欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM D5617-2004 Standard Test Method for Multi-Axial Tension Test for Geosynthetics《土工合成织物多轴抗拉试验的标准试验方法》.pdf

    • 资源ID:520259       资源大小:78.09KB        全文页数:5页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM D5617-2004 Standard Test Method for Multi-Axial Tension Test for Geosynthetics《土工合成织物多轴抗拉试验的标准试验方法》.pdf

    1、Designation: D 5617 04Standard Test Method forMulti-Axial Tension Test for Geosynthetics1This standard is issued under the fixed designation D 5617; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A numbe

    2、r in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the measurement of the out-of-plane response of geosynthetics to a force that is appliedperpendicular to the initia

    3、l plane of the sample.1.2 When the geosynthetic deforms to a prescribed geomet-ric shape (arc of a sphere or ellipsoid) formulations areprovided to convert the test data to biaxial tensile stress-strainvalues. These formulations cannot be used for other geometricshapes. With other geometric shapes,

    4、comparative data ondeformation versus pressure is obtained.1.3 This test method is more commonly used to testgeomembranes. Permeable materials may also be tested inconjunction with an impermeable material.1.4 This test method requires a large diameter pressurevessel (600 mm). Information obtained fr

    5、om this test methodmay be more appropriate for design purposes than many smallscale index tests such as Test Method D 6693 or Test MethodD 7003.1.5 The values stated in SI units are to be regarded as thestandard. The inch-pound units given in parentheses are forinformation only.1.6 This standard doe

    6、s not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Stan

    7、dards:2D 4439 Terminology for GeotextilesD 6693 Test Method for Determining Tensile Properties ofNonreinforced Polyethylene and Nonreinforced FlexiblePolypropylene GeomembranesD 7003 Test Method for Strip Tensile Properties of Rein-forced Geomembranes3. Terminology3.1 Definitions:3.1.1 geosynthetic,

    8、 na planar product manufactured frompolymeric material used with soil, rock, earth, or other geo-technical engineering related material as an integral part of aman-made project, structure, or system.3.1.2 multi-axial tension, nstress in more than one direc-tion.3.1.3 For definitions of other terms u

    9、sed in this test method,refer to Terminology D 4439.4. Summary of Test Method4.1 A pre-cut geosynthetic sample is secured at the edges ofa large diameter (600 mm) pressure vessel. Pressure is appliedto the sample to cause out-of-plane deformation and failure.This deformation with pressure informatio

    10、n can then beanalyzed to evaluate various materials.5. Significance and Use5.1 Installed geosynthetics are subjected to forces frommore than one direction including forces perpendicular to thesurfaces of the geosynthetic. Out of plane deformation of ageosynthetic may be useful in evaluating material

    11、s for capswhere subsidence of the subsoil may be problematic.5.2 Failure mechanisms on this test may be different com-pared to other relatively small scale index tests and may bebeneficial for design purposes.5.3 In applications where local subsidence is expected, thistest can be considered a perfor

    12、mance test.NOTE 1Although, this test specifies a vessel size of 600 mm, largerdiameter vessels will better approximate field performance. However, theuser is cautioned that different size vessels may yield different results andhence may not be comparable.5.4 For applications where geosynthetics cann

    13、ot be de-formed in the fashion this test method prescribes, this testmethod should be considered an index test.5.5 Due to the time involved to perform this test method, itis not considered practical as a quality control test.1This test method is under the jurisdiction of ASTM Committee D35 onGeosynt

    14、hetics and is the direct responsibility of Subcommittee D35.10 on Geomem-branes.Current edition approved June 1, 2004. Published July 2004. Originally approvedin 1994. Last previous edition approved in 1999 as D561799e1.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact

    15、ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.6. Apparatus6.1 Fig. 1 sho

    16、ws an example of the test apparatus that can beused in the performance of this test method. The apparatusrequires a pressure vessel rated to a minimum of 690 kPa (100psi). The vessel diameter should be 600 mm3. Other sizevessels may be used but it is up to the user to establishcorrelation to the sta

    17、ndard size vessel.6.2 If the vessel has a deflection chamber it should notinhibit the geosynthetic from freely deflecting during the test.The deflection chamber shall be vented.6.2.1 Some materials will expand laterally beyond thediameter of the pressure vessel and may contact the sides of thedeflec

    18、tion chamber. In these cases, the test is no longer validand a different device must be used. Devices without deflectionchambers have worked well in these situations.6.3 The vessel will have a system to measure pressure andthe magnitude of central deflection.6.3.1 The system for measuring deflection

    19、 shall be capableof being read to an accuracy of 5 mm.6.3.2 The system for measuring pressure shall be capable ofbeing read to an accuracy of 3.5 kPa.6.4 All test shall be conducted at standard laboratory tem-peratures of 23 6 2C.7. Test Specimen7.1 Do not use test specimens with defects or any othe

    20、rabnormalities, unless this is the item of interest.7.2 Cut the test specimen larger than the area of the mainsealing force of the vessel.7.3 If a permeable material such as a geotextile is beingtested, an impermeable material such as a geomembrane or thinplastic sheet has to overlay the permeable m

    21、aterial to maintainthe pressure in the vessel during the test.7.3.1 When testing permeable materials, the impermeablematerial shall be more elastic than the permeable material(unless the combination of the two materials is the desired testvariable). This is required so that the permeable material fa

    22、ilsfirst.7.3.2 Test results on permeable materials will be affected bythe impermeable material used in the test.7.4 Test three replicate specimens on each sample unlessotherwise noted.8. Procedure8.1 Cut the test specimen to the requirements of the testvessel to ensure a good seal. Place specimen ac

    23、ross the openingof the vessel. Be sure the specimen is not sagging.8.2 Be sure the specimen remains flat while the edge of thespecimen is being securely clamped into place.8.3 Either air or water can be used to pressureize the vessel.If a water system is used, introduce water into the vessel untilit

    24、 is completely filled.8.4 Add water or air into the system so as to control the rateof centerpoint deflection at 20 mm/min in a continuous fashion.8.4.1 Stepwise increments of center point deflection are notallowed.8.5 Record the amount of centerpoint deflection and pres-sure at least every 10 s.8.6

    25、 Continue with the test by maintaining a constant rate ofcenterpoint deflection at the specified rate until the specimenhas ruptured (as noted by a sudden loss in pressure) or untilsome predetermined end point has been reached.NOTE 2The user is cautioned that the sudden release of pressure atrupture

    26、 could potentially be dangerous and cause either personal injury ordamage to the surroundings.8.7 Repeat the above with two additional specimens fromthe same sample.NOTE 3If the specimen has deformed in a fashion so that the surfaceof the specimen approximates an arc of a sphere or an ellipsoid,stre

    27、es-strain calculations are provided in the appendix.9. Report9.1 Report the following information:9.1.1 Sample identification,9.1.2 Size of vessel used (inside diameter), if other thanstandard,9.1.3 Conditions under which the test was performed, ifother than standard,9.1.3.1 For permeable membranes,

    28、 identify the imperme-able material used during the test including the thickness.NOTE 4The impermeable material may have a significant impact onthe data and must be considered when reviewing stress-strain results.9.1.4 Description of the failure and the shape of the speci-men after failure.9.1.5 Plo

    29、t the full pressure-deflection or stress-strain curvesfor all specimens.9.1.6 Average and individual specimen results for gauge,pressure at rupture and centerpoint deflection at rupture. Reportstress and strain at rupture if calculations were made.3The sole source of supply of the apparatus known to

    30、 the committee at this timeis BT Technology. If you are aware of alternative suppliers, please provide thisinformation to ASTM Headquarters. Your comments will receive careful consider-ation at a meeting of the responsible technical committee, which you may attend.FIG. 1 Multi-Axial Burst ApparatusD

    31、561704210. Precision and Bias10.1 The precision and bias of this test method have not yetbeen established.11. Keywords11.1 deformation; geosynthetics; multi-axialAPPENDIXES(Nonmandatory Information)X1. DESCRIPTION OF SAMPLE FAILURESX1.1 Materials will generally fail in a given manner thatcan be desc

    32、ribed by the following categories:X1.2 Failure Location:X1.2.1 Edge Tear (ET) Failure adjacent to the clampingring. May not represent the performance of the sample mate-rial.X1.2.2 Non-edge Failure (N-EF)A rupture sufficiently farenough away from the edge of the device to assume that thedevice did n

    33、ot lead to the failure. The data is representative ofthe sample material.X1.3 Failure Shape:X1.3.1 Machine Direction Tear (MD-T)A tear in themachine direction.X1.3.2 Transverse Direction Tear (TD-T)A tear in thetransverse direction.X1.3.3 Multi-Directional Tear (XD-T)A tear for severaltears that do

    34、not follow any single direction.X1.3.4 HoleCircular or elliptical hole in the specimen.Material may or may not have thinned over a broad region.X1.3.5 Hole in Cat Eye (H-Cat)Circular or elliptical holein an area where the material has significantly necked downand thinned. The large thinned area rese

    35、mbles a pupil of a cateye.X2. STRESS-STRAIN CALCULATIONS FOR DEFINED SHAPES (ARC OF A SPHERE OR ELLIPSOID)X2.1 Strain CalcualtionsX2.1.1 :For d L/2, one must use the calculations of EqX2.4-X2.7 and 11 up to d = L/2, and then use Eq X2.7 and X2.8 and 12from d L/2 until failure.X2.1.3 For non-defined

    36、geometric shapes no calculationsare necessary.D5617044ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent r

    37、ights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either f

    38、or revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair heari

    39、ng you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).D5617045


    注意事项

    本文(ASTM D5617-2004 Standard Test Method for Multi-Axial Tension Test for Geosynthetics《土工合成织物多轴抗拉试验的标准试验方法》.pdf)为本站会员(李朗)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开