欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    ASTM D3883-2004(2008) Standard Test Method for Yarn Crimp and Yarn Take-up in Woven Fabrics《机织织物中纱线卷曲性或卷绕性的标准试验方法》.pdf

    • 资源ID:515711       资源大小:73.92KB        全文页数:4页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    ASTM D3883-2004(2008) Standard Test Method for Yarn Crimp and Yarn Take-up in Woven Fabrics《机织织物中纱线卷曲性或卷绕性的标准试验方法》.pdf

    1、Designation: D 3883 04 (Reapproved 2008)Standard Test Method forYarn Crimp and Yarn Take-up in Woven Fabrics1This standard is issued under the fixed designation D 3883; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of la

    2、st revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the determination of the rela-tionship between the length of a piece of fabric and the lengthof

    3、the yarn in the fabric by measurement of the yarn crimp andyarn take-up.1.2 This test method applies to woven fabrics.1.3 The values stated in either SI or inch-pound units are tobe regarded separately as standard. Within the text, theinch-pound units are shown in parentheses. The values statedin ea

    4、ch system are not exact equivalents; therefore, eachsystem shall be used independently of the other. Combiningvalues from the two systems may result in nonconformancewith the specification.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is

    5、 theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D 123 Terminology Relating to TextilesD 1776 Practice for Conditioning and Testing

    6、TextilesD 2904 Practice for Interlaboratory Testing of a Textile TestMethod that Produces Normally Distributed DataD 2906 Practice for Statements on Precision and Bias forTextiles3D 4849 Terminology Related to Yarns and FibersD 4850 Terminology Relating to Fabrics and Fabric TestMethods3. Terminolog

    7、y3.1 For definition of textile terms used in this test method:bench marks, refer to Terminology D 4849.3.2 For definitions of textile terms used in this test method:yarn crimp and yarn take-up, refer to Terminology D 4850.3.3 For definitions of other textile terms used in this testmethod, refer to T

    8、erminology D 123.4. Summary of Test Method4.1 Bench marks are placed on a length of a yarn as it liesin a woven fabric. The distance between the bench marks ismeasured. The yarn is removed from the fabric, straightened byapplying suitable tension, and the distance between the benchmarks is remeasure

    9、d. Yarn crimp is the change in lengthexpressed as a percent and based on the in-fabric distance. Yarntake-up is the change in length expressed as a percent andbased on the out-of-fabric distance.5. Significance and Use5.1 The relationship of the length of a piece of fabric and thelength of yarn in t

    10、he fabric can be determined accurately onlybe measuring the length of yarn entering the loom and thelength of fabric made from that particular length of yarn. Inmost cases, however, the determination must of necessity bemade on a woven fabric by measuring the length of yarnremoved from a measured le

    11、ngth of fabric, thus introducingcertain variations that will influence the accuracy of the test.Yarn removed from the woven fabric contains undulations orwaves that have been introduced by the weaving process. Heat,moisture, and mechanical shrinkage on subsequent finishingoperations may accentuate t

    12、hese undulations, and in all prob-ability, increase the force to pull them out and straighten theyarn. In order to accurately measure the length of the yarn afterthe removal of the crimp, these undulations must be pulled outwithout elongating the yarn. In some cases, the minimum forcenecessary to st

    13、raighten the yarn will cause a certain amount ofthe elongation to take place, thus increasing the length of theyarn. Also, stresses imposed upon the yarn during the weavingprocess may have been sufficient to stretch the yarn beyond itselastic limit, again increasing its length. It is recognized that

    14、determination made by measuring length of yarn removed froma measured length of fabric may tend to give crimp values thatare somewhat higher than the crimp in the yarn as it lay in thefabric. In the case of fabrics made from yarns that exhibitdifferential shrinkage, or yarns of widely different coun

    15、t, oryarns woven at different tensions, the crimp of each type ofyarn in the fabric must be determined and reported separately.1This test method is under the jurisdiction of ASTM Committee D13 on Textilesand is the direct responsibility of Subcommittee D13.59 on Fabric Test Methods,General.Current e

    16、dition approved July 1, 2008. Published October 2008. Originallyapproved in 1980. Last previous edition approved in 2004 as D 3883 04.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume info

    17、rmation, refer to the standards Document Summary page onthe ASTM website.3Withdrawn. The last approved version of this historical standard is referencedon www.astm.org.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5.2 This test met

    18、hod can be used for acceptance testing ofcommercial shipments but comparisons should be made withcaution because information on estimates of between-laboratory precision is limited as noted in 13.1.5.2.1 If there are differences of practical significance be-tween reported test results for two labora

    19、tories (or more),comparative tests should be performed to determine if their isa statistical bias between them, using competent statisticalassistance. As a minimum, ensure the test samples to be usedare as homogeneous as possible, are drawn from the materialfrom which the disparate test results were

    20、 obtained, and arerandomly assigned in equal numbers to each laboratory fortesting. The test results from the two laboratories should becompared using a statistical test for unpaired data, at aprobability level chosen prior to the testing series. If a bias isfound, either its cause must be found and

    21、 corrected, or futuretest results for that material must be adjusted in considerationof the known bias.6. Apparatus6.1 Suitable Device4, for straightening the yarn throughapplication of horizontal or vertical tension, having two yarnsupport surfaces or two clamps, the distance between whichmay be al

    22、tered in order to apply the needed tension.6.2 Suitable Marking Device, for marking bench marks onthe yarn specimen.7. Sampling and Test Specimens7.1 Primary Sampling UnitConsider rolls of fabric orfabric components of fabricated systems to be the primarysampling unit, as applicable.7.2 Laboratory S

    23、ampling UnitAs a laboratory samplingunit take from rolls two pieces of fabric, full width, each 375mm (15 in.) in length along the selvage (machine direction)after removing a first 1-mm (1-yd) length. For fabric compo-nents of fabricated systems use the entire system.7.3 Test SpecimensFrom each labo

    24、ratory sampling unit,as required for each the warpwise and fillingwise directions,take ten test specimens, each 300 mm (14 in.) long as directionin Section 9. Consider the long direction as the direction of test.7.3.1 For fabric widths 125-mm (5-in.) or more, take nospecimen closer than 25-mm (1-in.

    25、) from the selvage edge.7.3.2 For fabric widths less than 125-mm (5-in.), use theentire width for specimens.7.3.3 Ensure specimens are free of folds, creases, orwrinkles. Avoid getting oil, water, grease, etc., on the speci-mens when handling.7.3.4 If the fabric has a pattern, ensure that the specim

    26、ensare a representative sampling of the pattern.8. Conditioning8.1 Condition the specimens by bringing them to approxi-mate moisture equilibrium in the standard atmosphere forconditioning textiles as directed in Practice D 1776.9. Preparation of Test Apparatus and Calibration9.1 Set-up procedures fo

    27、r machines from different manufac-turers may vary. Prepare and verify calibration of the testingdevice as directed in the manufacturers instructions.10. Procedure10.1 Test the specimens in the standard atmosphere fortesting textiles, as described in Practice D 1776.10.2 Handle the test specimens car

    28、efully to avoid alteringthe natural state of the material.10.3 Test ten specimens from the warpwise direction or tenspecimens from the fillingwise direction, or both, as required ina material specification or contact order.10.4 Using the marking device, make two lines (benchmarks) 250 mm (10 in.) ap

    29、art, perpendicular to the yarn beingtested and extending 25 mm (1 in.) into the fabric, and recordthe distance between bench marks as distance (F) (in-fabricdistance).10.4.1 If a direct reading device is used, follow the manu-facturers recommendations for establishing the specimenlength.10.5 Prepare

    30、 an edge by making a cut at least 350 mm (14in.) long, parallel, and in the direction of the yarn to bemeasured, and such that it crosses near the ends of both linesof the bench mark.10.6 Ravel several yarns from the cut edge, such that theycontain the bench marks.10.7 One at a time, when ready to u

    31、se, ravel ten yarnspecimens from the prepared edge of the fabric. Ensure that thebench marks appear on each yarn. Take care not to disturb thetwist or strain the yarn. Maintain identity of the fabric directionbeing evaluated, that is, warpwise or fillingwise.10.8 Fasten one of the yarn specimens in

    32、the clamps of atensioning device or, if applicable, in the proper position of theyarn supports of a direct reading crimp tester with the benchmarks coincident with the nips of the respective clamps that areset for the initial in-fabric length.10.8.1 Clamp type devices may consist of a twist counterf

    33、itted with graduated sliding clamp, or a tension testingmachine or which the movement or action can be stoppedinstantly at any point, such as the constant-rate-of-elongation(CRE-Type) or other similar instrument. For a direct readingcrimp tester, the yarn is placed under the hook of the movableshaft

    34、 with the bench marks on the yarn aligned with the upperfixed yarn supports.10.9 Apply a force to the yarn just sufficient to removeundulations due to weaving, without imparting stretch asdetermined by using one of the following three options.NOTE 1The three options can give different results. For m

    35、aximumprecision between laboratories, it is recommended that the laboratories usethe same equipment and the same option.10.9.1 Option A, By HandStraighten the yarn by handagainst a scale graduated in 1 mm (116 in.), observe and recordthe distance between bench marks to the nearest 1 mm (116 in.)as (

    36、Y) (straightened yarn distance).NOTE 2This is the least accurate option because the tension requiredto remove crimp is unknown.4Commercially available devices that have been found acceptable are a twisttester with tension device, a tensile testing machine, and a crimp tester of the directreading typ

    37、e.D 3883 04 (2008)210.9.2 Option B, by Tension Device or Crimp TesterUsingone of the tensioning devices or crimp tester, apply a tensionforce based upon the known yarn size. If the tension force isnot sufficient to remove all the crimp, gradually increase thetension force until the crimp just remove

    38、d. Use the determinedforce on all the yarns in the set and proportional force on anyother samples in the series or test.10.9.2.1 Estimate the required tension force using Eq 1:Tensile force, g 5 yarn number in tex 3 0.25 (1)10.9.3 Option C, Tensile Testing MachineUsing aconstant-rate-of-extension (C

    39、RE-type) of testing machine, de-termine the force to remove undulations by analysis of aforce-extension as described in 10.9.3.1.10.9.3.1 Establish Point A as the point where the force-extension curve begins, that is, zero force and zero extension.Extrapolate the straight-line portion of the force-e

    40、xtensioncurve through the extension axis, Line CE. The portion of thecurveAD represents the removal of the crimp and initial stretchof the yarn. Establish Point D where the force-extension curveseparates from the line CE. Establish Point B by constructinga line from Point C, parallel to the force ax

    41、is to curve AD.Establish Point L by constructing a line from Point B throughthe force axis, parallel to the extension axis. The forcecorresponding to Point L is the required tensile force to removethe crimp without stretching (see Fig. 1).10.10 Determine and record the length of the yarn to theneare

    42、st 2.5 mm (0.1 in.) after removal of the crimp as follows:10.10.1 For clamp-type devices, measure the distance be-tween the bench marks on the straightened yarn and record asdistance (Y) (straightened yarn distance).10.10.2 For constant-rate-of-extension machines, determineand record the straightene

    43、d distance (Y) between bench marksdirectly from the extension axis of the force-extension curveillustrated on Fig. 1 by line LB, projected to the extension axis,allowing for any chart magnification ratio.10.10.2.1 For some tensile testers, straightened yarn dis-tance (Y) and the percent yarn crimp o

    44、r yarn take-up can becomputer-processed automatically.10.10.3 For direct-reading crimp testers, read the yarn crimpor yarn take-up directly from the dial or scale.11. Calculation11.1 Calculate the average distance between the two benchmarks on the straightened yarn for all measured specimens tothe n

    45、earest 2.5 mm (0.1 in.), for each warpwise direction andfillingwise direction, as applicable.11.2 Calculate the average yarn crimp or average yarntake-up to the nearest 0.1 % using Eq 2 or Eq 3, for eachwarpwise direction and fillingwise direction, as applicable:C 5 100Y2F!/F (2)T 5 100Y2F!/Y (3)whe

    46、re:C = yarn crimp, %,T = yarn take-up, %,F = average of distances between bench marks on yarn infabric, mm (in.) (from 10.4), andY = average of distances between bench marks on yarnafter removal from fabric and straightened under ten-sion, mm (in.) (from 10.10).11.2.1 When data are computer-processe

    47、d automatically,calculations generally are contained in the associated software.It is recommended that computer processed data be verifiedagainst known property values and its software described in thereport.11.2.2 For direct-reading crimp testers, the yarn crimp oryarn take-up is read directly from

    48、 the dial or scale.12. Report12.1 The report shall contain the following information:12.1.1 Report that the yarn crimp and yarn take-up wasdetermined as directed in Test Method D 3883. Describe thematerial or product sampled and the method of sampling used.12.1.2 Report the following information for

    49、 the warpwiseand fillingwise directions for the laboratory sampling unit andfor the lot as applicable to a material specification or contractorder.12.1.2.1 Average yarn crimp and average yarn take-up;12.1.2.2 Test option, manufacturer, and model of test instru-ment;12.1.2.3 Force used to remove crimp;12.1.2.4 When calculated, the standard deviation or thecoefficient of variation.12.1.2.5 For computer-processed data, identify the program(software) used.FIG. 1 Example Chart For Determining of Tensile Force UsingOption CD 3883 04 (2008)313. Precision and Bias13.1 Interl


    注意事项

    本文(ASTM D3883-2004(2008) Standard Test Method for Yarn Crimp and Yarn Take-up in Woven Fabrics《机织织物中纱线卷曲性或卷绕性的标准试验方法》.pdf)为本站会员(roleaisle130)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开