欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM D4251-1989(2003) Standard Test Method for Active Matter in Anionic Surfactants by Potentiometric Titration《用电势滴定法测定阴离子表面活性剂中活性物质含量的标准试验方法》.pdf

    • 资源ID:516632       资源大小:53.42KB        全文页数:4页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM D4251-1989(2003) Standard Test Method for Active Matter in Anionic Surfactants by Potentiometric Titration《用电势滴定法测定阴离子表面活性剂中活性物质含量的标准试验方法》.pdf

    1、Designation: D 4251 89 (Reapproved 2003)Standard Test Method forActive Matter in Anionic Surfactants by PotentiometricTitration1This standard is issued under the fixed designation D 4251; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revis

    2、ion, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method describes a potentiometric titrationprocedure for determining the anionic active ma

    3、tter in deter-gents. It is intended for the analysis of anionic surfactants suchas detergent range alkylbenzenesulfonates, a-olefin sulfonates,alcohol sulfates, and alcohol ethosulfates. It has not been testedfor surfactant formulations.1.2 This standard does not purport to address all of thesafety

    4、concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use. Material SafetyData Sheets are available for reagents and materials. Reviewth

    5、em for hazards prior to usage.2. Referenced Documents2.1 ASTM Standards:D 459 Terminology Relating to Soaps and Other Deter-gents2D 1193 Specification for Reagent Water3D 1681 Test Method for Synthetic Anionic Active Ingredi-ent in Detergents by Cationic Titration Procedure2D 3049 Test Method for Sy

    6、nthetic Anionic Ingredient byCationic Titration2E 180 Practice for Determining the Precision of ASTMMethods for Analysis and Testing of Industrial Chemicals43. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 active matterthe organic surface-active materialpresent in the detergent

    7、 and defined in Terminology D 459 asactive ingredient of a synthetic detergent.4. Summary of Test Method4.1 A detergent sample containing active matter is titratedpotentiometrically in an aqueous medium with a standardsolution of Hyamine 1622 using a nitrate ion-selective elec-trode. The titration r

    8、eaction involves the formation of acomplex between the cationic quaternary ammonium titrant(Hyamine 1622) and the anionic surfactant which precipitates.The nitrate electrode probably responds to the concentration ofunreacted anionic surfactant.5. Significance and Use5.1 Anionic surfactants are the m

    9、ost widely used of thesynthetic detergents. ASTM methods in current use for theirdetermination involve two-phase aqueous/chloroform titrationswith the organic dyes methylene blue (Test Method D 1681) ordisulphine blue/dimidium bromide (Test Method D 3049) asindicators. One advantage of the potentiom

    10、etric method is thatit eliminates the use of chloroform whose use is restricted forenvironmental and toxicological reasons.5.2 This test method is intended for use as described in 1.1.6. Apparatus6.1 Potentiometric Titration Assembly, consisting of anautomatic titrator (Metrohm E536 or equivalent) f

    11、itted with anitrate ion-selective electrode (Orion Model 93-07 Nitrate ISE,or equivalent) and a Ag/AgCl reference electrode (Metrohm1This test method is under the jurisdiction of ASTM Committee D12 on Soapsand Other Detergents and is the direct responsibility of Subcommittee D12.12 onAnalysis of Soa

    12、ps and Synthetic Detergents.Current edition approved May 26, 1989. Published July 1989. Originallypublished as D 4251 83. Last previous edition D 4251 88.2Annual Book of ASTM Standards, Vol 15.04.3Annual Book of ASTM Standards, Vol 11.01.4Annual Book of ASTM Standards, Vol 15.05.TABLE 1 Active Matte

    13、r Content of Various Anionic Surfactantsby the Potentiometric Titration and Two-Phase Titration MethodsAnionic SurfactantActive Matter Content, % weightPotentiometric Titration Two-PhaseTitrationOrionNO3(#1)OrionNO3(#2)“Old” HNUNO3Sulframin AOS (alpha-olefin sulfonate)41.0342.5042.6441.4940.7441.344

    14、0.9141.0541.0539.21A39.26Sulframin 1298 (alkylarylsulfonate)94.1595.3194.7396.2695.6796.2694.9195.5094.9195.12B95.12NEODOLT 25-3S (alcoholethoxysulfate sodiumsalt)58.1258.8158.1257.9457.7457.9457.7557.9557.9558.19B58.24AMethylene blue method.BMixed indicator method.1Copyright ASTM International, 100

    15、 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.EA 440 or equivalent) together with a buret assembly having a5-mL buret (Metrohm E575) and 150-mL beaker. A TFE-fluorocarbon star-head stirring bar can be used to providemixing and eliminate foaming during titration. Us

    16、e of theOrion electrode with a Metrohm E536 requires an adapter(Metrohm EA-1046/2).NOTE 1The conditioning of the electrode is essential for obtaining agood break in the titration curve. Conditioning new electrodes in 0.01 MNaNO3aqueous solution for 60 min (or more) prior to use is recom-mended. Cond

    17、ition previously used electrodes by using again for thetitration of aqueous sodium lauryl sulfate with Hyamine.NOTE 2Other electrodes (for example a calomel electrode) aresuitable as the reference electrode provided they give a stable referencepotential during the titration. Reference electrodes hav

    18、ing a ceramic or anasbestos junction tend to clog with use. Therefore, a ground-glass sleeveelectrode (such as the Metrohm EA 440) is suggested.7. Reagents7.1 Hyamine 1622,5diisobutylphenoxyethoxyethyl dim-ethyl benzyl ammonium chloride.7.2 Sodium Lauryl Sulfate,6primary standard (Note 3).NOTE 3Sodi

    19、um lauryl sulfate must be analyzed for purity accordingto the Reagent section of Test Method D 3049, before using as a primarystandard.7.3 Water, type III reagent water conforming to Specifica-tion D 1193.8. Preparation of Standard Reagents8.1 Sodium Lauryl Sulfate Solution,43 102NWeighaccurately 11

    20、.5 6 0.5 g of sodium lauryl sulfate to 0.1 mg;dissolve in water and dilute to a final volume of 1 L. Calculatethe normality of the solution with the following equation:Normality of sodium lauryl sulfate 5W!P!288.38!100!(1)where:P = purity of the sodium lauryl sulfate, weight %, andW = weight of sodi

    21、um lauryl sulfate, g.8.1.1 Keep the solution no longer than 1 month beforemaking a fresh solution.8.2 Hyamine 1622 Solution,43 102NDissolve 18 6 0.5g of Hyamine 1622 in deionized water. Transfer to a 1-Lvolumetric flask. Add 0.4 mL of 50 % NaOH and dilute tovolume with water. Standardize following t

    22、he same proceduredescribed for the sample titration using 5 mL of the sodiumlauryl sulfate solution. Calculate the normality of the Hyaminesolution as follows:Normality of Hyamine 1622 5A!B!C!(2)where:A = sodium lauryl sulfate solution used, mL,B = normality of sodium lauryl sulfate, andC = Hyamine

    23、solution consumed during titration, mL.9. Procedure9.1 Add to a 150-mL beaker a known weight of detergentsample together with enough water to make 50 mL of solution(Note 4). The solution should cover the sensing tips of theelectrodes. Titrate initially by adding Hyamine solution atapproximately 0.5

    24、mL/min while stirring constantly. As theinflection point is approached, reduce the addition rate, andcontinue titrating well past the inflection in the titration curve.(Automatic titrators can be preset to automatically slow downthe addition rate as the inflection point is approached.)NOTE 4To deter

    25、mine the amount of sample needed for an approxi-mate 3.75-mL titration (0.15 meq) use the following equation:W 50.015!MD!(3)where:W = weight of sample to be taken for analysis, g,M = average equivalent weight of the anionic active matter present,andD = approximate concentration of anionic active mat

    26、ter expected,weight %.9.1.1 To obtain accurate weights of sample, it is convenientto make up an aqueous solution (for example 250 mL) and takean aliquot corresponding to 0.15 meq of active matter.9.1.2 The electrode should be cleaned between each titra-tion. A satisfactory procedure is to first rins

    27、e it with water, thenwith alcohol (ethyl alcohol) (Note 5) and again with waterfollowed by wiping the surface with a Kimwipe.NOTE 5The electrode can be quickly washed with ethyl alcohol whenfollowed immediately by a water rinse. Prolonged contact of the electrodewith alcohol or other organic solvent

    28、 can cause failure of the electrodemembrane.9.2 Graphically select the inflection point of the curve onthe recorder chart. Typical titration curves of several anionicsurfactants are shown in Fig. 1.10. Calculation10.1 Calculate the anionic active matter content of thesample as follows:Anionic Active

    29、 Matter, % w 5V!N!M!10!W!(4)where:V = Hyamine 1622 solution consumed in titration, mL,N = normality of Hyamine,W = weight of sample g, andM = average equivalent weight of the anionic active mat-ter present.10.2 Calculate the milliequivalents of active matter per 100g sample as follows:meq Active Mat

    30、ter/100 g 5V!N!100!W!(5)5Available from Gallard Schlesinger Chemical Manufacturing Corp., 584Mineola Ave., Carle Place, NY 11514.6Available from British Drug House, LTD, or in the U.S. from GallardSchlesinger Chemical Mfg. Corp., 584 Mineola Ave., Carle Place, NY 11514.D 4251 89 (2003)2where V, N, a

    31、nd W are as listed previously.11. Precision11.1 The following criteria should be used to judge theacceptability of the results (Note 6):7,811.1.1 Repeatability (Single Analyst)The standard devia-tion of results (each the average of duplicates), obtained by thesame analyst on different days, has been

    32、 estimated to be 0.66weight % relative at 28 df. Two such averages should beconsidered suspect (95 % confidence level) if they differ bymore than 1.9 weight % relative.11.1.2 Reproducibility (multilaboratory)The standard de-viation of results (each the average of duplicates), obtained tobe 1.3 weigh

    33、t % relative at 6 df. Two such averages should beconsidered suspect (95 % confidence level) if they differ bymore than 4.5 weight % relative.11.1.3 Checking Limits for DuplicatesReport the weight% active matter of the sample to the nearest 0.1 weight %.Duplicate runs that agree within 1.8 weight % r

    34、elative areacceptable for averaging (95 % confidence level).NOTE 6The precision data were derived from results of the coopera-tive tests by eight laboratories on the following surfactants (equivalentweights in parenthesis): sodium lauryl sulfate (302), alcohol ethoxysulfateammonium salt (434), a-ole

    35、fin sulfonate (325), alkylaryl sulfonic acid(318).12. Keywords12.1 active matter; anionic surfactants; titration7Data supporting the precision statements are on file at ASTM Headquarters, 100Barr Harbor Drive, West Conshohocken, PA 19428, Research Report No. D12-1003.8The statistical analysis was pe

    36、rformed in accordance with Practice E 180 fordeveloping precision estimates.FIG. 1 Potentiometric Titration Curves of Various Anionic Surfactants versus 0.03757 N Hyamine 1622 Using the Orion Model 93-07Nitrate ISED 4251 89 (2003)3ASTM International takes no position respecting the validity of any p

    37、atent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revisi

    38、on at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your co

    39、mments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrigh

    40、ted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).D 4251 89 (2003)4


    注意事项

    本文(ASTM D4251-1989(2003) Standard Test Method for Active Matter in Anionic Surfactants by Potentiometric Titration《用电势滴定法测定阴离子表面活性剂中活性物质含量的标准试验方法》.pdf)为本站会员(Iclinic170)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开