欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM D4570-2002(2017) Standard Test Method for Rubber Chemicals&x2014 Determination of Particle Size of Sulfur by Sieving (Dry)《橡胶化学品的标准试验方法 筛分法测定硫磺粒度(干)》.pdf

    • 资源ID:517393       资源大小:54.03KB        全文页数:2页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM D4570-2002(2017) Standard Test Method for Rubber Chemicals&x2014 Determination of Particle Size of Sulfur by Sieving (Dry)《橡胶化学品的标准试验方法 筛分法测定硫磺粒度(干)》.pdf

    1、Designation: D4570 02 (Reapproved 2017)Standard Test Method forRubber ChemicalsDetermination of Particle Size of Sulfurby Sieving (Dry)1This standard is issued under the fixed designation D4570; the number immediately following the designation indicates the year oforiginal adoption or, in the case o

    2、f revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the particle size measurement ofthe coarse fraction of ground sulfurs.

    3、 It is limited to measure-ment of particles greater than 45 m (No. 325 sieve). If thesulfur is very fine and the screens become plugged by thecaking of the sulfur, it may be necessary to use a wet sieveprocedure instead.1.2 The values stated in SI units are to be regarded as thestandard.1.3 This sta

    4、ndard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1

    5、ASTM Standards:2E11 Specification for Woven Wire Test Sieve Cloth and TestSievesE145 Specification for Gravity-Convection and Forced-Ventilation Ovens3. Significance and Use3.1 This test method is used to evaluate sulfur for suitabilityas a rubber vulcanizing agent. Sulfur particles must be smalleno

    6、ugh to dissolve in rubber during cure to produce a uniformnetwork of cross-links. This test method is used as a qualitycontrol method to ensure that large particles are not present(and to determine if the sulfur follows a typical pattern for sizedistribution).4. Apparatus4.1 Standard Sieves, stainle

    7、ss steel, 203 mm in diameterconforming to Specification E11. The stainless steel cloth shallrange in mesh size from 45 to 250 m. The sieve set shouldinclude a lid and a bottom pan.4.2 Mechanical Sieve Shakers, such as a Tyler Ro-Tap3orequivalent unit.4.3 Balance, with a minimum capacity of 500 g sen

    8、sitive to0.1 g.4.4 Balance, with a minimum capacity of 150 g sensitive to0.001 g.4.5 Oven, circulating air type, controlled to 70 6 2C.5. Reagent5.1 Tri-calcium Phosphate, screened to a fineness of lessthan 45 m.6. Procedure6.1 Weigh each sieve to the nearest 0.1 g and assemble inorder of increasing

    9、 mesh size from bottom to top.Add a bottompan. Choice of sieves depends on the information desired.6.2 Into a beaker or suitable container, weigh precisely100.0 g of sulfur to the nearest 0.1 g. When the sulfur is veryfine, add 2.0 g of tri-calcium phosphate (see 5.1) and blendthoroughly using a spa

    10、tula.6.3 Transfer all the sulfur to the top sieve and add the lid.Fix the sieve vest firmly in the mechanical sieve shaker. Runthe unit for 10 min, stop, remove the sieves, and weigh eachsieve to the nearest 0.1 g. Return the sieves to the unit and runan additional 3 min. Reweigh each sieve again to

    11、 the nearest0.1 g. Repeat until the sieves reach constant mass.7. Calculation7.1 Determine the residue remaining on each sieve by massdifference. For higher precision, transfer the small residue fromthe coarser screen to a weighing dish and weigh to the nearest0.01 g.1This test method is under the j

    12、urisdiction of ASTM Committee D11 on Rubberand Rubber-like Materials and is the direct responsibility of Subcommittee D11.20on Compounding Materials and Procedures.Current edition approved Feb. 1, 2017. Published February 2017. Originallyapproved in 1986. Last previous edition approved in 2012 as D4

    13、570 02 (2012).DOI: 10.1520/D4570-02R17.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3This unit may be purc

    14、hased from the Fisher Scientific Co., 585 Alpha Dr.,Pittsburgh, PA 15238.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardizat

    15、ion established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.17.2 The percent residue on each screen is equal to theamount in grams on each screen.7.3 The per

    16、cent residue passing through each screen isdetermined by accumulating the total percent material col-lected on that screen and the coarser screens used andsubtracting the total from 100.% residue through (for any screen) =100 sumation of % sulfur collected on thatscreen and on any coarser screens8.

    17、Report8.1 The report should include the following information:8.1.1 Proper identification of samples,8.1.2 Identification of each screen used,8.1.3 The percent residue on each screen, and8.1.4 The percent residue through for each screen.9. Precision and Bias9.1 Round robin testing will be conducted,

    18、 and precisionand bias statements will be balloted for inclusion upon thecompletion of this work.10. Keywords10.1 dry sieving; particle size; sulfurASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users

    19、of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every fi

    20、ve years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical

    21、committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, P

    22、A 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 02 (2017)2


    注意事项

    本文(ASTM D4570-2002(2017) Standard Test Method for Rubber Chemicals&x2014 Determination of Particle Size of Sulfur by Sieving (Dry)《橡胶化学品的标准试验方法 筛分法测定硫磺粒度(干)》.pdf)为本站会员(fatcommittee260)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开