength min, kN/m 24 h 72 h 7 days 28 days 24 h 72 h 7 days 28 daysConditioned and tested at 10C 50F 0.25 0.45 0.81 1.75 0.50 0.70 2.80 2.90Conditioned and tested at 25C 77F 0.20 0.50 0.95 2.50 0.80 2.0 5.50 7.0Conditioned at 60C 140F and tested at 32C 90F 0.40 1.36 2.0 2.10 2.40 2.50 2.80 3.00AValues in table developed with a coal tar modified bitumen sheet adhered to itself.BMF denotes substrate failure.D 6753/D 6753M 02 (2009)2


    注意事项

    本文(ASTM D6753 D6753M-2002(2009) 346 Standard Specification for Coal Tar Adhesive《煤焦油胶粘剂标准规范》.pdf)为本站会员(figureissue185)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开