欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM D3971-1989(2004) Standard Test Method for Dichloromethane-Soluble Matter in Cellulose《纤维素中二氯甲烷可溶物的标准试验方法》.pdf

    • 资源ID:515933       资源大小:21.80KB        全文页数:2页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM D3971-1989(2004) Standard Test Method for Dichloromethane-Soluble Matter in Cellulose《纤维素中二氯甲烷可溶物的标准试验方法》.pdf

    1、Designation: D 3971 89 (Reapproved 2004)Standard Test Method forDichloromethane-Soluble Matter in Cellulose1This standard is issued under the fixed designation D 3971; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of las

    2、t revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the determination ofdichloromethane-soluble matter in cellulose and is applicableto dissolving-t

    3、ype cellulose pulps prepared from cotton orwood.1.2 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of reg

    4、ulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D 1348 Test Methods for Moisture in Cellulose3. Summary of Test Method3.1 A sample is extracted with dichloromethane in a Soxhletapparatus as a measure of the waxes, fats, resins, and oilspresent.4. Significance and Use4.1 D

    5、ichloromethane-soluble materials are typically re-ferred to as extractives. These extractives are comprised oforganic materials that originated in the wood or cotton. Themeasure is an indication of the efficiency of removal of thesesubstances during pulping and bleaching. The extractive levelis of c

    6、oncern to dissolving pulp users since the presence oflarge amounts of extractives could inhibit the processing ofcellulose into the desired derivative.5. Apparatus5.1 Extraction Apparatus:5.1.1 Soxhlet.5.1.2 Flask, 250-mL.5.1.3 Extractor Tube, with standard taper 45/50 top joint.5.1.4 Allihn Standar

    7、d Taper, 45/50 or5.1.5 Friedrichs Standard Taper, 45/50 type condenser.5.2 Extraction Thimble, either (1) standard thickness paper,43 by 123 mm, (2) aluminum oxide, 34 by 100 mm, mediumporosity, or (3) glass with coarse-porosity fritted-glass disk, 45by 130 mm.5.3 Heating DeviceSteam bath or heating

    8、 mantle.5.4 Oven, maintained at 105 6 3C.5.5 Dish, evaporating, disposable, light aluminum, 63 mmin diameter by 17.5 mm deep.5.6 Desiccator with efficient desiccant.6. Reagent6.1 Dichloromethane, ACS, 99 % CH2Cl2, having a residueafter evaporation of less than 0.002 %.7. Procedure7.1 Weigh 8 to 12 g

    9、 of loose pulp, to the nearest 0.01 g, intoan extractor thimble that has previously been extracted withdichloromethane. For sheet pulp, cut a sample into strips about10 mm wide and 70 mm long, and weigh about 20 g into athimble. Weigh a separate portion for a moisture determinationin accordance with

    10、 Test Methods D 1348.7.2 Place the extraction thimble with sample in the extractorand connect the flask. Pour 250 mL of the dichloromethane intothe body of the extractor. Connect the assembled extractor tothe condenser and place the flask in the heating device. Turn onthe cooling water to the conden

    11、ser and adjust the heating rateto cause siphoning 6 to 8 times per hour. Continue theextraction for 5 h.7.3 Heat the evaporating dish in the oven at 105C for 30min, cool in a desiccator, and weigh to the nearest 0.1 mg.7.4 When the extraction is complete, disconnect the flask ata time when most of t

    12、he solvent has collected in the extractor.Partially evaporate the solvent in the extraction flask to avolume of 15 to 20 mL. Transfer the extract to the taredweighing dish by washing with three 5-mL portions of freshsolvent.7.5 Place the dish on a steam hot plate and evaporate just todryness. Then p

    13、lace the dish in the oven at 105C for 1 h, coolin a desiccator, and weigh to the nearest 0.1 mg. (WarningCare must be taken to keep the steam hot plate surface clean in1This test method is under the jurisdiction of ASTM Committee D01 on Paintand Related Coatings, Materials, and Applications and is t

    14、he direct responsibility ofSubcommittee D01.36 on Cellulose and Cellulose Derivatives.Current edition approved June 1, 2004. Published June 2004. Originallyapproved in 1980. Last previous edition approved in 1999 as D 3971 89 (1999).2For referenced ASTM standards, visit the ASTM website, www.astm.or

    15、g, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.order to prev

    16、ent contamination of the bottom of the aluminumdish and a subsequent unmeasured increase in tare weight.)7.6 Run a blank determination with the solvent used in thetest. Evaporate 250 mL of the solvent to dryness and weigh theresidue to the nearest 0.1 mg. Correct the weight of the driedextract by th

    17、e weight of residue found.8. Calculation8.1 Calculate the percent of dichloromethane-soluble mat-ter, D, on the dry basis as follows:D 5 We2 Wb!/Ws100 2 M!/100 3 100where:We= oven-dry weight of extract, g,Wb= oven-dry weight of solvent blank determined in 7.6,g,Ws= weight of sample, g, andM = moistu

    18、re in sample, % (Test Methods D 1348).9. Report9.1 Report the dichloromethane-soluble matter to the near-est 0.01 %.10. Precision and Bias10.1 Results of a round robin study by five laboratoriesshowed that for a content of 0.20 % extractives the relativestandard deviation was 10 %. For samples at th

    19、e 0.15 % levelthe relative standard deviation was 7 %.10.2 No statement of bias can be made as no suitablereference material exists for determining bias.11. Keywords11.1 dissolving types of cellulose pulps; extractives; fat;removal efficiency of bleaching and pulping; resin; soxhlet;waxASTM Internat

    20、ional takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely the

    21、ir own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should

    22、be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standar

    23、ds, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).D 3971 89 (2004)2


    注意事项

    本文(ASTM D3971-1989(2004) Standard Test Method for Dichloromethane-Soluble Matter in Cellulose《纤维素中二氯甲烷可溶物的标准试验方法》.pdf)为本站会员(outsidejudge265)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开