欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM D6607-2000(2009) 8750 Standard Practice for Inclusion of Precision Statement Variation in Specification Limits《在规范限定内严密语句变更范围的标准实施规程》.pdf

    • 资源ID:523029       资源大小:74.72KB        全文页数:3页
    • 资源格式: PDF        下载积分:5000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要5000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM D6607-2000(2009) 8750 Standard Practice for Inclusion of Precision Statement Variation in Specification Limits《在规范限定内严密语句变更范围的标准实施规程》.pdf

    1、Designation: D6607 00 (Reapproved 2009)Standard Practice forInclusion of Precision Statement Variation in SpecificationLimits1This standard is issued under the fixed designation D6607; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision

    2、, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice covers a method of determining rationalspecification limits by inclusion of the precision

    3、of the testmethod used in the specification.1.2 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of

    4、 the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2C670 Practice for Preparing Precision and Bias Statementsfor Test Methods for Construction MaterialsC802

    5、 Practice for Conducting an Interlaboratory Test Pro-gram to Determine the Precision of Test Methods forConstruction MaterialsD2172 Test Methods for Quantitative Extraction of Bitu-men From Bituminous Paving MixturesD2726 Test Method for Bulk Specific Gravity and Densityof Non-Absorptive Compacted B

    6、ituminous MixturesE177 Practice for Use of the Terms Precision and Bias inASTM Test Methods2.2 Federal Highway Administration Report:FHWA Report HI-93047 Materials Control andAcceptanceQuality Assurance, Federal Highway Ad-ministration, May 199333. Terminology3.1 For definitions of terms used in thi

    7、s practice, consultPractice E177.4. Significance and Use4.1 Each test method has a limited precision. Even if a testis performed as carefully and as correctly as possible on amaterial which is as homogeneous as can be obtained, the testwill still vary from one to another. A widely used measure ofthe

    8、 variation of the test results from a test method is thestandard deviation (s). In an ASTM standard test, the standarddeviation of the test method can be found in the Precision andBias statement for the test. The “Blue Book,” Form and Stylefor ASTM Standards, requires that all test methods includePr

    9、ecision and Bias statements. Practice C670 and PracticeC802 provide guidance for determination of these values.4.2 If the precision of a test method is low and the precisionof the test has not been properly considered in a materialspecification, a uniform material with the right quality may stillbe

    10、rejected most of the time because of the wide variation ofthe test results. In order to have rational specification limits, theprecision of the test used should be properly included in aspecification.4.3 This practice provides a guideline for proper inclusionof precision of the test method in a rati

    11、onal specification.5. Procedure5.1 Determine the effective standard deviation (sX)ofthetest results due to the combined effects of materials variationand test variation using Eq 1:sX5 sM21sT2! (1)1This guide is under the jurisdiction of Committee D04 on Road and PavingMaterials and is the direct res

    12、ponsibility of Subcommittee D04.94 on StatisticalProcedures and Evaluation of Data.Current edition approved Dec. 1, 2009. Published January 2010. Originallyapproved in 2000. Last previous edition approved in 2005 as D6607 00 (2005).DOI: 10.1520/D6607-00R09.2For referenced ASTM standards, visit the A

    13、STM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from National Technical Information Service (NTIS), U.S. Depart-ment of Commerce, 5285 Port R

    14、oyal Rd., Springfield, VA 22161.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.where:sM= standard deviation of test property due to materialvariation (see Note 1), andsT= standard deviation of test property due to test method(see No

    15、te 2).NOTE 1sMis the expected standard deviation of the material propertywhen the material is produced in a properly controlled process.Astandarddeviation which is representative of the acceptable variation of thematerial can be used. It can be calculated from the data obtained fromproperly produced

    16、 materials.NOTE 2sTis the standard deviation as given in the precisionstatement for the test method used to measure the test property.5.2 Determine the standard deviation of the mean of the testresults (s3) using Eq 2:s35s3/ =n (2)where:n = number of tests performed.5.3 For a two-ended specification

    17、 (with both a minimumand maximum limits), the specification limits for the averagetest value from n test ( x ) should be the following: Za /2s3# 3 # 1 Za /2s3(3)where: = target propertyZa/2= critical number of standard deviations for (1a)confidence interval. (See Table 1 for values of Za /2 for diff

    18、erent specified confidence intervals.)5.4 For a one-ended specification (with only a maximum orminimum limit), the specification limit for the average testvalue from n test ( x ) should be the following:3 $ Zas3with a minimum limit! (4)or3 # 1 Zas3with a maximum limit! (5)APPENDIXESX1. First Example

    19、 of the Application of Precision Limits to Specification WritingX1.1 Problem StatementX1.1.1 A specification is to be written for the asphaltcontent of an asphalt mixture with aggregate water absorptioncapacity of less than 1.25 %. Three reflux asphalt extractiontests are to be run and the average o

    20、f three test results is to beused for acceptance purpose. The target asphalt content is6.2 %. It is assumed that the contractor can reasonably controlthe asphalt content with a standard deviation of 0.20 % (seeNote X1.1).NOTE X1.1Typical standard deviations of different material proper-ties can be f

    21、ound in FHWA Report HI-93047. The typical range ofstandard deviation of asphalt content was given as 0.15 % 0.30 %.X1.2 Precision statement for Test Methods D2172 (MethodBReflux) is given in Table X1.1.X1.3 The combined standard deviation of the measuredasphalt content:sx5 = 0.221 0.232! 5 0.305 % (

    22、X1.1)X1.4 The standard deviation of the mean of three testresults:sx5 0.305 / = 3 5 0.176 % (X1.2)X1.5 Specification limits using a 95 % confidence interval:5 6.2 % 6 Za/20.176 %!5 6.2 % 6 1.96 0.176 %!5 6.2 % 6 0.3 % (X1.3)X2. Second ExampleX2.1 Problem StatementX2.1.1 A specification is to be writ

    23、ten for the asphaltcontent of the asphalt mixture as described in Example 1.However, the average of seven test results (instead of three testresults) is to be used.X2.2 The combined standard deviation of the measuredasphalt content is the same as in Example 1:sx5 = 0.221 0.232! 5 0.305 % (X2.1)X2.3

    24、The standard deviation of the mean of seven testresults:sx5 0.305 / = 75 0.115 % (X2.2)TABLE 1 Z Values for Different Confidence LevelsConfidence Level (1 a): 90 % 95 % 97.5 % 99.0 %Za/2(Two-End Specification) 1.645 1.960 2.243 2.575Za(One-End Specification) 1.282 1.645 1.960 2.327TABLE X1.1 Mixes w

    25、ith Agg. of Water Absorption 1.25 %StandardDeviationAcceptable Range ofTwo Test ResultsSingle-Operator 0.19 % .054 %Multi-Operator 0.23 % 0.65 %D6607 00 (2009)2X2.4 Specification limits using a 95 % confidence interval:5 6.2 % 6 1.96 0.115 %!5 6.2 % 6 0.2 % (X2.3)X3. Third ExampleX3.1 Problem Statem

    26、entX3.1.1 A specification is to be written for the compacteddensity of an asphalt mixture with non-absorptive aggregate.The target density is 2.365 g/cm3. Five density measurementsin accordance with Test Method D2726 are to be made, and theaverage test result is to be used for acceptance purposes. I

    27、t isassumed that the contractor can control the density of themixture with a standard deviation of 0.02 g/cm3.X3.2 Precision statement for Test Method D2726 is inTable X3.1.X3.3 The combined standard deviation of the measureddensity:sx5 = 0.20021 0.02692!5 0.0335 g/cm3(X3.1)X3.4 The standard deviati

    28、on of the mean of five test results:sx5 0.0335 / = 5!5 0.0150 g/cm3(X3.2)X3.5 Specification limit using a 95 % confidence interval:Minimum average measured density5 2.365 Za0.015!5 2.365 1.65 0.115!35 2.340 g/cm (X3.3)X3.6 With this specification, a contractor who compacts theasphalt mixture to an a

    29、verage density of 2.356 g/cm3wouldmeet the specification 95 % of the time.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity

    30、of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments

    31、are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not r

    32、eceived a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies

    33、) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).TABLE X3.1 Precision Statement ValuesStandardDeviationAcceptable Range ofTwo Test ResultsSingle-Operator Precision 0.0124 0.035Multi-Operator Precision 0.0269 0.076D6607 00 (2009)3


    注意事项

    本文(ASTM D6607-2000(2009) 8750 Standard Practice for Inclusion of Precision Statement Variation in Specification Limits《在规范限定内严密语句变更范围的标准实施规程》.pdf)为本站会员(boatfragile160)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开