欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM D5130-1995(2003) Standard Test Method for Open-Channel Flow Measurement of Water Indirectly by Slope-Area Method《使用比降面积法迂回测量明渠水流流量的标准试验方法》.pdf

    • 资源ID:518935       资源大小:634.58KB        全文页数:12页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM D5130-1995(2003) Standard Test Method for Open-Channel Flow Measurement of Water Indirectly by Slope-Area Method《使用比降面积法迂回测量明渠水流流量的标准试验方法》.pdf

    1、Designation: D 5130 95 (Reapproved 2003)Standard Test Method forOpen-Channel Flow Measurement of Water Indirectly bySlope-Area Method1This standard is issued under the fixed designation D 5130; the number immediately following the designation indicates the year oforiginal adoption or, in the case of

    2、 revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the computation of discharge(the volume rate of flow) of water in open

    3、 channels or streamsusing representative cross-sectional characteristics, the water-surface slope, and coefficient of channel roughness as input togradually-varied flow computations.21.2 This test method produces an indirect measurement ofthe maximum discharge for one flow event, usually a specificf

    4、lood. The computed discharge may be used to help define thehigh-water segment of a stage-discharge relation.1.3 The values stated in inch-pound units are to be regardedas the standard. The SI units given in parentheses are forinformation only.1.4 This standard does not purport to address all of thes

    5、afety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:D 1129 Terminology Relating to

    6、 Water3D 2777 Practice for Determination of Precision and Bias ofApplicable Methods of Committee D-19 on Water3D 3858 Practice for Open-Channel Flow Measurement ofWater by Velocity-Area Method32.2 ISO Standards:ISO 748 Liquid Flow Measurements in Open ChannelsVelocity-Area Method4ISO 1070 Liquid Flo

    7、w Measurements in Open ChannelsSlope-Area Method43. Terminology3.1 Definitions: For definitions of terms used in this testmethod, refer to Terminology D 1129.3.2 Definitions of Terms Specific to This Standard: Severalof the following terms are illustrated in Fig. 1:3.2.1 alpha (a)a velocity-head coe

    8、fficient that representsthe ratio of the true velocity head to the velocity headcomputed on the basis of the mean velocity. It is assumed equalto 1.0 if the cross section is not subdivided. For subdividedsections, a is computed as follows:a5(Ski3Ai2DKT3AT2where:1This test method is under the jurisdi

    9、ction of ASTM Committee D19 on Waterand is the direct responsibility of Subcommittee D19.07 on Sediments, Geomor-phology, and Open-Channel Flow.Current edition approved June 10, 2003. Published August 2003. Originallyapproved in 1990. Last previous edition approved in 1999 as D 5130 95 (1999).2This

    10、test method is similar to methods developed by the U.S. GeologicalSurvey and described in documents referenced in Footnotes 5, 6, and 7.3Annual Book of ASTM Standards, Vol 11.01.4Available from American National Standards Institute, 25 W. 43rd St., 4thFloor, New York, NY 10036.FIG. 1 Definition Sket

    11、ch of a Slope-Area Reach1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.K and A = the conveyance and area of the subsectionindicated by the subscript i, andKTand AT= the conveyance and area of the entire crosssection.3.2.2 conveyance

    12、 (K)a measure of the carrying capacityof a channel and has dimensions of cubic feet per second orcubic metres per second. Conveyance is computed as follows:K 51.486nAR2/3where:n = the Manning roughness coefficient,A = the cross-section area, ft2(m2), andR = the hydraulic radius, ft (m).NOTE 11.486 =

    13、 1.00 SI unit.3.2.3 cross sections (numbered consecutively in downstreamorder)representative of a reach of channel and are positionedas nearly as possible at right angles to the direction of flow.They must be defined by coordinates of horizontal distance andground elevation. Sufficient ground points

    14、 must be obtained sothat straight-line connection of the coordinates will adequatelydescribe the cross-section geometry. If major breaks in thehigh-water profile are evident, cross sections should be locatedat the breaks.3.2.4 cross-section area (A)the area of the water belowthe high-water surface e

    15、levations that are computed by assum-ing a straight-line interpolation between elevations on eachbank. The area is computed as the summation of the productsof mean depth multiplied by the width between stations of thecross section.3.2.5 friction loss (hf)the loss due to boundary friction inthe reach

    16、 and is equivalent to the following:D h 1Dhv2 kDhv!where:Dh = the fall in the reach,Dhv= the upstream velocity head minus the down-stream velocity head,(kDhv) = the energy loss due to acceleration or decelerationand to eddies in a contracting or expanding reach,where k is a coefficient for energy lo

    17、sses.All of the equations presented in this standard are based onthe assumption that k is zero for contracting reaches and 0.5 forexpanding reaches.3.2.6 fall (Dh)the drop in the water-surface computed asthe difference in the average water-surface elevation at adja-cent cross sections.3.2.7 friction

    18、 slope (Sf)the energy loss divided by thelength of the reach or:Sf5hfLthat becomes:Sf5Dh 1DhvLwhen Dhvis negative (for a contracting reach),or:Sf5Dh 1Dhv2Lwhen D hvis positive (for an expanding reach).3.2.8 Froude number (F)an index to the state of flow inthe channel. In a prismatic channel, the flo

    19、w is tranquil orsubcritical if the Froude number is less than 1.0 and is rapid orsupercritical if it is greater than 1.0. The Froude number iscomputed as follows:F 5V=gdmwhere:V = the mean velocity in ft/s (m/s),dm= the average depth in the cross section in feet, andg = the acceleration of gravity i

    20、n ft/s/s (m/s/s).3.2.9 high-water marksthe evidence of the highest stagereached by a flood. Debris, stains, foam lines, and scour marksare common types of high-water marks. Water-surface slopesare determined by the elevations of these marks.3.2.10 hydraulic radius (R)defined as the area of a crossse

    21、ction or subsection divided by the corresponding wettedperimeter.3.2.11 roughness coeffcient (n) or Mannings n is used inthe Manning equation. Roughness coefficient or Mannings n isa measure of the resistance to flow in a channel. The factorsthat influence the magnitude of the resistance to flow inc

    22、ludethe character of the bed material, cross section irregularities,depth of flow, vegetation, and alignment of the channel. Areasonable evaluation of the resistance to flow in a channeldepends on the experience of the person selecting the coeffi-cient and reference to texts and reports that contain

    23、 values forsimilar stream and flow conditions.5,6(See 9.3).3.2.12 velocity head (hv)computed as follows:hv5aV22gwhere:a = the velocity-head coefficient,V = the mean velocity in the cross section in ft/s (m/s), andg = the acceleration of gravity in ft/s/s (m/s/s).3.2.13 wetted perimeter (WP)the total

    24、 length of theboundary between the channel bed and the water for a crosssection. It is computed as the sum of the hypotenuse of theright triangle defined by the distance between adjacent stationsof the cross section and the difference in bed elevations.5Benson, M. A., and Dalrymple, T., “General Fie

    25、ld and Office Procedures forIndirect Discharge Measurements,” Techniques of Water Resources Investigations,Book 3, Chapter , U.S. Geological Survey, 1967.6Matthai, Howard F., “Measurement of Peak Discharge at Width Contractionsby Indirect Methods,” Techniques of Water Resources Investigations, Book

    26、3,Chapter A4, U.S. Geological Survey, 1984.D 5130 95 (2003)24. Summary of Test Method4.1 The slope-area method is used to indirectly determinethe discharge through a reach of channel, usually after a flood,using evidence left by the event and the physical characteristicsof the channel reach. A field

    27、 survey is made to determinedistances between and elevations of high-water marks and todefine cross sections of the stream. These data are used tocompute the fall in the water surface between sections andselected properties of the sections. This information is usedalong with Mannings n in the Mannin

    28、g equation to computethe discharge, Q. The Manning equation in terms of discharge,Q, is as follows:Q 51.486nAR2/3Sfor Q5 KSfThe symbols on the right sides of the equations are definedin Section 3.5. Significance and Use5.1 This test method is particularly useful for determiningthe discharge when it

    29、cannot be measured directly by sometype of current meter to obtain velocities and with soundingweights to determine the cross section.5.2 Even under optimum conditions, the personnel availablecannot cover all points of interest during a major flood. Fieldpersonnel cannot always obtain reliable resul

    30、ts by directmethods if the stage is rising or falling very rapidly, if flowingice or debris interferes with depth or velocity measurements.5.3 Under the worst conditions, access roads are blocked,cableways and bridges may be washed out, and knowledge ofthe flood frequently comes too late to obtain d

    31、irect measure-ments of flow. Therefore, some type of indirect measurement isnecessary. The slope-area method is a commonly used method.6. Apparatus6.1 The equipment generally used for a “transit-stadia”survey is recommended. An engineers transit, a self-levelinglevel with azimuth circle, newer equip

    32、ment using electroniccircuitry, or other advanced surveying instruments may beused. Standard level rods, a telescoping, 25-ft (7.6 m) level rod,rod levels, hand levels, steel and metallic tapes, tag lines (smallwires with markers fixed at known spacings), vividly coloredflagging, survey stakes, a ca

    33、mera (preferably stereo) with colorfilm, light meter, and ample note paper are necessary items.6.2 Additional equipment that may expedite a survey in-clude axes, shovels, a portable drafting machine, a boat withoars and motor, hip boots, waders, rain gear, nails, soundingequipment, two-way radios, l

    34、adder, and rope.6.3 Safety equipment should include life jackets, first aidkit, drinking water, and pocket knives.7. Sampling7.1 Sampling as defined in Terminology D 1129 is notapplicable in this test method.8. Calibration8.1 The surveying instruments, levels and transits, etc.,should have their adj

    35、ustment checked before each use andpossibly daily when in continuous use or after some occurrencethat may have affected the adjustment.8.2 The standard check is the “two-peg” or“ double-peg”test. If the error is over 0.03 ft in 100 ft (0.9 cm in 30.5 m), theinstrument should be adjusted. The two-peg

    36、 test and how toadjust the instrument are described in many surveying text-books and in instructions provided by the manufacturer. Referto manufacturers manual for the electronic instruments.8.3 If the “reciprocal leveling” technique is used in thesurvey, it is the equivalent of the two-peg test bet

    37、ween each ofthe two successive hubs.8.4 Sectional and telescoping level rods should be checkedvisually at frequent intervals to be sure sections are notseparated. A proper fit at each joint can be quickly checked bymeasurements across the joint with a steel tape.8.5 All field notes of the transit-st

    38、adia survey should bechecked before proceeding with the computations.9. Procedure9.1 Selection of a reach of channel is the first and probablythe most important step to obtain reliable results. Ideal reachesrarely exist; so the various elements in a reach must beevaluated and compromises made so tha

    39、t the best reachavailable is selected.7Selection soon after the flood event isrecommended because livestock, humans, heavy rain, and banksloughing can destroy high-water marks.9.1.1 Good high-water marks are essential for good results.At times a reach with poor quality marks must be used becauseof o

    40、ther complicating factors such as inflow, proximity to agaging station, etc. List high-water marks in a format such asshown in Fig. 2.9.1.2 The nearer the reach to a uniform channel the better.Marked changes in channel shape should be avoided becauseof uncertainties regarding the value of the expans

    41、ion/contraction loss coefficient ( k) and the friction losses in thereach. Changes in channel conveyance should be fairly uni-form from section to section to be consistent with the assump-tion that the mean conveyance is equal to the geometric meanof the conveyances at the end sections.9.1.3 A reach

    42、 with flow confined to a roughly trapezoidalchannel is desirable because roughness coefficients have beendetermined for such shapes. However, compound channels,those with overbank flow, for example, can be used if they areproperly subdivided into subareas that are approximatelytrapezoidal.9.1.4 A st

    43、raight reach that contracts is preferred, but bothconditions seldom exist in the same reach. Whether or not areach is contracting or expanding depends solely upon thedifference in velocity head (Dhv) between sections. The reachis contracting if the difference in the velocity head is negative.The rea

    44、ch is expanding if the velocity-head difference ispositive.9.1.5 Cross sections are assumed to be carrying water inaccordance with the conveyance for each part of the section.7Benson, M. A., and Dalrymple, Tate, “Measurement of Peak Discharge by theSlope-Area Method,” Techniques of Water Resources I

    45、nvestigations, Book 3,Chapter . U.S. Geological Survey, 1967.D 5130 95 (2003)3Therefore, the channel for some distance upstream should besimilar to that of the reach. Then the discharge will bedistributed in relation to depths, roughness, and shape. If theupstream section is located too close to a s

    46、harp bend, a bridgethat constricts the width, or a natural constriction, slack water,or even an eddy may occupy part of the section; and the sectionwill not be effective in carrying water downstream in propor-tion to the computed conveyance.9.1.6 Channels in mountainous areas may be very rough andst

    47、eep and may have free fall over riffles and boulders. TheManning equation is not applicable when free fall exists.However, free fall may or may not be indicated by thehigh-water profiles or by inspection of the reach. Crosssections can be located to eliminate any part of a reach inwhich free fall is

    48、 indicated. If the reach includes stretches inwhich free fall might have occurred, the computed dischargesare not reliable.9.1.7 The reach should be long enough to develop a fall thatis well beyond the range of error in the surveying method, inalternative interpretations of the high-water profile, o

    49、r inuncertainties related to the computation of the velocity head.One suggested criteria is that the fall in the reach should be 0.5ft (0.15 m) or greater than the velocity head in the reach, orboth.9.2 Cross sections represent the geometry of a reach ofchannel. For example: section 2 should be typical of the reachfrom halfway upstream to section 1 to halfway downstream tosection 3. A minimum of three cross sections is highlyrecommended.9.2.1 Locate cross sections at major breaks in the high-waterprofiles. To do so, the high-water marks should be plotted inth


    注意事项

    本文(ASTM D5130-1995(2003) Standard Test Method for Open-Channel Flow Measurement of Water Indirectly by Slope-Area Method《使用比降面积法迂回测量明渠水流流量的标准试验方法》.pdf)为本站会员(outsidejudge265)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开