1、Designation: D6123/D6123M 97 (Reapproved 2012)Standard Specification forPressure-Sensitive Tape for Light-Duty Packaging andGeneral Purpose Masking1This standard is issued under the fixed designation D6123/D6123M; the number immediately following the designation indicates theyear of original adoptio
2、n or, in the case of revision, the year of last revision. A number in parentheses indicates the year of lastreapproval. A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers paper-backed pressure-sensitive tapes used for li
3、ght-duty packaging and masking.1.2 The values stated in either inch-pound or SI units are tobe regarded separately as standard. The values stated in eachsystem are not exact equivalents; therefore, each system mustbe used independently, without combining values in any way.1.3 The following safety ha
4、zards caveat pertains only to thetest methods portion, Section 13, of this specification. Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and
5、determine the applicability of regulatory limita-tions prior to use.2. Referenced Documents2.1 ASTM Standards:2D996 Terminology of Packaging and Distribution Environ-mentsD3121 Test Method for Tack of Pressure-Sensitive Adhe-sives by Rolling BallD3330/D3330M Test Method for Peel Adhesion ofPressure-
6、Sensitive TapeD3611 Practice forAcceleratedAging of Pressure-SensitiveTapesD3652/D3652M Test Method for Thickness of Pressure-Sensitive TapesD3715/D3715M Practice for Quality Assurance ofPressure-Sensitive TapesD3759/D3759M Test Method for Breaking Strength andElongation of Pressure-Sensitive TapeD3
7、951 Practice for Commercial PackagingD5486/D5486M Specification for Pressure-Sensitive Tapefor Packaging, Box Closure, and SealingD5570 Test Method for Water Resistance of Tape andAdhesives Used as Box Closure2.2 Federal Specification:PPP-T-680 Tape, Pressure-Sensitive: Packaging and Pack-ing of32.3
8、 ISO Standard:ISO 9002 Quality Systems Model for Quality Assurance inProduction and Installation43. Terminology3.1 DefinitionsGeneral definitions for packaging and dis-tribution environments are found in Terminology D996.4. Significance and Use4.1 The pressure-sensitive paper-backed tapes covered by
9、this specification are intended for packaging applications suchas bundling small parts to be overpacked, holding small partsto larger assemblies, and for temporary closure of chipboardboxes and fiberboard boxes that are not to be shipped bycommon carrier. They are also for general use applicationssu
10、ch as in temporarily masking surfaces from being covered bypaint, varnish, or other finishing materials. These tapes are notintended to be a substitute for tapes covered by SpecificationD5486/D5486M. Type I is for use where conformability isdesired. Type II is for uses requiring more strength and fo
11、rstraight line masking.5. Classification5.1 Type I is crepe paper backed.5.2 Type II is flat paper backed.6. Ordering Information6.1 The inquiry or order shall include the following:6.1.1 ASTM Designation and date of issue,6.1.2 Type required (see Section 5),6.1.3 Roll width and length (see Section
12、9),6.1.4 When testing and inspection certification is requiredand (see Section 16), and1This specification is under the jurisdiction of ASTM Committee D10 onPackaging and is the direct responsibility of Subcommittee D10.14 on Tape andLabels.Current edition approved April 1, 2012. Published May 2012.
13、 Originallyapproved in 1997. Last previous edition approved in 2007 as D6123/D6123M 97(2007). DOI: 10.1520/D6123_D6123M-97R12.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information,
14、 refer to the standards Document Summary page onthe ASTM website.3Available from Standardization Documents Order Desk, Bldg. 4, Section D,700 Robbins Ave., Phila., PA 191115094. Attn: NPODS.4Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, ht
15、tp:/www.ansi.org.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.6.1.5 Level of packaging and packing when other thancommercial (see Section 17).7. Materials and Manufacture7.1 The materials used in the construction of the tape shall
16、be such as to ensure conformance to the requirements of thisspecification.7.2 BackingThe paper backing shall be treated to make itresistant to water, paints, varnish and other finishing materials.The backing shall have sufficient strength to allow the tape tobe unwound from the roll and to be remove
17、d from the maskedsurface after application of finishing materials without break-age or delamination.7.3 AdhesiveThe adhesive shall be pressure-sensitive,water-insoluble, and shall require no moisture, heat, or otherpreparation prior to or after application to clean, dry surfaces.The adhesive shall b
18、e coated in a smooth and evenly distrib-uted layer on one side of the backing.7.4 RollsThe tape shall be evenly wound in rolls, adhe-sive side in, on cores made of paper-fiber or plastic. The coreshall have sufficient rigidity to prevent distortion under normalconditions of transportation and use. T
19、he inside diameter of thecore shall be 76.2 0 + 1.6 mm (3 0 +116 in.). When the rollis unwound, the backing shall not tear; the adhesive shall nottransfer nor split from the face of the tape backing to theadjacent layer before or after aging (see Table 1).8. Physical Properties8.1 The tape shall com
20、ply with the physical requirementslisted in Table 1 and the water-solubility requirement asdescribed in Test Method D5570.9. Dimensions, Mass, and Permissible Variations9.1 WidthThe width of the tape shall be12 in. or 12 mm;34 in. or 18 mm; 1 in. or 24 mm; 112 in. or 36 mm; 2 in. or 48mm or other co
21、mmercially available widths, as specified (see6.1.3). A width tolerance of 6132 in. or 0.75 mm shall beallowed on all widths.9.2 LengthThe length shall be 60 yd or 50 or 55 m orother commercially available lengths, as specified (see 6.1.3).9.3 SplicesThe roll shall consist of a single length of tape
22、,except that any single roll may contain a maximum of onesplice. A splice shall not separate when the roll is unwound byhand or machine.10. Workmanship10.1 The tape shall be constructed uniformly and be free ofdefects that impair its usefulness for the purpose intended (seeSection 4). The adhesive c
23、oating shall be a uniform coatingcovering one entire side of the tape. The edges shall be clean,straight, and unbroken. The rolls shall be wound evenly. Thefinished product shall conform to the levels of quality estab-lished herein.11. Sampling11.1 End Item ExaminationThe lot size for visual inspec-
24、tion shall be as specified in the end item inspection of 6.3 ofPractice D3715/D3715M. The sample unit shall be one roll.11.2 End Item TestingLot size and sampling for end itemtesting shall be as specified in end item testing of 6.4 ofPractice D3715/D3715M. The AQL shall be 4.0 %.12. Specimen Prepara
25、tion and Number of Tests12.1 Specimen preparation shall be as specified in theappropriate test method.12.2 Number of tests per unit of product shall be asspecified in the appropriate test method.12.3 First Article of ManufactureWhen a product is firstmanufactured in a plant, it shall be tested and i
26、nspected todetermine compliance with all examinations and tests of thisspecification. First article of manufacture examinations needonly be repeated when there is a change in materials, processes,or plant of manufacture. Specimens shall consist of at least fiverolls of tape representing a standard p
27、roduction lot.13. Test Methods13.1 Responsibility for InspectionUnless otherwise speci-fied in the contract or order, the manufacturer is responsible forthe performance of all inspection requirements as specifiedherein.13.2 Responsibility for ComplianceAll items must meetall requirements of Sections
28、 7-16. The inspections set forth inthis specification shall become part of the manufacturersoverall inspection system or quality program for the contract ororder. The absence of any inspection requirements in thespecification shall not relieve the manufacturer of the respon-sibility of ensuring that
29、 all products or supplies submitted foracceptance comply with all the requirements of the contract ororder. Sampling in quality conformance does not authorizesubmission of known defective material, either indicated oractual, nor does it commit the buyer to acceptance of defectivematerial.13.3 Classi
30、fication of Inspections:13.3.1 First Article of ManufactureWhen a product is firstmanufactured in a plant it shall be tested and inspected todetermine compliance with all examinations and tests of thisspecification by an independent laboratory. First article ofTABLE 1 PropertiesType I Type II TestAd
31、hesion 13.3.3Before oz/in., min 25 25aging N/100 mm, min 27 27After oz/in., min 20 20aging N/100 mn, min 22 22Tack (rolling ball), max 13.3.3in. 6 .mm 150 . . .Tensile lb/in., min 16 25 13.3.3N/100 mm, min 280 440Elongation, percent 13.3.3min 5 .max 15 . . .Thickness, in., max 0.009 0.009 13.3.3mm,
32、max 0.230 0.230D6123/D6123M 97 (2012)2manufacture examinations need only be repeated when there isa change in materials, processes or plant of manufacture.13.3.2 Quality Conformance InspectionsQuality confor-mance inspections shall consist of the following:Adhesion before agingTack (rolling ball)Ten
33、sile Strength13.3.3 The tests shall be conducted according to the follow-ing methods, as specified:Test MethodAccelerated aging (heat and humidity) Practice D3611Adhesion (initial and aged) Test Method A ofD3330/D3330MTensile and Elongation Test Method D3759/D3759MTack (rolling ball) Test Method D31
34、21Thickness Test Method D3652/D3652M14. Rejection and Rehearing14.1 Materials that fail to conform to the requirements ofthis specification may be rejected. Rejected material should bereported to the producer or supplier promptly and in writing.The producer or supplier may make claim for rehearing i
35、ncases of dissatisfaction with the results of any of the tests.15. Environmental Considerations15.1 Environmental ConsiderationsThe use of potentiallytoxic materials in the manufacture of tapes covered by thisspecification are of concern because of their presence inemissions should they be incinerat
36、ed or in leachate whenlandfilled. Materials used in the manufacture of tapes coveredby this specification shall not have any lead, cadmium,mercury, or hexavalent chromium intentionally introduced as acomponent during manufacture as opposed to the incidentalpresence of any of these elements.16. Certi
37、fication16.1 When specified (see 6.1.4) in the purchase order orcontract the manufacturer shall certify that the backing of thetapes is as specified (see 7.2).16.2 When specified (see 6.1.4) in the purchase order orcontract the purchaser shall be furnished a certification statingthat the sample roll
38、s representing each log of tape have beentested and inspected as directed in this specification, therequirements have been met and the tape has been produced ina manufacturing facility certified under ISO 9002.17. Preparation for Delivery17.1 Unless otherwise specified in the purchase order orcontra
39、ct, rolls of tape shall be packaged and packed inaccordance with Practice D3951. Such packing shall ensurearrival at the destination in a satisfactory condition and shall beacceptable to the carrier at the lowest rate.17.2 When specified (see 6.1.5), shipments to the U.S.Government shall be packaged
40、 and packed in accordance withPPP-T-680 at the levels specified in the purchase order orcontract.18. Keywords18.1 light duty; packaging; pressure-sensitive; tapeASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this sta
41、ndard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be revi
42、ewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsib
43、le technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Co
44、nshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).D6123/D6123M 97 (2012)3
