欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM D6601-2002(2008) 431 Standard Test Method for Rubber Properties&x2014 Measurement of Cure and After-Cure Dynamic Properties Using a Rotorless Shear Rheometer《用无转子剪切流变仪测量橡胶在固化和.pdf

    • 资源ID:523005       资源大小:88.34KB        全文页数:4页
    • 资源格式: PDF        下载积分:5000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要5000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM D6601-2002(2008) 431 Standard Test Method for Rubber Properties&x2014 Measurement of Cure and After-Cure Dynamic Properties Using a Rotorless Shear Rheometer《用无转子剪切流变仪测量橡胶在固化和.pdf

    1、Designation: D 6601 02 (Reapproved 2008)Standard Test Method forRubber PropertiesMeasurement of Cure and After-CureDynamic Properties Using a Rotorless Shear Rheometer1This standard is issued under the fixed designation D 6601; the number immediately following the designation indicates the year ofor

    2、iginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the use of a rotorless oscillatingshe

    3、ar rheometer for measuring after cure dynamic properties atpredetermined temperature(s) below the cure temperature.1.2 Specified cure conditions that approximate a “staticcure” also are covered to minimize effects on cured rubbercompound dynamic properties. This test method is not in-tended to repla

    4、ce Test Method D 5289.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior

    5、to use.1.4 WarningCompounds based on silicone or fluoroelas-tomers may have high levels of thermal contraction or pooradhesion to the dies when cooled after the cure portion of thistest method, causing slippage during strain sweeps. If thisoccurs, the results will not be reliable.2. Referenced Docum

    6、ents2.1 ASTM Standards:2D 1349 Practice for RubberStandard Temperatures forTestingD 4483 Practice for Evaluating Precision for Test MethodStandards in the Rubber and Carbon Black ManufacturingIndustriesD 5289 Test Method for Rubber PropertyVulcanizationUsing Rotorless Cure MetersD 5992 Guide for Dyn

    7、amic Testing of Vulcanized Rubberand Rubber-Like Materials Using Vibratory Methods3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 complex shear modulus, G*, nthe ratio of peakamplitude shear stress to peak amplitude shear strain; math-ematically, G* =(G82+ G92)1/2.3.1.2 comple

    8、x torque, S*, nthe peak amplitude torqueresponse measured by a reaction torque transducer for asinusoidally applied strain; mathematically, S* is computed byS* =(S82+ S92)1/2.3.1.3 dynamic cure, nany cure condition which oscillatesor moves the die.3.1.4 elastic torque, S8, nthe peak amplitude torque

    9、 com-ponent, which is in phase with a sinusoidally applied strain.3.1.5 loss angle, d, nthe phase angle by which thecomplex torque (S*) leads a sinusoidally applied strain.3.1.6 loss factor, tan d, nthe ratio of loss modulus tostorage modulus, or the ratio of viscous torque to elastictorque; mathema

    10、tically, tan d = G9/G8 =S9/S8.3.1.7 loss shear modulus, G9, nthe component of appliedstress that is 90 out-of-phase with the shear strain, divided bythe strain.3.1.8 static cure, nthe cure conditions of 0.0 arc strainand 0.0 Hz in frequency, that is, no movement of the diesduring the cure test.3.1.9

    11、 storage shear modulus, G8, nthe component ofapplied stress that is in phase with the shear strain, divided bythe strain.3.1.10 viscous torque, S9, nthe peak amplitude torquecomponent, which is 90 out of phase with a sinusoidallyapplied strain.4. Summary of Test Method4.1 A rubber test specimen is c

    12、ontained in a die cavity thatis closed and maintained at an elevated cure temperature. Thecavity is formed by two dies, one of which is oscillated througha rotary amplitude. This action produces a sinusoidal torsionalstrain in the test specimen resulting in a sinusoidal torque,which measures the vis

    13、coelastic changes of the test specimenas it cures. The test specimen must be a unvulcanized rubber1This test method is under the jurisdiction of ASTM Committee D11 on Rubberand is the direct responsibility of Subcommittee D11.14 on Time and Temperature-Dependent Physical Properties.Current edition a

    14、pproved May 1, 2008. Published June 2008. Originallyapproved in 2000. Last previous edition approved in 2002 as D 6601 02.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, ref

    15、er to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United Spound containing curatives. A controlled limited strain isapplied during cure to prevent effecting the aftercure proper-ties.4.2 A

    16、fter a predetermined cure time, the temperature isreduced and dynamic property measurements can be based ona strain sweep in which the strain amplitude is programmed tochange in steps under constant frequency and temperature, afrequency sweep in which the frequency is programmed tochange in steps un

    17、der constant strain amplitude and tempera-ture, or, a temperature sweep in which the temperature isprogrammed to decrease under constant strain amplitude andfrequency conditions.4.3 For an after-cure strain sweep, the instrument is typi-cally programmed to increase the strain with each subsequentste

    18、p change. This is done to minimize the influence of prior testconditions on subsequent test steps. Typically two repeat strainsweeps may be programmed consecutively to quantify thePayne Effect,3which is the reduction in dynamic storagemodulus from strain softening of the rubber vulcanizate.5. Signif

    19、icance and Use5.1 This test method is used to determine the vulcanizationcharacteristics of (vulcanizable) rubber compounds under se-lected test conditions of strain and frequency which do notsignificantly affect the cured dynamic properties. In the sametest, this test method also will measure the d

    20、ynamic propertiesof the vulcanizate at temperatures significantly below the curetemperature. These lower temperature measurements are nec-essary in order to more effectively relate to rubber productservice conditions.5.2 This test method may be used for quality control inrubber manufacturing process

    21、es and for research and develop-ment testing of rubber compounds containing curatives. Thistest method also may be used for evaluating cure and dynamicproperty differences resulting from the use of different com-pounding ingredients.5.3 For additional information regarding the significance ofdynamic

    22、 testing of vulcanized rubber, the reader may wish toreference Guide D 5992.6. Apparatus6.1 Torsion Strain Rotorless Oscillating Rheometer with aSealed CavityThis type of rheometer measures the elastictorque S8 and viscous torque S9 produced by oscillating angularstrain of set amplitude and frequenc

    23、y in a completely closedand sealed test cavity.6.2 Sealed Die CavityThe sealed die cavity is formed bytwo conical surface dies. In the measuring position, the twodies are fixed a specified distance apart so that the cavity isclosed and sealed (see Fig. 1).6.3 Die GapFor the sealed cavity, no gap sho

    24、uld exist atthe edges of the dies. At the center of the dies, the die gap shallbe set at 0.45 6 0.05 mm.6.4 Die Closing MechanismFor the sealed cavity, a pneu-matic cylinder or other device shall close the dies and holdthem closed during the test with a force not less than 11 kN(2500 lbf).6.5 Die Os

    25、cillating SystemThe die oscillating systemconsists of a direct drive motor, which imparts a torsionaloscillating movement to the lower die in the cavity plane.6.5.1 The oscillation amplitude can be varied, but a selec-tion of 0.2 arc (62.8 % shear strain) is preferred for the curetest while strains

    26、from 61to6100 % are preferred for theafter-cure strain sweeps. The oscillation frequency can bevaried between 0.03 Hz and 30 Hz.6.6 Torque Measuring SystemThe torque measuring sys-tem shall measure the resultant shear torque.6.6.1 The torque measuring device shall be rigidly coupledto the upper die,

    27、 any deformation between the die and deviceshall be negligibly small, and the device shall generate a signal,which is proportional to the torque. The total error resultingfrom zero point error, sensitivity error, linearity, and repeat-ability errors shall not exceed 1 % of the selected measuringrang

    28、e.6.6.2 The torque recording device shall be used to record thesignal from the torque measuring device and shall have aresponse time for full scale deflection of the torque scale of 13A.R. Payne, J. Polymer Sci., 6, 57 (1962).FIG. 1 Typical Sealed Torsion Shear Rotorless CuremeterD 6601 02 (2008)2s

    29、or less. The torque shall be recorded with an accuracy of 60.5 % of the range. Torque recording devices may includeanalog chart recorders, printers, plotters, or computers.6.6.3 A reference torque device is required to calibrate thetorque measurement system. A torque standard may be used tocalibrate

    30、 the torque measuring system at the selected angulardisplacement by clamping a steel torsion rod to the oscillatingand the torque measuring dies of the torsion shear rheometer(see Fig. 2). The reference values for angular displacement andcorresponding torque shall be established by the manufacturerf

    31、or each torque standard.6.7 Reference Test TemperatureThe standard referencetest temperature for cure shall be either 140C, 160C, or180C while dynamic property measurements after-cure (dy-namic property measurements made after completion of thecure test) should be made at either 100C or 60C. Tests m

    32、aybe carried out at other temperatures, if required. Other tem-peratures should be selected in accordance with PracticeD 1349 when practical.6.8 Temperature Control SystemThis system shall permitthe reference temperature to be varied between 40C and220C with an accuracy of 60.3C or better.6.8.1 The

    33、dies shall heat to the set point temperature in 1.0min or less from closure of the test cavity. Once the initialheating up time has been completed, die temperature shall notvary by more than 60.3C for the remainder of a cure test ata set temperature. When the set temperature is changed in aprogramme

    34、d temperature sweep or strain sweep, dynamicproperty measurements should not be recorded until the dietemperatures are within 60.3C of the new set temperature forat least 30 s.6.8.2 Temperature distribution within the test piece shall beas uniform as possible. Within the deformation zone, a toler-an

    35、ce of 61C of the average test piece temperature shall not beexceeded.6.8.3 Die temperature is determined by a temperature sensorused for control. The difference between the die temperatureand the average test piece temperature shall not be more than2C. Temperature measurement accuracy shall be 60.3C

    36、 forthe die temperature sensor.6.8.4 The upper and lower dies shall each be jacketed withforced air cooling devices in order to rapidly decrease thetemperature of the upper and lower dies after the cure test iscompleted.7. Test Specimen7.1 A test specimen taken from a sample shall be between 5and 6

    37、cm3for the sealed cavity oscillating rheometer. Thespecimen volume should exceed the test cavity volume by asmall amount, to be determined by preliminary tests. Typically,specimen volume should be 130 to 150 % of the test cavityvolume. Once a target mass for a desired volume has beenestablished, spe

    38、cimen masses should be controlled to within60.5 g for best repeatability. The initial test specimen shapeshould fit well within the perimeter of the test cavity.7.2 Compounded Rubber SpecimensTest specimens shallbe taken from a rubber compound as required by the mixingmethod or other sampling instru

    39、ctions. Only rubber com-pounds with curatives may be tested.7.2.1 The rubber compound shall be in the form of a sheet,at room temperature, and as free of air as possible.8. Procedure8.1 Select from one of six different cure conditions shown inTable 1.8.2 Select from one of eight different after-cure

    40、 dynamictesting conditions shown in Table 2.8.3 Program a test configuration which incorporates theseconditions and store on the instrument computer operatingsystem.8.4 Load the test configuration to run the test.8.5 Enter specimen identification.8.6 Wait until both dies are at the initial test temp

    41、erature.Open the test cavity and visually check both upper and lowerFIG. 2 Typical Torque Standard Calibration Device for TorsionShear CuremetersTABLE 1 Test Conditions for Cure TestANOTE 1Cure properties should be measured in accordance with TestMethod D 5289.Cure Condition No. Temperature, C Frequ

    42、ency, Hz Strain, 6 Arc.1 140 1.67 0.22 160 1.67 0.23 180 1.67 0.24 140 0 05 160 0 06 180 0 0APlease note that cure conditions of 0.2 arc strain and 1.67 Hz frequency mayinfluence post cure propertiesD 6601 02 (2008)3dies for cleanliness. Clean the dies, if necessary. Place the testspecimen on the ce

    43、nter of the lower die and close the dieswithin 20 s.9. Report9.1 Report the following information.9.1.1 Afull description of the sample, or test specimen(s), orboth, including their origin.9.1.2 Type and model of oscillating rheometer.9.1.3 The frequency, strain, temperature and time for thecure tes

    44、t (if no strain, indicate “static cure”).9.1.4 Minimum torque (ML) as dNm, maximum torque (MH)as dNm, time to scorch as indicated by time to one unit rise (indNm units) from minimum torque (tS1) in minutes and decimalfraction of a minute, and time to 10 %, 50 %, and 90 % state ofcure in minutes and

    45、decimal fraction of a minute.NOTE 1For static cure, no cure properties are reported since nomeasurements are possible.9.1.5 The temperature, frequency and different strains ap-plied in an after-cure strain sweep.9.1.6 The storage shear modulus G8 in kPa and the percentstrain for each step in the pro

    46、grammed strain sweep.9.1.7 The loss shear modulus G9 in kPa and the percentstrain for each step in the programmed strain sweep.9.1.8 The tangent delta (tan d) and the percent strain foreach step in the programmed strain sweep.9.1.9 If two consecutive strain sweeps are programmed, theresults from bot

    47、h of these strain sweeps should be recorded(reference the Payne Effect discussed in 4.3).10. Precision and Bias10.1 A precision and bias estimate has not been completedfor this test method at this time. This will be completed inaccordance with Practice D 4483.11. Keywords11.1 dynamic properties; los

    48、s modulus; rotorless oscillatingshear rheometer; storage modulusASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any suc

    49、h patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which


    注意事项

    本文(ASTM D6601-2002(2008) 431 Standard Test Method for Rubber Properties&x2014 Measurement of Cure and After-Cure Dynamic Properties Using a Rotorless Shear Rheometer《用无转子剪切流变仪测量橡胶在固化和.pdf)为本站会员(王申宇)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开