欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM D3954-1994(2004) Standard Test Method for Dropping Point of Waxes《石蜡滴点的标准试验方法》.pdf

    • 资源ID:515896       资源大小:22.11KB        全文页数:2页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM D3954-1994(2004) Standard Test Method for Dropping Point of Waxes《石蜡滴点的标准试验方法》.pdf

    1、Designation: D 3954 94 (Reapproved 2004)Standard Test Method forDropping Point of Waxes1This standard is issued under the fixed designation D 3954; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number

    2、 in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the determination of the ASTMdropping point for waxes.1.2 This standard does not purport to address all of thesafety

    3、 concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D 566 Test Method for Dropping Poi

    4、nt of LubricatingGreaseD 2265 Test Method for Dropping Point of LubricatingGrease Over Wide Temperature Range3. Summary of Test Method3.1 In this test method, the dropping point is defined as thetemperature at which the wax suspended in a cylindrical cup,with a 2.8-mm diameter hole in the bottom, fl

    5、ows downward adistance of 19 mm to interrupt a light beam as the sample isheated at a constant rate in air.4. Significance and Use4.1 Waxes do not go through a sharp solid-liquid phasechange when heated and therefore do not have a true meltingpoint. As the temperature rises, waxes gradually soften o

    6、rbecome less viscous. For this reason, the determination of thesoftening point must be made by an arbitrary but closelydefined method if test values are to be reproducible.4.2 This test is useful in determining the consistency ofwaxes, and as one element in establishing the uniformity ofshipments or

    7、 source of supply.4.3 This test method has been found suitable for all types ofwaxes including paraffin, microcrystalline polyethylene, andnatural waxes.5. Apparatus5.1 Suitable apparatus that meets the requirements of 5.1.1,5.1.2, and 5.1.3 can be used to determine dropping points bythis test metho

    8、d. Instruments are available commercially3consisting of a control unit with a digital temperature recorder,matched furnace, sample cartridges, and accessories. Thecontrol unit automatically maintains the furnace temperatureand controls the heating rate with a precision of 0.1C. Thedropping point is

    9、automatically recorded, and the furnaceheating program is turned off when the sample interrupts thelight beam and triggers the photocell detector.5.1.1 Control UnitThis unit shall provide a continuouslinear temperature control from 25 to 250C at a 2C/min rate.A digital readout shall record the softe

    10、ning point with anaccuracy of 0.1C.5.1.2 Furnace UnitThis unit shall be capable of heating asample cup assembly as described in 5.1.3 at 2C 6 0.3C/minlinear rate from 25 to 250C. It shall include a sensing systemcapable of detecting the softening point with an accuracy of0.1C.5.1.3 Sample Cup Assemb

    11、lyA chromium-plated brass cupconforming to the dimensions shown in Test Method D 566. Itshall be placed in an assembly so that the sample flows downa distance of 19 mm to interrupt a light beam to cause digitaldisplay of the softening point.6. Preparation of Sample6.1 For waxes heat the sample to 15

    12、 to 20C above itsmelting point to form a pourable liquid. Place the sample cupson glass slides and pour the melted sample into the cup to alevel even with the upper rim of the cup. Allow the sample tostand at room temperature for 2 h before running.7. Preparation of Apparatus7.1 Ensure that the furn

    13、ace unit and the sample cup assem-bly are clean and bright, since tarnished or dirty apparatus willchange the apparent dropping point. After each determination,check to see if the apparatus requires cleaning.NOTE 1It is advisable to keep the equipment covered when not in use.1This test method is und

    14、er the jurisdiction of ASTM Committee D21 on Polishesand is the direct responsibility of Subcommittee D21.02 on Raw Materials.Current edition approved Sept. 1, 2004. Published September 2004. Originallyapproved in 1980. Last previous edition approved in 1999 as D 3954 94 (1999).2For referenced ASTM

    15、standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Mettler FP5/53 model, FP80/83 model, and FP90/83 model are available fromthe Mett

    16、ler Instrument Corp., Princeton-Hightstown Road, Hightstown, NJ 08520.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.8. Procedure8.1 The procedure for measuring the dropping point ofwaxes with the Mettler instrument has been develop

    17、ed toduplicate the results obtained by Test Method D 566.8.2 Preheat or cool the furnace unit to a temperature of 20 to25C less than the expected dropping point (Note 2) of thesample and maintain at this temperature. Place the cartridgeassembly containing the sample in position in the furnace,taking

    18、 care that the slits for the light beam are properlypositioned. When the ready light becomes steady, indicatingthe sample and furnace have equilibrated at the presenttemperature, initiate the 2C/min heating rate by pressing theSTART LEVEL. Heating will then continue automatically untilthe drop point

    19、 occurs and the dropping point temperature isdisplayed on the digital readout.NOTE 2In the event of a dispute, the purchaser and the seller shouldagree on the exact starting temperature to be used.8.3 Immediately remove the cartridge assembly uponcompletion of the test. Check to determine if the sam

    20、ple haspassed the light beam slot and no pretrigger has occurred.Inspect the dropping point apparatus to be sure no dirt,particles, or residue remain.8.4 Clean the sample cups by placing them upside down ona hard surface and punching out the residue material. Use aspatula shaped to the contours of t

    21、he cup, to remove theremaining particles with a gentle twirling motion.9. Report9.1 Report the dropping point recorded on the digitalreadout to the nearest 0.1C. If converted to degrees Fahren-heit, report to the nearest 0.2F. Experience has indicated thatduplicate runs are not necessary. If a known

    22、 error in experi-mental procedure is made, the result should be discarded and asecond run should be made.10. Precision10.1 The following criteria shall be used for judging theacceptability of results (95 % probability) for the Mettlerdropping point:10.1.1 RepeatabilityDuplicate results by the same o

    23、pera-tor shall not be considered suspect unless they differ by morethan 0.5C.10.1.2 ReproducibilityThe results reported by each of twolaboratories shall not be considered suspect unless the reportedvalues differ by more than 1.5C.10.1.3 The procedure in this test method has no bias becausethe values

    24、 derived for the drop point of waxes are defined onlyin terms of this test method.11. Keywords11.1 drop point; waxesASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly a

    25、dvised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, eith

    26、er reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend.

    27、 If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).D 3954 94 (2004)2


    注意事项

    本文(ASTM D3954-1994(2004) Standard Test Method for Dropping Point of Waxes《石蜡滴点的标准试验方法》.pdf)为本站会员(lawfemale396)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开